Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 53, Problem 12RQ
When inspecting wheel-speed sensors, check for all of the following except
- buildup of metal or rust on the sensor.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Wheel speed sensors provide different output, name the different types of sensors and describe their output?
Technician A says that on FWD vehicles, the front wheels toe-out while the rear wheels on an independent suspension try to toe-in as the vehicle moves ahead. Technician B says that on RWD vehicles, the front wheels tend to toe-in while the rear wheels toe-out in response to rolling resistance as suspension compliance. Who is correct?
the air gap between the crankshaft position sensor measured with and the trigger wheel is measured with an?
Chapter 53 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 53 - What is the primary difference between an...Ch. 53 - Briefly describe the proper steps and testing...Ch. 53 - An ABS modulates brake pressure. What does this...Ch. 53 - Explain the difference between over steer and...Ch. 53 - List the various methods used by traction control...Ch. 53 - Besides indicating ABS faults for some systems,...Ch. 53 - What are the functions of an isolation/dump valve?Ch. 53 - Describe the normal pedal feel when the ABS is...Ch. 53 - Which of the following is a true statement? In...Ch. 53 - What is the name for the gas-filled pressure...
Ch. 53 - What four things should be checked before...Ch. 53 - When inspecting wheel-speed sensors, check for all...Ch. 53 - Define the difference between an integrated and a...Ch. 53 - What is the basic difference between a Delco ABS...Ch. 53 - Why are the wires leading to some wheel-speed sen...Ch. 53 - Technician A says that a malfunction of the ABS...Ch. 53 - While road testing a car equipped with an ABS:...Ch. 53 - Technician A says that the accumulator in an ABS...Ch. 53 - Technician A says that it is normal for the amber...Ch. 53 - Technician A says that some antilock brake systems...Ch. 53 - Technician A says that wheel-speed sensors send an...Ch. 53 - Technician A says that an ABS problem can cause...Ch. 53 - Technician A says that each ABS has its own...Ch. 53 - When removing a vehicles ABS electronic control...Ch. 53 - Technician A says that some traction control...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A 3-degree difference in the SAI angle on each side of the front suspension may cause a FWD vehicle to have increased during hard acceleration.arrow_forwardTrue or False? On some engines, if the gap between the crankshaft sensor and its trigger wheel is outside specifications, the sensor should be replaced.arrow_forwardDescribe the differences between passive and active wheel speed sensors.arrow_forward
- Explain about sensors using for speed, throttle position and crank shaft position with the help of neat diagram.arrow_forwardWhile discussing the fail-safe function: Technician A says that the 4WS indicator light is illuminated during the fail-safe function. Technician B says that the rear wheels steer normally when the 4WS control unit enters the fail-safe mode. Who is correct?arrow_forwardWhich of the following is the most likely cause of a lean condition during acceleration and cruising speeds? a. A defective oxygen sensor b. A defective PCM c. A defective ECT sensor d. A defective MAF sensorarrow_forward
- True or False? Some crankshaft and camshaft timing sensors have a specified gap that must be set during installation.arrow_forwardTechnician A says that wheel-speed sensors send an AC voltage signal to the control module. Technician B says that wheel speed signals create an AC signal voltage by altering a reference voltage received from the control module. Who is correct? Technician A only Technician B only Both A and B Neither A nor Barrow_forwardDescribe the two basic types of passenger weightdetection sensors used in most vehiclesarrow_forward
- List the various methods used by traction control systems to eliminate wheel spin.arrow_forwardExplain the operation of the accelerator position sensors?arrow_forwardTechnician A says that some antilock brake systems use a lateral acceleration sensor in addition to the wheel-speed sensors. Technician B says that traction control systems apply one wheel brake to get the vehicle going in the direction in which it is being steered. Who is correct? Technician A only Technician B only Both A and B Neither A nor Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Mod-01 Lec-16 Basics of Instrumentation; Author: nptelhrd;https://www.youtube.com/watch?v=qbKnW42ZM5c;License: Standard YouTube License, CC-BY