Technician A says that flare nut or line wrenches should be sued to loosen or tighten brake line or tubing fittings Technician B says that open-end wrenches will surround the fitting's nut and provide a positive grip on the fitting. Who is correct? Group of answer choices Technician A only Technician B only Both Technicians A and B Neither A nor B

Technician A says that flare nut or line wrenches should be sued to loosen or tighten brake line or tubing fittings Technician B says that open-end wrenches will surround the fitting's nut and provide a positive grip on the fitting. Who is correct? Group of answer choices Technician A only Technician B only Both Technicians A and B Neither A nor B

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter52: Disc Brakes

Section: Chapter Questions

Problem 8ASRQ: Technician A says that fixed calipers use a piston on each side of the rotor to apply the brakes....

See similar textbooks

Similar questions

When replacing brake pads on a vehicle: Technician A works on one wheel before beginning work on an-other. Technician B uses a minimum of 52 psi of air pressure to force the piston from the caliper housing. Who is correct?
During a brake inspection, the inner brake pad is found to be 3mm thick, while the outside pad is 8mm. Techinician A says this is a sign of a poorly lubricated hardware. Technician B says this is normal wear for brake pads. Who is correct? A. Technician A B. Technician B C. Both Technician A and B D. Neither Technician A or B
Which of the following statements about drum brakeshoes is not true?a. Web thickness varies only with changes in shoesize.b. Many shoes have indented places along the edgeof the rim.c. The shoe rim is welded to the web.d. The primary/leading shoe is typically the one thatis positioned toward the front of the vehicle
Which of the following statements about drum brake shoes is not true? a. Linings may be riveted or bonded to the shoes. b. Shoe indentions hold the shoe in place against the backing plate. c. The shoe rim supports the shoe lining. d. The primary/leading shoe is typically the one that is positioned toward the front of the vehicle.
Asbestos has not been used in brake linings or pads since 2003. a. True b. False Technician A says low-drag calipers retract the pistons and pads farther from the rotor than traditional calipers. Technician B says systems that use low-drag calipers cannot use quick take-up master cylinders. Who is correct? a. A only b. B only c. both A and B d. neither A nor B A brake line must be single-flared to provide a good seal at a joint or junction block. a. True b. False Vehicles use brake pedal position sensors. a. True b. False
True or False? Backing plates, struts, levers, and other metal brake parts should be cleaned with a wet-cleaned using water or a water-based solution.
The basic frictional parts of a brake system are being discussed: Technician A says that the harder the frictional parts are pushed together, the higher the friction. Technician B says that the harder the frictional parts are pushed together, the more heat is developed. Who is correct? Technician A only Technician B only Both A and B Neither A nor B
When reassembling an overhauled brake caliper: Technician A cleans brake components in denatured alcohol. Technician B cleans brake components in clean brake fluid. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor B
While diagnosing the cause of noise from a transfer case: Technician A says that a probable cause is incorrect tire size. Technician B says that the most probable cause is a faulty bearing or gear. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor B
Backing plates, struts, levers, and other metal brake parts should be. wet-cleaned using water or a water-based solution wet-cleaned using an alcohol-based solvent wet-cleaned using gasoline dry-cleaned only
Technician A says that the discard dimension of a brake drum is the drums allowable machining dimension. Technician B says that the discard dimension is the allowable wear dimension. There must be 0.030 inch left for wear after machining. Who is correct? Technician A only Technician B only Both A and B Neither A nor B
True or False? Disc brakes are not as likely to fade during heavy braking as are drum brakes.