BuyFind*arrow_forward*

6th Edition

KASSIMALI + 1 other

Publisher: Cengage,

ISBN: 9781337630931

Chapter 5, Problem 58P

Textbook Problem

146 views

Draw the shear, bending moment, and axial force diagrams and the qualitative deflected shape for the frame shown.

To determine

Plot the shear diagram, bending moment diagram, axial force diagram, and the qualitative deflected shape of the frame.

Write the condition for static instability, determinacy and indeterminacy of plane frames as follows:

Here, number of members is *m*, number of external reactions is *r*, the number of joints is *j*, and the number of elastic hinges is

Find the degree of static indeterminacy (*i*) using the equation;

Refer to the Figure in the question;

The number of members (*m*) is 2.

The number of external reactions (*r*) is 3.

The number of joints (*j*) is 3.

The number of elastic hinges

Substitute the values in Equation (2);

Show the free-body diagram of the entire frame as in Figure 1.

Find the vertical reaction at point *C* by taking moment about point *A*.

Find the vertical reaction at point *A* by resolving the vertical component of forces.

Find the horizontal reaction at point *A* by resolving the horizontal component of forces.

Show the free-body diagram of the members and joints of the entire frame as in Figure 2.

Consider point *A*:

Resolve the vertical component of forces.

Resolve the horizontal component of forces.

Consider the member *AB*:

Resolve the vertical component of forces.

Resolve the horizontal component of forces.

Take moment about the point *B*

Structural Analysis

Show all chapter solutions

Ch. 5 - Determine the axial forces, shears, and bending...Ch. 5 - Determine the axial forces, shears, and bending...Ch. 5 - Determine the axial forces, shears, and bending...Ch. 5 - Determine the axial forces, shears, and bending...Ch. 5 - Determine the axial forces, shears, and bending...Ch. 5 - Determine the axial forces, shears, and bending...Ch. 5 - Determine the axial forces, shears, and bending...Ch. 5 - Determine the axial forces, shears, and bending...Ch. 5 - Determine the axial forces, shears, and bending...Ch. 5 - Determine the axial forces, shears, and bending...

Ch. 5 - 5.1 through 5.11 Determine the axial forces,...Ch. 5 - Determine the equations for shear and bending...Ch. 5 - Determine the equations for shear and bending...Ch. 5 - Determine the equations for shear and bending...Ch. 5 - Determine the equations for shear and bending...Ch. 5 - Determine the equations for shear and bending...Ch. 5 - Determine the equations for shear and bending...Ch. 5 - Determine the equations for shear and bending...Ch. 5 - 5.12 through 5.28 Determine the equations for...Ch. 5 - 5.12 through 5.28 Determine the equations for...Ch. 5 - 5.12 through 5.28 Determine the equations for...Ch. 5 - 5.12 through 5.28 Determine the equations for...Ch. 5 - 5.12 through 5.28 Determine the equations for...Ch. 5 - 5.12 through 5.28 Determine the equations for...Ch. 5 - 5.12 through 5.28 Determine the equations for...Ch. 5 - 5.12 through 5.28 Determine the equations for...Ch. 5 - 5.12 through 5.28 Determine the equations for...Ch. 5 - 5.12 through 5.28 Determine the equations for...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - Draw the shear and bending moment diagrams for the...Ch. 5 - For the beam shown: (a) determine the distance a...Ch. 5 - For the beam shown: (a) determine the distance a...Ch. 5 - 5.55 and 5.56 Classify each of the plane frames...Ch. 5 - 5.55 and 5.56 Classify each of the plane frames...Ch. 5 - Draw the shear, bending moment, and axial force...Ch. 5 - Draw the shear, bending moment, and axial force...Ch. 5 - Draw the shear, bending moment, and axial force...Ch. 5 - Draw the shear, bending moment, and axial force...Ch. 5 - Draw the shear, bending moment, and axial force...Ch. 5 - Draw the shear, bending moment, and axial force...Ch. 5 - 5.57 through 5.71 Draw the shear, bending moment,...Ch. 5 - 5.57 through 5.71 Draw the shear, bending moment,...Ch. 5 - 5.57 through 5.71 Draw the shear, bending moment,...Ch. 5 - 5.57 through 5.71 Draw the shear, bending moment,...Ch. 5 - 5.57 through 5.71 Draw the shear, bending moment,...Ch. 5 - 5.57 through 5.71 Draw the shear, bending moment,...Ch. 5 - 5.57 through 5.71 Draw the shear, bending moment,...Ch. 5 - 5.57 through 5.71 Draw the shear, bending moment,...Ch. 5 - 5.57 through 5.71 Draw the shear, bending moment,...

