Thermodynamics: An Engineering Approach
Thermodynamics: An Engineering Approach
9th Edition
ISBN: 9781259822674
Author: Yunus A. Cengel Dr., Michael A. Boles
Publisher: McGraw-Hill Education
bartleby

Concept explainers

bartleby

Videos

Question
Book Icon
Chapter 8.8, Problem 120RP
To determine

The change in the work potential of the air stored in the tank.

The change in exergy of the air stored in the tank.

Expert Solution & Answer
Check Mark

Answer to Problem 120RP

The change in the work potential of the air stored in the tank is 3.516×108kJ.

The change in exergy of the air stored in the tank is 7.875×108kJ.

Explanation of Solution

Write the formula to calculate initial mass of air in the tank (mi).

mi=PiVRTi (I)

Here, initial pressure of air is Pi, volume of the tank is V, initial temperature of air is T and gas constant of air is R.

Write the formula to calculate final mass of air in the tank (mf).

mf=PfVRTf (II)

Here, final pressure of air is Pf and final temperature of air is Tf.

Write the formula to calculate temperature of air at state 2 using isentropic relation (T2).

T2=T1(P2P1)k1k

Here, temperature of air at state 1 is T1, specific heat ratio of air is k, pressure of air at state 1 is P1 and pressure of air at state 2 is P2.

Apply the conservation of mass to the tank which gives the following relation.

dmdt=m˙i

Here, rate of change in mass of air is dmdt and initial mass flow rate of air is m˙1.

Write the equation for the rate of heat transfer using the first law of thermodynamics (Q˙).

Q˙=d(mu)dthdmdtQ˙=VcvRdPdtcpT2VRTdPdt

Here, enthalpy of air is h, internal energy of air is u, volume of tank is V, specific heat capacities at constant pressure and constant volume are cp and cv respectively and change in pressure is dP.

From the final temperature equation and multiplying the above relation by dt, it gives,

Q˙dt=VcvRdPcp(T1(P2P1)k1k)VRTdP

Integrate the above relation.

Q=VcvR(PfPi)k2k1cpVR(Pf(PfPi)k1kPi) (III)

Apply the first law to the tank and compressor.

(Q˙W˙out)dt=d(mu)h1dm

Here, rate of work potential of the air stored in the tank is W˙out.

Integrate the above relation.

QWout=mfufmiuih1(mfmi)Wout=Q+(cpcv)T(mfmi) (IV)

Here, change in the work potential of the air stored in the tank is Wout and initial and final internal energies of air are ui and uf respectively.

Apply the first law and second law to the tank and compressor and the mass balance incorporated. It gives,

W˙rev=Q˙(1T0TR)d(UT0ds)dt+(hT0s)dmdt

Here, dead state temperature is T0, rate of reversible work done on the system is W˙rev and change in entropy is ds.

Integrate the above relation.

Wrev=Q(1T0T)+mi[(uih1)T0(sis1)]mf[(ufh1)T0(sfs1)]=Q(1T0T)+mi[Ti(cvcp)]mf[Tf(cvcp)T0RlnPfPi] (V)

Here, reversible work done on the system is Wrev.

Conclusion:

Refer Table A-2, "Ideal-gas specific heats of various common gases", obtain the properties of air at the room temperature.

R=0.287kPam3/kgKcp=1.005kJ/kgKcv=0.718kJ/kgKk=1.4

Substitute 100kPa for Pi, 500,000m3 for V, 0.287kPam3/kgK for R and 20°C for Ti in Equation (I).

mi=(100kPa)(500,000m3)(0.287kPam3/kgK)(20°C)=(100kPa)(500,000m3)(0.287kPam3/kgK)(20+273K)=0.5946×106kg

Substitute 600kPa for Pf, 500,000m3 for V, 0.287kPam3/kgK for R and 20°C for Tf in Equation (II).

mf=(600kPa)(500,000m3)(0.287kPam3/kgK)(20°C)=(600kPa)(500,000m3)(0.287kPam3/kgK)(20+273K)=3.568×106kg

Substitute 100kPa for Pi, 600kPa for Pf, 500,000m3 for V, 0.287kPam3/kgK for R, 1.005kJ/kgK for cp, 0.718kJ/kgK for cv and 1.4 for k in Equation (III).

Q={(500,000m3)(0.718kJ/kgK)0.287kPam3/kgK(600kPa100kPa)1.42(1.4)1(1.005kJ/kgK)(500,000m3)0.287kPam3/kgK((600kPa)(600kPa100kPa)1.411.4100kPa)}=6.017×108kJ

Substitute 6.017×108kJ for Q, 1.005kJ/kgK for cp, 0.718kJ/kgK for cv, 20°C for T, 0.5946×106kg for mi and 3.568×106kg for mf in Equation (IV).

