What is the job of wheel cylinder stops?

Q: anism?

A: Inversions of mechanism: A mechanism is one wherein one of the hyperlinks of a kinematic chain is…

Q: List the missing parts Reciprocating motion Crank mechanism

A: A connecting rod in the engine is used to connect the piston with the crank rod. one end is attached…

Q: Define Straddle hubs.

A: A straddle is a trading strategy that involves options.

Q: Where does maximum cylinder bore wear occur and why

A: Cylinder bore wear occurs due to continuous piston movement in the cylinder. Wear can be seen only…

Q: how will a vehicle handle if it has too much toe-out?

A:

Q: Brake power output of the engine ?

A: Given; The indicated power developed by an engine with compressionratio,r=8It is calculated using an…

Q: crankshaft

A: Statement is true

Q: With neat sketch explain the crank and slotted mechanism?

A: The crank and slotted lever mechanism is a quick return mechanism in which forward strokes are…

Q: Before installing the crankshaft, what should you spray onto the bearings?

A: Before installing the crankshaft the chemical treatment by using oil and grease is required to be…

Q: what pushes the baulk ring into the cone on the gear when the sleeve  start to move on the hub ?

A: What pushes the baulk ring into the cone on the gear when the sleeve start to move on the hub

Q: When discussing shift problems, Technician A says that worn or broken engine and transaxle mounts…

A: A chain of gears which is used to pass on the power to the wheel from the engine is called as…

Q: Technician A says that a cylinder wall with too smootha surface will prevent the piston rings from…

A: Rings won't seat properly and will instead "skate" across the surface if the cylinder walls are…

Q: what parts provide for toe-out on turns

A: Toe-out on turns is a toe setting for the front wheels so that it can make turns. While making a…

Q: A locomotive in which the driving wheels are connected to leading and trailing wheels is called as…

A: Given: A locomotive in which the driving wheels are connected to leading and trailing wheels is…

Q: The connecting rod journal is also called the __ .a. balancer shaftb. vibration damperc.…

A:

Q: What is the correct sequence for adjusting alignmentangles during a four-wheel alignment?

A: Given Data : Adjusting alignment angles during four wheel alignment.

Q: Which type of driving axle supports the weightof the vehicle?a. Semifloatingb. Three-quarter…

A: Semi-floating type axle: This design contains one wheel support bearing mounted on the outer end of…

Q: Worn teeth on a speed gear can cause?

A: worn teeth creates a big problem in gear drive.

Q: Technician A says that broken or worn engine and transaxle mounts can cause a transaxie to have…

A: Given Transaxle problem To find Statement with is/are correct Shifting problem of transaxle can be…

Q: What does the internal torque produce?

A:

Q: displacement (throw) of the wheel assembly.

A:

Q: Analytically determine the range of transmission angle crank blade

A:

Q: The fuction of fly wheel is to a. store energy during all strokes of engine. b. store energy during…

A: A Flywheel  is a mechanical device that is used to store rotational energy.

Q: Where are the application of slider crank mechanism?

A: This question is based on the concept of slider crank mechanism.

Q: nance pr Tollowed wniie performing gib adjustment on a lathe machine is O On the front face of the…

A:

Q: 128) Technician A says slide hammer pullers are usually required to remove the front pump from the…

A: A slide hammer puller is a mechanical tool with a long round shaft. It has a hammer weight slides. A…

Q: The four common configurations used as the finaldrives on FWD vehicles are the __ gear, __ gear,__…

A: The four often utilized final drive designs for FWD cars are chain drive, hypoid gear, planetary…

Q: al cup of equired to pach job f 240 cc ecificatio

A: Given: The radius of hemispherical cup is 15cm The force required to deform is 8KN. The approach…

Q: Name the 4 strokes of four-cylinder engine?

A:

Q: what changes were made to master cylinder when the cylinder cups were changed to…

A: Master cylinder is the mechanical component that we use in the braking system. It converts the force…

Q: Instructions: Identify the wheel cylinder parts in the drawing. Place the identifying letter next to…

A: Cup - C  Cylinder - D  Piston - B

Q: flyw

A: compare governor and flywheel

Q: Helical gear

A: Ans is Helical gear

Q: Mobility of a triple crank mechanism is one O four O two three

A: Mobility of triple crank mechanism is one

Q: of the link is havi

A: given: Which of the link is having to and fro movement in the engine mechanism? crank…

Q: When removing or installing bearing, where should force be applied

A: The application of force during installation or removal of bearing is one of the critical factors,…

Q: 8.Which of the following pairs is high pair? A sliding pair В cam pair C screw pair

A: Higher pair: When the two elements have point or line contact while in motion then the pair is known…

Q: Where is the rod end of the cylinder?

A: Given: To identify the rod end of cylinder.

Q: The knocking is usually occurred at the low engine speed O a. True O b. False

A: True

Q: What type of caps are used to hold the crankshaft in place once it’s installed in the block?

A: Crankshaft is a shaft used in engine to convert a linear motion of piston to a rotational motion. It…

Q: why is it necessary to purify crankcase lubricating oil and how is the purification done

A: The partition of impurities and water from fuel oil is basic for great combustion. The evacuation…

Q: What type of axle housing resembles a banjo?

A: Given Data : Banjo

Q: the ... motion of the pistons is converted into the ... motion of the crankshaft

A: An IC engine consists of many parts such as Piston, crankshaft, connecting rod, Cylinder, Crank…

Q: What safety precautions must be observed when carrying out diagnosing procedure on drive shafts?

A: Depending on the performance outcome, the correct diagnose required in the drive shaft of the light…

Q: Why is it important to loosen the cylinder head bolts in the recommended order

A: Cylinder heads have different shapes and configurations, each possesses their specific procedure to…

Q: The clutch, or friction, disc is connected to the

A: The clutch, or friction, disc is connected to the....

Q: P -P -8 in. -8 in.- (a) (b) /hich of the following best explains why cylinder (b) har a binh

A: Given: Which of the following best explains why cylinder (b) has higher longitudinal stress in its…

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.