A rectangular plate (0 =25°) is formed by welding two triangular plates shown in figure. The plate is subjected to a compressive stress of 2.5 MPa in the x-direction and a tensile stress of 15 MPa in the y-direction. Determine the normal stress acting perpendicular to the line of the weld and the shear stress acting parallel to the weld. Weld Lütfen birini seçin: a. 0.6256 MPa/6.70 MPa b. None O c. 11.874 MPa/6.70 MPa O d. 9.3175 MPa/6.09 MPa O e. 0.417 MPa/4.38 MPa

A rectangular plate (0 =25°) is formed by welding two triangular plates shown in figure. The plate is subjected to a compressive stress of 2.5 MPa in the x-direction and a tensile stress of 15 MPa in the y-direction. Determine the normal stress acting perpendicular to the line of the weld and the shear stress acting parallel to the weld. Weld Lütfen birini seçin: a. 0.6256 MPa/6.70 MPa b. None O c. 11.874 MPa/6.70 MPa O d. 9.3175 MPa/6.09 MPa O e. 0.417 MPa/4.38 MPa

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.26P: -26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and...

See similar textbooks

Similar questions

Two steel rods are welded together (see figure): the seam is oriented at angle ? = 50°. The stresses on the rotated element are sx1=10 ksi, sy1= -12 ksi, and tx1y1= -5 ksi. Find the state of plane stress on the clement if it is rotated clockwise to align the x3 axis with the longitudinal axis of the rods.
-26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and compressive stress a. If it is known that the normal stress along the diagonal t—t is ??t= -6.57 kPa, find stress ??y on element A. a
The polyethylene liner of a settling pond is subjected to stresses ax= 350 psi. a = 112 psi. and = -120 psi, as shown by the plalte-stress element in the figure part a. Determine the normal and shear stresses acting on a seam oriented at an angle 01300 to the element, as shown in the figure part b. Show these stresses on a sketch of an element having its sides parallel and perpendicular to the seam.
Solve the preceding problem for an element in plane stress on the bottom surface of a fuel tanker (figure part a); stresses are sx= 105 MPa, sy. = 75 MPa, and ??xy= 25 MPa. Determine the stresses acting on an element oriented at an angle ?? = 40° from the x axis, where the angle is positive when counterclockwise. Show these stresses on a sketch of an element oriented at the angle ??.
A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
At a point on the web of a girder on an overhead bridge crane in a manufacturing facility, the stresses arc known to be x = —4300 psi, a = 1700 psi, and r = 3100 psi (the sign convention for these stresses is shown in Fig, 7-1). A stress clement located at the same point in the structure (but oriented at a counterclockwise angle 0, with respect to the _y axis) is subjected to the stresses shown in the figure {b, r», and 2100 psi). Assuming that the angle 8Xis between zero and 90°, calculate the normal stress trA, the shear stress ta, and the angle Bv
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
A punch for making a slotted hole in ID cards is shown in the figure part a. Assume that the hole produced by the punch can be described as a rectangle (12 mm X 3 mm) with two half circles (r = 1.5 mm) on the left and the right sides. If P = 10 N and the thickness of the ID card is 1 mm, what is the average shear stress in the card?
An element on the top surface of the fuel tanker in Problem 7.2-1 is in biaxial stress and is subjected to stresses a = -48 MPa and ay = 19 MPa, as shown in the figure. Using Mohr’s circle, determine the following. (a) The stresses acting on an clement oriented at a counterclockwise angle ?? = 25° from the x axis. (b) The maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements.
Two boards are joined by gluing along a scarf joint, as shown in the figure. For purposes of cutting and gluing, the angle a between the plane of the joint and the faces of the boards must be between 10° and 40f. Under a tensile load P, the normal stress in the boards is 4.9 MPa. (a) What axe the normal and shear stresses acting on the glued joint if a = 20°? (b) If the allowable shear stress on the joint is 2.25 MPa. what is the largest permissible value of the angle ct? (c) For what angle a with the shear stress on the glued joint be numerically equal to twice the normal stress on the joint?
: A cylindrical tank with diameter d = 18 in, is subjected to internal gas pressure p = 450 psi. The tank is constructed of steel sections that arc welded circum fereiitially (sec figure). The heads of the tank are hemispherical. The allowable tensile and shear stresses are 8200 psi and 3000 psi, respectively. Also, the allowable tensile stress perpendicular to a weld is 6250 psi. Determine the minimum required thickness /minof (a) the cylindrical part of the tank and (b) the hemispherical heads.
-27 A square plate with side dimension of 2 in. is subjected to compressive stress a and tensile stress The stresses on element A oriented at angle ?? x1=45° aresy1= 75 psi. tx1y1= 275 psi. . Find the state of stress on the element lilt is rotated clockwise to align the x3 axis with the horizontal x axis.