Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 49, Problem 10ASRQ
While performing a prealignment inspection: Technician A says that a prealignment inspection should include checking the vehicle interior for heavy items. Technician B says that tools and other items normally carried in the vehicle should be included during an alignment. Who is correct?
- Technician A only
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
An indirect TPMS is being discussed. Technician A says that if a specific tire is low, the system will typically alert the driver which tire is low. Technician B says that after serving the indirect TPMS, you need to perform a re-learn procedure. Who is correct?
Technician A
Technician B
Both Technician A and B
Neither Technician A or B
A vehicle with a direct TPMS system keeps showing “Low-Left Front Tire,” but when checked, the tire is within specification. Which of the following would be the most likely cause?
A broken reluctor wheel
Multiple TPMS sensors have failed
The tires were rotated without doing a re-learn procedure
A faulty wheel speed sensor
Which of the following would NOT be cause for rejection when checking the windshield and other glass?
Any window is broken or has sharp or jagged edges.
Any window other than the windshield is cracked, starred, scratched, or discolored so as to obstruct the driver’s view.
The vehicle is not equipped with approved safety glass or is not equipped with a windshield.
The windshield has a 2 inch diameter“star”.
Chapter 49 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 49 - Define camber.Ch. 49 - What tire wear pattern will result from excessive...Ch. 49 - What can be caused by excessive negative caster?Ch. 49 - Describe the difference between toe-in and...Ch. 49 - Describe thrust angle and why it is important foi...Ch. 49 - What can cause incorrect toe-out-on-turns?Ch. 49 - In what direction must the bottom of a tire and...Ch. 49 - What is scrub radius and why is it important?Ch. 49 - Prob. 9RQCh. 49 - Describe how caster adjustment may be used to com...
Ch. 49 - Which of the following is a good definition of...Ch. 49 - Prob. 12RQCh. 49 - A 3-degree difference in the SAI angle on each...Ch. 49 - Unequal SAI angles on the left and right sides of...Ch. 49 - While driving straight, a FWD car pulls to the...Ch. 49 - Technician A says that negative caster provides...Ch. 49 - Technician A says that the purpose of the steering...Ch. 49 - Technician A says that the presence of a thrust...Ch. 49 - Technician A says that camber changes as the...Ch. 49 - Technician A says that caster can be adjusted on...Ch. 49 - Technician A says that on FWD vehicles, the front...Ch. 49 - Technician A says that if caster at both wheels is...Ch. 49 - While discussing front-wheel caster: Technician A...Ch. 49 - While performing a prealignment inspection:...Ch. 49 - While performing a prealignment inspection:...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- All of the following statements are correct except? a. Belts are reinforcing materials that encircle the tire under the tread. b. The carcass of a tire is made up of plies, layers of cloth, and rubber. c. Most tread patterns are designed to work well on both wet and dry roads. d. The bead is the decorative pattern at the outer edge of the tread.arrow_forwardWhile discussing what the maintenance reminders base die time for the next service on: Technician A says that future service is based on the type of driving the vehicle has seen since the last service. Technician B says that the next interval is based only on the number of miles or kilometers since the last service. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardTechnician A uses a crane to remove an engine from its compartment- Technician B uses an engine cradle to remove an engine from its compartment Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- Which of the following statements about unibody construction is not true? A unibody is a stressed hull structure in which each of the body parts supplies structural support and strength to the entire vehicle. Unibody vehicles tend to be tightly constructed because the major parts are all welded together. All unibodies are constructed from steel. Most front-wheel-drive unibody vehicles have a cradle or partial frame.arrow_forwardTechnician A says that seat belt webbing should be replaced if it is bowed. Technician B says that webbing does not need to be replaced if the color has merely faded due to exposure to the sun. Who is correct? Technician A only Technician B only Both A and B Neither A nor Barrow_forwardWhile diagnosing the cause of a clicking noise that is heard only when the car is turning: Technician A says that the most probable cause is a worn wheel bearing. Technician B says that the most probable cause is a worn outboard CV joint. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
- FGI and FKJ correct but incorrect afterwards.arrow_forwardTechnician A says the front wheel bearings on a typical FWD car are sealed and non-adjustable. Technician B says the front wheel bearings on a typical FWD car are greaseable and adjustable. Who is correct?arrow_forwardList at least five separate checks that should be made during the visual inspection of tje transmission/transaxlearrow_forward
- Discuss the different things/parts to be done/inspected before operating a farm tractor.arrow_forwardAfter removing the vehicles hood in preparation for removing the engine: Technician A places the hood on the roof of the vehicle. Technician B sets the hood aside in a safe place on fender covers or cardboard. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardTechnician A says that the transmission rear seal at the driveline is particularly prone to leakage. When Technician B pushes up and down on the transmission, he says that the mounts require replacement because the case moves up and down. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
General Industrial Safety; Author: Jim Pytel;https://www.youtube.com/watch?v=RXtF_vQRebM;License: Standard youtube license