Wout={6.017×108kJ+(1.005kJ/kgK0.718kJ/kgK)(20°C)(3.568×106kg0.5946×106kg)}={6.017×108kJ+(1.005kJ/kgK0.718kJ/kgK)(20+273K)(3.568×106kg0.5946×106kg)}=3.516×108kJ

The negative sign shows that the work is done on the compressor.

Thus, the change in the work potential of the air stored in the tank is 3.516×108kJ.

Substitute 6.017×108kJ for Q, 1.005kJ/kgK for cp, 0.718kJ/kgK for cv, 20°C for Ti,20°C for Tf,20°C for T0,20°C for T, 0.5946×106kg for mi,3.568×106kg for mf 100kPa for Pi, 600kPa for Pf and 0.287kPam3/kgK for R in Equation (V).

Wrev={6.017×108kJ(120°C20°C)+(0.5946×106kg)[(20°C)(0.718kJ/kgK1.005kJ/kgK)](3.568×106kg)[(20°C)(0.718kJ/kgK1.005kJ/kgK)(20°C)(0.287kPam3/kgK)ln600kPa100kPa]}={6.017×108kJ(120+273K20+273K)+(0.5946×106kg)[(20+273K)(0.718kJ/kgK1.005kJ/kgK)](3.568×106kg)[(20+273K)(0.718kJ/kgK1.005kJ/kgK)(20+273K)(0.287kPam3/kgK)ln600kPa100kPa]}=7.875×108kJ

This is the exergy change of the air stored in the tank.

Thus, the change in exergy of the air stored in the tank is 7.875×108kJ.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
Air enters an adiabatic nozzle at 45 psia and 940°F with low velocity and exits at 650 ft/s. If the isentropic efficiency of the nozzle is 85 percent, determine the exit temperature and pressure of the air.
Steam enters an adiabatic turbine steadily at 3 MPa and 400°C and leaves at 50 kPa and 100°C. If the power output of the turbine is 2 MW, determine the isentropic efficiency of the turbine.
Steam enters an adiabatic turbine at 2.5MPa pressure and 450C, and at 60kPa pressure and 100C. comes out. If the power output of the turbine is 3MW, the mass flow and the isentropic efficiency of the turbine calculate.

