Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 8, Problem 25RQ
How does a technician determine the proper inflation for a vehicle's tires?
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
An indirect TPMS is being discussed. Technician A says that if a specific tire is low, the system will typically alert the driver which tire is low. Technician B says that after serving the indirect TPMS, you need to perform a re-learn procedure. Who is correct?
Technician A
Technician B
Both Technician A and B
Neither Technician A or B
Technician A says the front wheel bearings on a typical FWD car are sealed and non-adjustable. Technician B says the front wheel bearings on a typical FWD car are greaseable and adjustable. Who is correct?
what is the formula to measure gas from tire interior?
Chapter 8 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 8 - Describe the information found in a VIN.Ch. 8 - Technician A stresses the need to follow the...Ch. 8 - Prob. 3RQCh. 8 - Prob. 4RQCh. 8 - True or False? Legally, an RO protects the shop...Ch. 8 - While examining the color of an engines coolant:...Ch. 8 - While checking the condition of a vehicles ATF:...Ch. 8 - Technician A says that if a drive belt does not...Ch. 8 - List five different types of oil rating systems.Ch. 8 - Technician A says that to accurately check brake...
Ch. 8 - Why should you wipe off the outside of a zerk...Ch. 8 - True or False? All engine coolants contain some...Ch. 8 - List at least five things that should be checked...Ch. 8 - True or False? If brake fluid is dark or brown...Ch. 8 - Which of the following statements about drive belt...Ch. 8 - Prob. 16RQCh. 8 - Which of the following statements about an oils...Ch. 8 - While discussing a vehicles maintenance program:...Ch. 8 - Which of the following is not a true statement...Ch. 8 - True or False? An oil with the classification of...Ch. 8 - While discussing the effects of overtorquing wheel...Ch. 8 - The most commonly used brake fluid in domestic...Ch. 8 - Which of the following greases are best suited for...Ch. 8 - While discussing the special preventive...Ch. 8 - How does a technician determine the proper...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- While diagnosing the cause of noise from a transfer case: Technician A says that a probable cause is incorrect tire size. Technician B says that the most probable cause is a faulty bearing or gear. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardTechnician A says that replacement wheel rims should be the same as the original equipment wheels in load capacity, offset, width, diameter, and mounting configuration. Technician B says that if wheels are installed that have a different stock width or diameter, make sure to use a tire that has the same overall width as the original tires. Otherwise the vehicles wheel-speed sensors, speedometer, antiock brake system, and many other systems will be affected. Who is correct? a. Technician A only b. Technician B only c. Both A and B Neither A nor Barrow_forwardWhile discussing pull during braking: Technician A says that this can be caused by one tire being underinflated. Technician B says that a frozen wheel cylinder on one side of the car can cause this. Who is correct? Technician A only Technician B only Both A and B Neither A nor Barrow_forward
- All of the following statements are correct except? a. Tire inflation pressure directly affects traction. b. The recommended tire pressure for front and rear tires may be different. c. The recommended tire pressures are often lower than maximum pressures. d. The recommended tire pressure is molded into the sidewall of the tire.arrow_forwardRepair work performed on vehicles still under tire manufacturers warranty is usually performed by independent service shops dealerships specialty shops either a or barrow_forwardTrue or False? Make sure you locate and adhere to the wet torque specs when tightening a bolt that has been lubricated with oil or any other liquid.arrow_forward
- Technician A says that the transmission rear seal at the driveline is particularly prone to leakage. When Technician B pushes up and down on the transmission, he says that the mounts require replacement because the case moves up and down. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardAll of the following statements are correct except?a. Tire inflation pressure directly affects traction.b. The recommended tire pressure for front andrear tires may be different.c. The recommended tire pressures are oftenlower than maximum pressures.d. The recommended tire pressure is moldedinto the sidewall of the tirearrow_forwardTechnician a says radial ply tires are more rigid in the sidewall area than bias ply tires. Technician b says the belts in a radial tire restrict tread motion during contact with the road thus improving tread life in traction. who is correctarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
The Most Common Metal Machining Processes (Metal Machining Video 1); Author: Sofeast Ltd;https://www.youtube.com/watch?v=uxVJ3qtezGw;License: Standard YouTube License, CC-BY
Machining process and Machine Tools; Author: Amar Gandhi;https://www.youtube.com/watch?v=X2mUJ8baaE0;License: Standard Youtube License