BuyFind*arrow_forward*

6th Edition

KASSIMALI + 1 other

Publisher: Cengage,

ISBN: 9781337630931

Chapter 5, Problem 62P

Textbook Problem

299 views

Draw the shear, bending moment, and axial force diagrams and the qualitative deflected shape for the frame shown.

To determine

Plot the shear diagram, bending moment diagram, axial force diagram, and the qualitative deflected shape of the frame.

Write the condition for static instability, determinacy and indeterminacy of plane frames as follows:

Here, number of members is *m*, number of external reactions is *r*, the number of joints is *j*, and the number of elastic hinges is

Find the degree of static indeterminacy (*i*) using the equation;

Refer to the Figure in the question;

The number of members (*m*) is 2.

The number of external reactions (*r*) is 3.

The number of joints (*j*) is 3.

The number of elastic hinges

Substitute the values in Equation (2);

Show the free-body diagram of the entire frame as in Figure 1.

Find the vertical reaction at point *A* by resolving the vertical component of forces.

Find the horizontal reaction at point *A* by resolving the horizontal component of forces.

Find the moment at point *A* by taking moment about point *A*.

Show the free-body diagram of the members and joints of the entire frame as in Figure 2.

Consider point *A*:

Resolve the vertical component of forces.

Resolve the horizontal component of forces.

Take the moment about point *A*

Structural Analysis

Show all chapter solutions

Ch. 5 - Determine the axial forces, shears, and bending...Ch. 5 - Determine the axial forces, shears, and bending...Ch. 5 - Determine the axial forces, shears, and bending...Ch. 5 - Determine the axial forces, shears, and bending...Ch. 5 - Determine the axial forces, shears, and bending...Ch. 5 - Determine the axial forces, shears, and bending...Ch. 5 - Determine the axial forces, shears, and bending...Ch. 5 - Determine the axial forces, shears, and bending...Ch. 5 - Determine the axial forces, shears, and bending...Ch. 5 - Determine the axial forces, shears, and bending...

Ch. 5 - 5.1 through 5.11 Determine the axial forces,...Ch. 5 - Determine the equations for shear and bending...Ch. 5 - Determine the equations for shear and bending...Ch. 5 - Determine the equations for shear and bending...Ch. 5 - Determine the equations for shear and bending...Ch. 5 - Determine the equations for shear and bending...Ch. 5 - Determine the equations for shear and bending...Ch. 5 - Determine the equations for shear and bending...Ch. 5 - 5.12 through 5.28 Determine the equations for...Ch. 5 - 5.12 through 5.28 Determine the equations for...Ch. 5 - 5.12 through 5.28 Determine the equations for...Ch. 5 - 5.12 through 5.28 Determine the equations for...Ch. 5 - 5.12 through 5.28 Determine the equations for...Ch. 5 - 5.12 through 5.28 Determine the equations for...Ch. 5 - 5.12 through 5.28 Determine the equations for...Ch. 5 - 5.12 through 5.28 Determine the equations for...Ch. 5 - 5.12 through 5.28 Determine the equations for...Ch. 5 - 5.12 through 5.28 Determine the equations for...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - 5.29 through 5.51 Draw the shear and bending...Ch. 5 - Draw the shear and bending moment diagrams for the...Ch. 5 - For the beam shown: (a) determine the distance a...Ch. 5 - For the beam shown: (a) determine the distance a...Ch. 5 - 5.55 and 5.56 Classify each of the plane frames...Ch. 5 - 5.55 and 5.56 Classify each of the plane frames...Ch. 5 - Draw the shear, bending moment, and axial force...Ch. 5 - Draw the shear, bending moment, and axial force...Ch. 5 - Draw the shear, bending moment, and axial force...Ch. 5 - Draw the shear, bending moment, and axial force...Ch. 5 - Draw the shear, bending moment, and axial force...Ch. 5 - Draw the shear, bending moment, and axial force...Ch. 5 - 5.57 through 5.71 Draw the shear, bending moment,...Ch. 5 - 5.57 through 5.71 Draw the shear, bending moment,...Ch. 5 - 5.57 through 5.71 Draw the shear, bending moment,...Ch. 5 - 5.57 through 5.71 Draw the shear, bending moment,...Ch. 5 - 5.57 through 5.71 Draw the shear, bending moment,...Ch. 5 - 5.57 through 5.71 Draw the shear, bending moment,...Ch. 5 - 5.57 through 5.71 Draw the shear, bending moment,...Ch. 5 - 5.57 through 5.71 Draw the shear, bending moment,...Ch. 5 - 5.57 through 5.71 Draw the shear, bending moment,...

