![MindTap Engineering for Das/Sobhan's Principles of Geotechnical Engineering, 9th Edition, [Instant Access], 2 terms (12 months)](https://s3.amazonaws.com/compass-isbn-assets/textbook_empty_images/large_textbook_empty.svg)
MindTap Engineering for Das/Sobhan's Principles of Geotechnical Engineering, 9th Edition, [Instant Access], 2 terms (12 months)
9th Edition
ISBN: 9781305971257
Author: Braja M. Das; Khaled Sobhan
Publisher: Cengage Learning US
expand_more
expand_more
format_list_bulleted
Question
Chapter 6, Problem 6.16P
To determine
Find the significant depth of densification.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
The coefficient of permeability of a sand at a void ratio of 0.62 is 0.03 cm/sec. estimate the
coefficient of permeability at a void ratio of 0.48.
a. Using Casagrande equation
b. Using kozeny - Carman equation.
Show solution. The answer must be 8.22 x10^-10 ft/sec
Repeat Problem 16.6 with the following:D50 = 3.2 mmD20 = 0.91 mmD10 = 0.72 mm
Chapter 6 Solutions
MindTap Engineering for Das/Sobhan's Principles of Geotechnical Engineering, 9th Edition, [Instant Access], 2 terms (12 months)
Knowledge Booster
Similar questions
- A sand has Gs = 2.66. Calculate the hydraulic gradient that will cause boiling for e = 0.35, 0.45, 0.55, 0.7, and 0.8.arrow_forwardThe total density of sand in an embankment was found to be 1900kg/m^3 and the field water content was 12% . In the laboratory, the density of the solid was found to be 2660 kg.m^3, and the maximum and minimum voids ratio were 0.63 and 0.44, respectively What is the void ratio of the sand? Calculate the relative density of the sand in the field:arrow_forwardA large oil storage tank 90 meters in diameter is to be constructed on the soil profile shown in the figure below. The average depth of the oil in the tank is 18 meters, and the specific gravity of the oil is 0.92. Consolidation test showed that the clay is normally consolidated with Ccε = 0.154, Crε = 0.0112, and σ'p = 260 kPa. Estimate the total consolidation settlement of the tank. Neglect any settlements in the sand (ρd,sand = 1.71 Mg / m3). Perform this estimation by: a. Assuming conditions at the mid-depth of the clay are typical of the entire clay layer. b. Dividing the clay layer into four thinner layers with a thickness of 5 meters each, computing the settlement of each thin layer, and summing up using the included equation for sc. Assume that σ'p = σ'vo when σ'vo > σ'p. Hint: the load applied by the tank is given by qo = ϒoilhoilarrow_forward
- For a laboratory consolidation test on a clay specimen (drained both sides), the following were obtained. Thickness of the clay layer = 25mm o_1 = 200KN/m^2 o'2 = 400KN/m^2 e_1 = 0.73 e_2 = 0.61 Time for 50% consolidation (t_50 = 2.8min: From table U = 50%, Tv = 0.197 %3D Determine the hydraulic conductivity (in cm/sec) of the clay for the loading range.arrow_forwardplease answer 2 and 3arrow_forwardQuestion attachedarrow_forward
- Need asap pls. Thanks.arrow_forwardW1arrow_forwardThe results of a laboratory consolidation test on a clay sample are given below: Pressure, p (kN/m²) Void ratio, e 23.94 1.112 47.88 1.105 95.76 1.080 191.52 0.985 383.04 0.850 766.08 0.731 (43) a) Draw an e-log p plot. (44) b) Determine the pre-consolidation pressure, p. . (45) c) Find the compression index, Ce. Appendix For ø=35°, N¸=57.8, N,=41.4, and N,=41.1. o,'=0;'tan²| 45°+ +2c tan| 45°+arrow_forward
- 4.15 The following results were obtained from a liquid limit test on a clay using the Casagrande cup device. Number of blows 6 12 20 28 32 Water content (%) 52.5 47.1 43.2 38.6 37.0 (а) Determine the liquid limit of this clay. (b) If the natural water content is 38% and the plastic limit is 23%, calculate the liquidity index. (c) Do you expect a brittle type of failure for this soil? Justify your answer.arrow_forwardSolve correctarrow_forwardThe results of a laboratory consolidation test on a clay specimen are the following. Pressure, ir (lb/ft²) 500 1.000 2.000 4.000 8,000 16.000 Total height of specimen at end of consolidation (in.) 0.6947 0.6850 0.6705 0.6520 0.6358 0.6252 Given the initial height of specimen = 0.748 in.. G specimen = 95.2 g. and area of specimen = 4.91 in.²: a. Plot the e-log or curve = 2.68. mass of dry b. Determine the preconsolidation pressure c. Calculate the compression index, C.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Geotechnical Engineering (MindTap C...Civil EngineeringISBN:9781305970939Author:Braja M. Das, Khaled SobhanPublisher:Cengage Learning
Fundamentals of Geotechnical Engineering (MindTap...Civil EngineeringISBN:9781305635180Author:Braja M. Das, Nagaratnam SivakuganPublisher:Cengage Learning
Principles of Foundation Engineering (MindTap Cou...Civil EngineeringISBN:9781305081550Author:Braja M. DasPublisher:Cengage Learning
Principles of Geotechnical Engineering (MindTap C...
Civil Engineering
ISBN:9781305970939
Author:Braja M. Das, Khaled Sobhan
Publisher:Cengage Learning
Fundamentals of Geotechnical Engineering (MindTap...
Civil Engineering
ISBN:9781305635180
Author:Braja M. Das, Nagaratnam Sivakugan
Publisher:Cengage Learning
Principles of Foundation Engineering (MindTap Cou...
Civil Engineering
ISBN:9781305081550
Author:Braja M. Das
Publisher:Cengage Learning