Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 45, Problem 5RQ
Describe the proper procedure to seal a puncture in a tire.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Which of the following would NOT be cause for rejection when checking the tire condition?
Any tire has a fabric break or cut exposing ply or cord or any tire is in contact with the body or frame.
Any tire tread or recap is separated or any tire is flat.
All of the statements shown are cause for rejection.
Any tire has any bumps, bulges, or knots or is repaired with a boot or blowout patch.
Which of the following statement is correct
Select one:
Friction causes objects to slip down
Friction causes objects to slow down
Friction causes objects to break down
Friction causes objects to move at small force
1.Name type of failures in engine blocks
Chapter 45 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 45 - List five things that could cause premature...Ch. 45 - Define lateral and radial runout.Ch. 45 - Prob. 3RQCh. 45 - Define dynamic and static wheel balance.Ch. 45 - Describe the proper procedure to seal a puncture...Ch. 45 - The rim offset is the vertical distance between...Ch. 45 - Prob. 7RQCh. 45 - True or False? All TPMS have a pressure sensor...Ch. 45 - A tire that wobbles from side-to-side is said to...Ch. 45 - A front tire has excessive wear on both edges of...
Ch. 45 - All of the following statements are correct...Ch. 45 - All of the following statements are correct...Ch. 45 - Which of the following statements about sidewall...Ch. 45 - All of these statements about improper wheel...Ch. 45 - Prob. 15RQCh. 45 - Technician A says that the front wheel bearings on...Ch. 45 - Technician A says that dynamic wheel imbalance...Ch. 45 - Technician A says that front bearing assembly...Ch. 45 - Technician A says that replacement wheel rims...Ch. 45 - Prob. 5ASRQCh. 45 - While choosing the correct tire for a vehicle:...Ch. 45 - Technician A says that on most vehicles, the...Ch. 45 - Prob. 8ASRQCh. 45 - Prob. 9ASRQCh. 45 - Prob. 10ASRQ
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- How does a technician determine the proper inflation for a vehicle's tires?arrow_forwardwhat is the formula to measure gas from tire interior?arrow_forwardA tire that wobbles from side-to-side is said to have -----· a.radial runout b.lateral runout c.static imbalance d.none of the abovearrow_forward
- While diagnosing the problems that can be caused by worn tie-rod ends: Technician A says that they can cause scalloped and scuffed tires. Technician B says that they can cause the vehicle to pull to one side. Who is correct?arrow_forwardDescribe an application that can pass vehicle safety assessments.arrow_forwardExplain why a TPMS relearn should be performed even after a basic tire service.arrow_forward
- Repair work performed on vehicles still under tire manufacturers warranty is usually performed by independent service shops dealerships specialty shops either a or barrow_forwardAll of the following statements are correct except? a. Belts are reinforcing materials that encircle the tire under the tread. b. The carcass of a tire is made up of plies, layers of cloth, and rubber. c. Most tread patterns are designed to work well on both wet and dry roads. d. The bead is the decorative pattern at the outer edge of the tread.arrow_forwardAn indirect TPMS is being discussed. Technician A says that if a specific tire is low, the system will typically alert the driver which tire is low. Technician B says that after serving the indirect TPMS, you need to perform a re-learn procedure. Who is correct? Technician A Technician B Both Technician A and B Neither Technician A or Barrow_forward
- Which of the following statement is correct Select one: Friction is good at smooth surfaces Friction is high for rough surfaces Friction is zero for smooth surfaces Fiction is very bad at rough surfacesarrow_forwardAll of the following statements are correct except?a. Tire inflation pressure directly affects traction.b. The recommended tire pressure for front andrear tires may be different.c. The recommended tire pressures are oftenlower than maximum pressures.d. The recommended tire pressure is moldedinto the sidewall of the tirearrow_forwardWhich of the following is true about a brake service? A. It should always include a comprehensive brake inspection B. It requires specialized tools. C. It may lead to additional work if performed properly. C. All of the abovearrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Principles of Lubrication | Automobile Engineering; Author: Magic Marks;https://www.youtube.com/watch?v=MGbbSxZTdCQ;License: Standard Youtube License