Chapter 8 Solutions

Thermodynamics: An Engineering Approach

Ch. 8.8 - Prob. 11PCh. 8.8 - Does a power plant that has a higher thermal...Ch. 8.8 - Prob. 13PCh. 8.8 - Saturated steam is generated in a boiler by...Ch. 8.8 - One method of meeting the extra electric power...Ch. 8.8 - A heat engine that receives heat from a furnace at...Ch. 8.8 - Consider a thermal energy reservoir at 1500 K that...Ch. 8.8 - A heat engine receives heat from a source at 1100...Ch. 8.8 - A heat engine that rejects waste heat to a sink at...Ch. 8.8 - A geothermal power plant uses geothermal liquid...Ch. 8.8 - A house that is losing heat at a rate of 35,000...Ch. 8.8 - A freezer is maintained at 20F by removing heat...Ch. 8.8 - Prob. 24PCh. 8.8 - Prob. 25PCh. 8.8 - Prob. 26PCh. 8.8 - Can a system have a higher second-law efficiency...Ch. 8.8 - A mass of 8 kg of helium undergoes a process from...Ch. 8.8 - Which is a more valuable resource for work...Ch. 8.8 - Which has the capability to produce the most work...Ch. 8.8 - The radiator of a steam heating system has a...Ch. 8.8 - A well-insulated rigid tank contains 6 lbm of a...Ch. 8.8 - A pistoncylinder device contains 8 kg of...Ch. 8.8 - Prob. 35PCh. 8.8 - Prob. 36PCh. 8.8 - Prob. 37PCh. 8.8 - A pistoncylinder device initially contains 2 L of...Ch. 8.8 - A 0.8-m3 insulated rigid tank contains 1.54 kg of...Ch. 8.8 - An insulated pistoncylinder device initially...Ch. 8.8 - Prob. 41PCh. 8.8 - An insulated rigid tank is divided into two equal...Ch. 8.8 - A 50-kg iron block and a 20-kg copper block, both...Ch. 8.8 - Prob. 45PCh. 8.8 - Prob. 46PCh. 8.8 - Prob. 47PCh. 8.8 - A pistoncylinder device initially contains 1.4 kg...Ch. 8.8 - Prob. 49PCh. 8.8 - Prob. 50PCh. 8.8 - Prob. 51PCh. 8.8 - Air enters a nozzle steadily at 200 kPa and 65C...Ch. 8.8 - Prob. 54PCh. 8.8 - Prob. 55PCh. 8.8 - Argon gas enters an adiabatic compressor at 120...Ch. 8.8 - Prob. 57PCh. 8.8 - Prob. 58PCh. 8.8 - The adiabatic compressor of a refrigeration system...Ch. 8.8 - Refrigerant-134a at 140 kPa and 10C is compressed...Ch. 8.8 - Air enters a compressor at ambient conditions of...Ch. 8.8 - Combustion gases enter a gas turbine at 900C, 800...Ch. 8.8 - Steam enters a turbine at 9 MPa, 600C, and 60 m/s...Ch. 8.8 - Refrigerant-134a is condensed in a refrigeration...Ch. 8.8 - Prob. 66PCh. 8.8 - Refrigerant-22 absorbs heat from a cooled space at...Ch. 8.8 - Prob. 68PCh. 8.8 - Prob. 69PCh. 8.8 - Air enters a compressor at ambient conditions of...Ch. 8.8 - Hot combustion gases enter the nozzle of a...Ch. 8.8 - Prob. 72PCh. 8.8 - A 0.6-m3 rigid tank is filled with saturated...Ch. 8.8 - Prob. 74PCh. 8.8 - Prob. 75PCh. 8.8 - An insulated vertical pistoncylinder device...Ch. 8.8 - Liquid water at 200 kPa and 15C is heated in a...Ch. 8.8 - Prob. 78PCh. 8.8 - Prob. 79PCh. 8.8 - A well-insulated shell-and-tube heat exchanger is...Ch. 8.8 - Steam is to be condensed on the shell side of a...Ch. 8.8 - Prob. 82PCh. 8.8 - Prob. 83PCh. 8.8 - Prob. 84PCh. 8.8 - Prob. 85RPCh. 8.8 - Prob. 86RPCh. 8.8 - An aluminum pan has a flat bottom whose diameter...Ch. 8.8 - Prob. 88RPCh. 8.8 - Prob. 89RPCh. 8.8 - A well-insulated, thin-walled, counterflow heat...Ch. 8.8 - Prob. 92RPCh. 8.8 - Prob. 93RPCh. 8.8 - Prob. 94RPCh. 8.8 - Prob. 95RPCh. 8.8 - Nitrogen gas enters a diffuser at 100 kPa and 110C...Ch. 8.8 - Prob. 97RPCh. 8.8 - Steam enters an adiabatic nozzle at 3.5 MPa and...Ch. 8.8 - Prob. 99RPCh. 8.8 - A pistoncylinder device initially contains 8 ft3...Ch. 8.8 - An adiabatic turbine operates with air entering at...Ch. 8.8 - Steam at 7 MPa and 400C enters a two-stage...Ch. 8.8 - Prob. 103RPCh. 8.8 - Steam enters a two-stage adiabatic turbine at 8...Ch. 8.8 - Prob. 105RPCh. 8.8 - Prob. 106RPCh. 8.8 - Prob. 107RPCh. 8.8 - Prob. 108RPCh. 8.8 - Prob. 109RPCh. 8.8 - Prob. 111RPCh. 8.8 - A passive solar house that was losing heat to the...Ch. 8.8 - Prob. 113RPCh. 8.8 - A 4-L pressure cooker has an operating pressure of...Ch. 8.8 - Repeat Prob. 8114 if heat were supplied to the...Ch. 8.8 - Prob. 116RPCh. 8.8 - A rigid 50-L nitrogen cylinder is equipped with a...Ch. 8.8 - Prob. 118RPCh. 8.8 - Prob. 119RPCh. 8.8 - Prob. 120RPCh. 8.8 - Reconsider Prob. 8-120. The air stored in the tank...Ch. 8.8 - Prob. 122RPCh. 8.8 - Prob. 123RPCh. 8.8 - Prob. 124RPCh. 8.8 - Prob. 125RPCh. 8.8 - Prob. 126RPCh. 8.8 - Prob. 127RPCh. 8.8 - Water enters a pump at 100 kPa and 30C at a rate...Ch. 8.8 - Prob. 129RPCh. 8.8 - Prob. 130RPCh. 8.8 - Obtain a relation for the second-law efficiency of...Ch. 8.8 - Writing the first- and second-law relations and...Ch. 8.8 - Prob. 133RPCh. 8.8 - Keeping the limitations imposed by the second law...Ch. 8.8 - Prob. 135FEPCh. 8.8 - Prob. 136FEPCh. 8.8 - Prob. 137FEPCh. 8.8 - Prob. 138FEPCh. 8.8 - A furnace can supply heat steadily at 1300 K at a...Ch. 8.8 - A heat engine receives heat from a source at 1500...Ch. 8.8 - Air is throttled from 50C and 800 kPa to a...Ch. 8.8 - Prob. 142FEPCh. 8.8 - A 12-kg solid whose specific heat is 2.8 kJ/kgC is...
Knowledge Booster
Background pattern image
Mechanical Engineering
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.
Similar questions
SEE MORE QUESTIONS
Recommended textbooks for you
Text book image
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Text book image
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Text book image
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Text book image
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Text book image
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Text book image
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
First Law of Thermodynamics, Basic Introduction - Internal Energy, Heat and Work - Chemistry; Author: The Organic Chemistry Tutor;https://www.youtube.com/watch?v=NyOYW07-L5g;License: Standard youtube license