Fundamentals of Aerodynamics
Fundamentals of Aerodynamics
6th Edition
ISBN: 9781259129919
Author: John D. Anderson Jr.
Publisher: McGraw-Hill Education
bartleby

Concept explainers

bartleby

Videos

Textbook Question
Book Icon
Chapter 7, Problem 7.1P

Note: In the following problems, you will deal with both the International System of Units (SI) (N, kg, m, s, K) and the English Engineering System (lb, slug, ft, s, ° R ). Which system to use will be self-evident in each problem. All problems deal with calorically perfect air as the gas, unless otherwise noted. Also, recall that 1 atm = 2116 lb/ft 2 = 1.01 × 10 5 N/m 2 .

The temperature and pressure at the stagnation point of a high-speed missile are 934  ° R and 7.8 atm, respectively. Calculate the density at this point.

Expert Solution & Answer
Check Mark
To determine

The density of missile at the stagnation point.

Answer to Problem 7.1P

The density of missile at stagnation point is ρo=0.0103slug/ft3

Explanation of Solution

Given Information:

  Pressure of missile at stagnation point is, Po=7.8atmTemperature of missile at stagnation point is, To=934°RThe gas constant is Btu is, R=1716ft.lb/(slug.°R)

Calculation:

From ideal gas equation, the density at the given point can be calculated as,

  Po=ρoRToρo=PoRToPlugging R=1716ft.lb/(slug°R),To=934°R&Po=7.8atmρo=7.8( atm)[1716 ft.lb/ ( slug°R )][934°R]( 2116 lb/ ft 2 1atm)ρo=0.0103slug/ft3

Hence, the density of missile at the stagnation point is ρo=0.0103slug/ft3

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
The clear plastic bottles used for carbonated beverages (sometimes also called “soda,” “pop,” or “soda pop”) are made from poly(ethylene terephthalate) (PET). The “fizz” in pop results from dissolved carbon dioxide (CO2); because PET is permeable to CO2, pop stored in PET bottles will eventually go “flat” (i.e., lose its fizz). A 20-oz. bottle of pop has a CO2 pressure of about 570 kPa inside the bottle, and the CO2 pressure outside the bottle is 7 kPa. Assuming conditions of steady-state, calculate the diffusion flux in cm3 at STP/cm2.s of CO2 through the wall of the bottle. The Permeability Constant of the PET bottle is 0.23 x 10^-13 cm3@STP.cm/cm2.s.Pa. Note: assume that each bottle has a surface area of 500 cm2 and a wall thickness of 0.07 cm. Answer in Scientific Notation example 1.1e-12. Round your answer to 2 significant figures.
The clear plastic bottles used for carbonated beverages (sometimes also called “soda,” “pop,” or “soda pop”) are made from poly(ethylene terephthalate) (PET). The “fizz” in pop results from dissolved carbon dioxide (CO2); because PET is permeable to CO2, pop stored in PET bottles will eventually go “flat” (i.e., lose its fizz). A 20-oz. bottle of pop has a CO2 pressure of about 485 kPa inside the bottle, and the CO2 pressure outside the bottle is 0.6 kPa. The Permeability Constant of the PET bottle is 0.23 x 10^-13 cm3@STP.cm/cm2.s.Pa. Note: assume that each bottle has a surface area of 500 cm2 and a wall thickness of 0.07 cm. If the bottle must lose 750 (cm3 STP) of CO2 before the pop tastes flat, what is the shelf life in days for a bottle of pop? Round your answer to 0 decimal places.
During the fall of 2005, Hurricane Wilma passed through the Gulf of Mexico. When the storm was classified as a category 5 hurricane, the pressure at the center of the hurricane was measured at 902 mbars. The highest wind velocity was 175 mph. Assuming the pressure far from the center of the hurricane was 1 bar and the air density was 1.2 kg m3 , estimate the pressure at the center of the hurricane. Comment on the difference in your prediction and the measured value and provide some rationale for the discrepancy. The answer should be p = 914 mbar

Additional Engineering Textbook Solutions

Find more solutions based on key concepts
Knowledge Booster
Background pattern image
Mechanical Engineering
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.
Similar questions
SEE MORE QUESTIONS
Recommended textbooks for you
Text book image
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Text book image
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Text book image
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Text book image
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Text book image
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Text book image
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
First Law of Thermodynamics, Basic Introduction - Internal Energy, Heat and Work - Chemistry; Author: The Organic Chemistry Tutor;https://www.youtube.com/watch?v=NyOYW07-L5g;License: Standard youtube license