Find more solutions based on key concepts

Show solutions Design an innovative system for transporting refuse from the kitchen to the curb. Cost should not be a major co...

Solid Waste Engineering

A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. F...

Steel Design (Activate Learning with these NEW titles from Engineering!)

The following are the results of a sieve analysis. a. Determine the percent finer than each sieve and plot a gr...

Principles of Geotechnical Engineering (MindTap Course List)

For a soil, given: D10 = 0.08 mm D30 = 0.22 mm D60 = 0.41 mm Calculate the uniformity coefficient and the coeff...

Fundamentals of Geotechnical Engineering (MindTap Course List)

What is the difference between steel and iron?

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

How do you test the efficiency of a secondary AIR system?

Automotive Technology

Rewrite the following WHERE clause without the use of the IN special operator: WHERE V_STATE IN (TN, FL, GA)

Database Systems: Design, Implementation, & Management

What would Iris have done differently if this adverse event had been much worse and had been declared a disaste...

Management Of Information Security

What actions would you recommend to minimize potential start-up issues for this virtual team?

Principles of Information Systems (MindTap Course List)

Write a query to display the current salary for each employee in department 300. Assume that only current emplo...

Database Systems: Design, Implementation, & Management

Do research to capture data on the growth of B2C c-commerce and retail sales over the past 10 years. Use the ch...

Fundamentals of Information Systems

Why would a manager prefer a decision tree instead of a decision table?

Systems Analysis and Design (Shelly Cashman Series) (MindTap Course List)

List the trip name of each trip that has the type Biking and that has Rita Boyers as a guide.

A Guide to SQL

Determine the resultant of the two forces and the couple.

International Edition---engineering Mechanics: Statics, 4th Edition

Which NGFW feature allows a network admin to restrict traffic generated by a specific game? a. Content filter b...

Network+ Guide to Networks (MindTap Course List)

What is the most common form of alarm? What does it detect? What types of sensors are commonly used in this typ...

Principles of Information Security (MindTap Course List)

What determines whether a conventional transmission or a transaxle is used?

Automotive Technology: A Systems Approach (MindTap Course List)

The system is a large ship and its contents. The inside of the ship and the air outside the ship are at the sam...

Fundamentals of Chemical Engineering Thermodynamics (MindTap Course List)

What is metrology?

Precision Machining Technology (MindTap Course List)

Would you classify the QueVision system as personal, group, or enterprise information system?

Fundamentals of Information Systems

List the methods by which an equipment grounding conductor is connected to a device box.

EBK ELECTRICAL WIRING RESIDENTIAL

Select the best answer for each of the following. A motor may be controlled remotely or automatically by using ...

Electric Motor Control

Accrued Wages Skiles Companys weekly payroll amounts to $15,000, and payday is every Friday. Employees work 5 d...

Cornerstones of Financial Accounting

In Windows, a _____ is a shortcut to apps or other content. (426) a. tile b. Launchpad c. ribbon d. Recycle Bin

Enhanced Discovering Computers 2017 (Shelly Cashman Series) (MindTap Course List)

A circular aluminum tube subjected to pure torsion by torques T(sec figure) has an outer radius r2equal to 1.5 ...

Mechanics of Materials (MindTap Course List)

If your motherboard supports ECC DDR3 memory, can you substitute non-ECC DDR3 memory?

A+ Guide to Hardware (Standalone Book) (MindTap Course List)

Referring to the graph in Figure 3-9, what would the voltage be for the CC power supply at 110 amps? What would...

Welding: Principles and Applications (MindTap Course List)