Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 52, Problem 10ASRQ
Loaded calipers are being discussed: Technician A says that loaded calipers are replacement calipers that come with pads and hardware already installed. Technician B says that loaded calipers should always be installed in axle sets. Who is correct?
- Technician A only
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Technician A says that fixed calipers use a piston oneach side of the rotor to apply the brakes. Technician Bsays that sliding calipers typically use only one pistonor pistons on one side of the rotor. Who is correct?a. Technician A onlyb. Technician B onlyc. Both A and Bd. Neither A nor B
When replacing brake pads on a vehicle: Technician A works on one wheel before beginning work on an-other. Technician B uses a minimum of 52 psi of air pressure to force the piston from the caliper housing. Who is correct?
Technician A says that on most vehicles, the wheel/tire assembly is considered sprung weight . Technician B says that low unsprung weight makes the vehicle handle better on irreg ular surfaces. Who is correct?
Chapter 52 Solutions
Automotive Technology
Ch. 52 - Name the three major assemblies that make up a...Ch. 52 - Name the three types of calipers used on disc...Ch. 52 - Describe the differences between floating and...Ch. 52 - What is the difference between floating and...Ch. 52 - What is rotor parallelism and how is it checked?Ch. 52 - Why is brake fluid removed from the master...Ch. 52 - Describe the procedure for using compressed air to...Ch. 52 - List three conditions that dictate that a rotor...Ch. 52 - Give two main advantages of an on-vehicle lathe...Ch. 52 - What should be done to remove rust, corrosion, pit...
Ch. 52 - What type of brake uses the inside of each rear...Ch. 52 - True or False? Disc brakes are not as likely to...Ch. 52 - True or False? All calipers have at least one...Ch. 52 - Which term refers to variations in thickness of...Ch. 52 - Which of the following is not likely to cause a...Ch. 52 - Technician A says that a hard brake pedal on a...Ch. 52 - When replacing brake pads on a vehicle: Technician...Ch. 52 - When examining disc brakes: Technician A visually...Ch. 52 - When reassembling an overhauled brake caliper:...Ch. 52 - While discussing how to remove the piston from a...Ch. 52 - The functions of a splash shield are being...Ch. 52 - Technician A says that the piston seal retracts...Ch. 52 - Technician A says that fixed calipers use a piston...Ch. 52 - While installing new brake pads: Technician A...Ch. 52 - Loaded calipers are being discussed: Technician A...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Technician A says that fixed calipers use a piston on each side of the rotor to apply the brakes. Technician B says that sliding calipers typically use only one piston or pistons on one side of the rotor. Who is correct? Technician A only Technician B only Both A and B Neither A nor Barrow_forwardWhile diagnosing the cause of a clicking noise that is heard only when the car is turning: Technician A says that the most probable cause is a worn wheel bearing. Technician B says that the most probable cause is a worn outboard CV joint. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardWhich of the following statements about drum brakeshoes is not true?a. Web thickness varies only with changes in shoesize.b. Many shoes have indented places along the edgeof the rim.c. The shoe rim is welded to the web.d. The primary/leading shoe is typically the one thatis positioned toward the front of the vehiclearrow_forward
- Technician a says radial ply tires are more rigid in the sidewall area than bias ply tires. Technician b says the belts in a radial tire restrict tread motion during contact with the road thus improving tread life in traction. who is correctarrow_forwardTechnician A says the front wheel bearings on a typical FWD car are sealed and non-adjustable. Technician B says the front wheel bearings on a typical FWD car are greaseable and adjustable. Who is correct?arrow_forwardTechnician A says that flare nut or line wrenches should be sued to loosen or tighten brake line or tubing fittings Technician B says that open-end wrenches will surround the fitting's nut and provide a positive grip on the fitting. Who is correct? Group of answer choices Technician A only Technician B only Both Technicians A and B Neither A nor Barrow_forward
- When replacing brake pads on a vehicle: Tech-nician A works on one wheel before beginning work on another. Technician B uses a minimum of 52 psi of air pressure to force the piston from the caliper housing. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardWhile discussing proper band adjustment procedures: Technician A says that on some vehicles the bands can be adjusted externally with a torque wrench. Technician B says that a calibrated inch- pound torque wrench is normally used to tighten the band adjusting bolt to a specified torque. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardWhile discussing the effects of overtorquing wheel lugs: Technician A says that this can cause the threads of the lugs and/or studs to distort. Technician B says that this can cause disc brake rotor distortion. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- All calipers have at least one piston that pushes the brake pad against the rotor?arrow_forwardTechnician A says that the front bearing assembly locknuts for RWD vehicles are typically heavily torqued to maintain the bearing adjustment. Technician B says that the axle nuts for FWD wheel bearing assembly is often staked in place to maintain its specified torque. Who is correct?arrow_forwardInjuries in a workshop are often caused by incorrect lifting or moving of heavy loads. Name and briefly explained two (2) precautions that should be taken when removing a gearbox from a vehicle on a hoist.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Mod-01 Lec-16 Basics of Instrumentation; Author: nptelhrd;https://www.youtube.com/watch?v=qbKnW42ZM5c;License: Standard YouTube License, CC-BY