Describe how caster adjustment may be used to compensate for road crown.

Q: anism?

A: Inversions of mechanism: A mechanism is one wherein one of the hyperlinks of a kinematic chain is…

Q: Which of the following is not a type of adjustment to a dozer blade? Camber Pitch Tilt Angle

A: Option (a)  camber

Q: List five things that could cause premature bearing failure

A: No matter what, things are bound to break. The same holds for bearing. But it can be prevented by…

Q: List the missing parts Reciprocating motion Crank mechanism

A: A connecting rod in the engine is used to connect the piston with the crank rod. one end is attached…

Q: Explain the job of Rudder

A: The rudder is a primary flight control surface that controls rotation about the vertical axis of an…

Q: An instrument often used to check the alignment of twoshafts is theA. micrometer.B. dial…

A: different types of instruments have used the measurement of the different dimensions of the…

Q: Write about characteristics of gyroscope with a neat sketch.

A: The answer is in next steps

Q: g two (2) cylincer types:

A: 1. SINGLE ACTING CYLINDER 2.DOUBLE ACTING CYLINDER

Q: an be manufactured by cast aluminum alloy only.  a. Nose Section b. Power Section c. Supercharger…

A: we have to determine which of the sections of radial engine can be manufactured by aluminum casting

Q: how to design shaft based on critical speed for agitator?

A: Design of shaft for agitator:- .Tip speed- it is defined by speed of the agitator's blade tip or…

Q: at direction should you paddle te

A: 21.80 Degree ( from downstream)

Q: triple beam balance?

A: Explanation given below.

Q: Explain the Jog/shuttle mechanism.

A: The explanation about the Jog/shuttle is given as under.

Q: Explain the purpose of the wheel rim drop center and safety ridges.

A: The purpose of the wheel rim drop center is to allow mounting of the tires, we can easily install…

Q: Draw a detailed with explanation Free Body Diagram of a Tripod

A:

Q: onsidered as d

A: given: Describe the nature of force vibrations why their considered as destructive.

Q: What occurs when a wheel hits a dip or hole and moves downward? a. Jounce b. Free length c.…

A: Given Data : Wheel

Q: Explain in detail about the two types of shaft alignment, soft foot, and indicator sag.

A:

Q: Multiple choice Which wheelbarrow shown is well designed

A: Given:

Q: what parts provide for toe-out on turns

A: Toe-out on turns is a toe setting for the front wheels so that it can make turns. While making a…

Q: g. Predict the skid distance it

A: 192m detailed Explanation given in attachment.

Q: Write short notes on points to be considered during maintenance of wiper pad on the lathe machine.

A: points to be considered during maintenance of wiper pad on the lathe machine.

Q: the speed can be positive or negative false true

A: Speed is a scalar quantity. it has no direction so, speed can be positive or zero. it cannot be…

Q: Explain by drawing a figure the recovery or capsizing (overturning) situation of a boat in the water…

A: Capsizing when a boat or ship is turned on its side or it is upside down in the water then…

Q: Describe how to measure main bearing oil clearance

A: Estimating principle oil bearing freedom is one of those means that all great motor developers…

Q: Worn teeth on a speed gear can cause?

A: worn teeth creates a big problem in gear drive.

Q: If the shaft is always smaller than the hole, general fit name is Fill in the blank with correct…

A: If the shaft is always smaller than the hole, general fit name is_______________. Answer: D)…

Q: ion 3 plain the importance of: rake angle relief angle nose radius

A:

Q: List four possible causes of cluth slippage

A: A Clutch is a mechanical device used in vehicles that transmits power from the motor to the…

Q: rotates clockwise at 1150 rpm

A:

Q: By using AutoCAD command draw the following samples with possible fitting. 1- Main door 2- Boiler 3-…

A: Given question: By using AutoCAD commands draw the following : 1. Main Door 2. Boiler 3.…

Q: What is the job of wheel cylinder stops?

A: Wheel cylinder is a component of a hydraulic drum brake system.it locates in each wheel and…

Q: А В C

A:

Q: The amount of force generated by an air bearing decreases when?

A: The amount of force generated by an air bearing decrease when

Q: Tech A states to check the camshaft for lift, the cam must be removed from the engine.  Tech B says…

A: The cam is a major component of a four stroke engine which is responsible for the proper operation…

Q: SLPM stands for _______ liters per minute a. speed b. standard c. static d. specific

A: SLPM is a unit of measuring volumetric flow rate of a gas.

Q: Different types of altimeters

A: TO BE EXPLAIN- Different types of altimeter. Altimeter is a device which measures the altitude of…

Q: B _7m Gm Tom

A:

Q: sing) slope with a c

A:

Q: A chain saw will run in many positions. Tech a says that this is because of its float type…

A: A chain saw will run in many positions because of its diaphragm type carburetor. Diaphragm allows…

Q: Derive an expression for the height of propell governor

A: Governors are the most effective way to manage or regulate an engine's speed based on variable…

Q: flyw

A: compare governor and flywheel

Q: When removing or installing bearing, where should force be applied

A: The application of force during installation or removal of bearing is one of the critical factors,…

Q: 3. What is the difference between Turn Coordinator and Turn and Slip Indicator?

A: the turn and slip indicator and turn coordInator are very similar.in fact , the turn and slip…

Q: 8.Which of the following pairs is high pair? A sliding pair В cam pair C screw pair

A: Higher pair: When the two elements have point or line contact while in motion then the pair is known…

Q: mm - The mating shaft has a clearanc

A:

Q: Identify a true statement while maintaining wiper pads used on lathe machine

A: The Wiper pads are used for cleaning the small piece of the chips which can not be cleaned by the…

Q: Question 5 Anti-friction bearings require more space than plain bearings. O True False

A: Bearing:A friction bearing consists of a fixed, non-moving bearing surface, such as machined metal…

Q: ladde

A: ax=14.01m/s^2

Metal Casting

Metal casting is described as a manufacturing process in which a mold cavity is produced by sand, and molten metal is filled inside a mold cavity. The desirable shaped object is achieved after the solidification of molten metal. Large metal objects like machine beds, motor bodies, and others can easily be manufactured using metal casting. The place or shop where metal casting is performed is called foundry.