Find more solutions based on key concepts

Show solutions For a soil, given: D10 = 0.08 mm D30 = 0.22 mm D60 = 0.41 mm Calculate the uniformity coefficient and the coeff...

Fundamentals of Geotechnical Engineering (MindTap Course List)

Draw the organic chemical formula for a polychlorinated dibenzodioxin, and describe how dioxins are controlled ...

Solid Waste Engineering

A column cross section is built up from fourL553 4 , as shown in Figure P4.9-9. The angles are held in position...

Steel Design (Activate Learning with these NEW titles from Engineering!)

As we explained in Chapter 10, viscosity is a measure of how easily a fluid flows. For example, honey has a hig...

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

The following values for a sand are given: D10 = 0.3 mm, D30 = 0.41 mm, and D60 = 0.77 mm. Determine Cu and Cc,...

Principles of Geotechnical Engineering (MindTap Course List)

Technician A says that some axle shafts are retained in the housing by a plate and bolts. Technician B says tha...

Automotive Technology

While discussing how to remove the piston from a brake caliper: Technician A says that the dust boot should be ...

Automotive Technology: A Systems Approach (MindTap Course List)

The dependency diagram in Figure Q6.8 indicates that a patient can receive many prescriptions for one or more m...

Database Systems: Design, Implementation, & Management

What is the sequence of the operations if the limit switches, shown in Figure 216, are used. (Limit switches we...

Electric Motor Control

Refer to the information for Morgan Inc. above. If Morgan uses a perpetual inventory system, what is the cost o...

Cornerstones of Financial Accounting

What is information technology and why is it important? Suggest three fictitious headlines that might be added ...

Systems Analysis and Design (Shelly Cashman Series) (MindTap Course List)

The force system acting on the machine part is equivalent to the single force R=80i+20jlb acting at O. Determin...

International Edition---engineering Mechanics: Statics, 4th Edition

What two codes are used to activate automatic cutter radius compensation? 15. What is the difference between th...

Precision Machining Technology (MindTap Course List)

In Question 8, suppose a new switch is connected to the first switch by way of a network cable, and three compu...

Network+ Guide to Networks (MindTap Course List)

Assume a smaller organization has a plan to implement a security program with three full-time staff and two or ...

Management Of Information Security

Which command terminates previously granted privileges?

A Guide to SQL

The _____ is the main circuit board of the computer. (278) a. ALU b. CPU c. motherboard d. system chassis

Enhanced Discovering Computers 2017 (Shelly Cashman Series) (MindTap Course List)

A split-level home has one stairway that has six risers between two levels of the home. Which of the following ...

EBK ELECTRICAL WIRING RESIDENTIAL

Assuming that pessimistic locking is being used but the two-phase locking protocol is not, create a chronologic...

Database Systems: Design, Implementation, & Management

What error did the Missile defense Agency make in the development of the GMD system?

Fundamentals of Information Systems

What kind of transaction processing systems does Cal need to manage and support the basic functions of his busi...

Fundamentals of Information Systems

A filtration system continuously removes water from a swimming pool, passes the water through filters, and then...

Fundamentals of Chemical Engineering Thermodynamics (MindTap Course List)

Would you expect to see more funds allocated to system development or to buying existing software and using sof...

Principles of Information Systems (MindTap Course List)

Using the categories of threats mentioned in this chapter and the various attacks described, review several cur...

Principles of Information Security (MindTap Course List)

An angle bracket having a thickness t = 0.75 in. is attached to the flange of a column by two 5/8-inch diameter...

Mechanics of Materials (MindTap Course List)

What must be checked before using the 110-volt power plug on a portable welder?

Welding: Principles and Applications (MindTap Course List)

If your motherboard supports ECC DDR3 memory, can you substitute non-ECC DDR3 memory?

A+ Guide to Hardware (Standalone Book) (MindTap Course List)