Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 50, Problem 2MC
Which of the following can lead to brake hose failure?
- Improperly matched fittings
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Which of the following is not a factor in determiningthe effectiveness of a brake system?a. Heat dissipationb. Lubricantc. Pressured. Frictional contact area
What are the risks of working with brake fluid?
Which of the following statements about drum
brake shoes is not true?
a. Linings may be riveted or bonded to the shoes.
b. Shoe indentions hold the shoe in place
against the backing plate.
c. The shoe rim supports the shoe lining.
d. The primary/leading shoe is typically the one
that is positioned toward the front of the
vehicle.
Chapter 50 Solutions
Automotive Technology
Ch. 50 - Explain why bleeding air out of a hydraulic system...Ch. 50 - Explain why modern hydraulic braking systems are...Ch. 50 - Describe the functions of the hydraulic system...Ch. 50 - When the brakes are applied on a moving car, the...Ch. 50 - What is the purpose of the master cylinder vent...Ch. 50 - Explain why a height-sensing proportioning valve...Ch. 50 - A three-function combination valve has a brake...Ch. 50 - Explain how vacuum is used to provide a power...Ch. 50 - True or False? Metering and proportioning valves...Ch. 50 - True or False? Semimetallic brake pads still often...
Ch. 50 - The purpose of the master cylinder is to. generate...Ch. 50 - Which of the following can lead to brake hose...Ch. 50 - Which type of brake requires greater application...Ch. 50 - Which of the following is not a factor in...Ch. 50 - Which of the following could cause an extremely...Ch. 50 - A vehicles power brakes are grabbing: Technician A...Ch. 50 - While discussing what affects the amount of...Ch. 50 - The metering valve portion of a combination valve...Ch. 50 - While discussing quick take-up master cylinders:...Ch. 50 - While bleeding a brake system: Technician A...Ch. 50 - The basic frictional parts of a brake system are...Ch. 50 - Vehicle dynamics during braking are being...Ch. 50 - Pressure bleeding is being discussed: Technician A...Ch. 50 - Technician A says that the master cylinder should...Ch. 50 - The hydraulic system of the hydro-boost and...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- True or False? If brake fluid is discolored, the system must be flushed and the fluid replaced.arrow_forwardTrue or False? Backing plates, struts, levers, and other metal brake parts should be cleaned with a wet-cleaned using water or a water-based solution.arrow_forwardWhich of the following is not a suitable way to bleed an entire hydraulic brake system? Manual bleeding Bench bleeding Pressure bleeding Vacuum bleedingarrow_forward
- True or False? If brake fluid is dark or brown colored. the system must be flushed and the fluid replaced.arrow_forwardBrake linings should be replaced when. linings are worn to within */3 inch of a rivet head linings are contaminated with oil or grease linings are contaminated with brake fluid all of the abovearrow_forwardWhich of the following is not a factor in determining the effectiveness of a brake system? Heat dissipation Lubricant Pressure Frictional contact areaarrow_forward
- Backing plates, struts, levers, and other metal brake parts should be. wet-cleaned using water or a water-based solution wet-cleaned using an alcohol-based solvent wet-cleaned using gasoline dry-cleaned onlyarrow_forwardAsbestos has not been used in brake linings or pads since 2003. a. True b. False Technician A says low-drag calipers retract the pistons and pads farther from the rotor than traditional calipers. Technician B says systems that use low-drag calipers cannot use quick take-up master cylinders. Who is correct? a. A only b. B only c. both A and B d. neither A nor B A brake line must be single-flared to provide a good seal at a joint or junction block. a. True b. False Vehicles use brake pedal position sensors. a. True b. Falsearrow_forwardWhich of the following is true about a brake service? A. It should always include a comprehensive brake inspection B. It requires specialized tools. C. It may lead to additional work if performed properly. C. All of the abovearrow_forward
- After resurfacing a brake drum: Technician A cleans it using hot water and a lint-free cloth. He then uses compressed air to thoroughly dry it Technician B cleans the drum using a lint-free cloth dipped in a special brake cleaning solvent. She then allows the drum to dry before reinstallation. Who is correct? Technician A only Technician B only Both A and B Neither A nor Barrow_forwardTrue or False? Semimetallic brake pads still often are made with asbestos.arrow_forwardTrue or False? Metering and proportioning valves balance the braking characteristics of disc and drum brakes.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Mechanical Design (Machine Design) Clutches, Brakes and Flywheels Intro (S20 ME470 Class 15); Author: Professor Ted Diehl;https://www.youtube.com/watch?v=eMvbePrsT34;License: Standard Youtube License