College Physics
1st Edition
ISBN: 9781938168000
Author: Paul Peter Urone, Roger Hinrichs
Publisher: OpenStax College
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 9, Problem 2PE
When tightening a bolt, you push perpendicularly on a wrench with a force of 165 N at a distance of 0.140 m from the center of the bolt. (a) How much torque are you exerting in newton × meters (relative to the center of the bolt)? (b) Convert this torque to foot pounds.
Expert Solution & Answer
Trending nowThis is a popular solution!
Chapter 9 Solutions
College Physics
Ch. 9 - What can you say about the velocity of a moving...Ch. 9 - Under what conditions can a rotating body be in...Ch. 9 - What three factors affect the torque created by a...Ch. 9 - A wrecking ball is being used to knock down a...Ch. 9 - Mechanics put a length of Pipe over the handle of...Ch. 9 - A round pencil lying on its side as in Figure 9.13...Ch. 9 - Explain the need for tall towers on a suspension...Ch. 9 - When visiting some countries, you may see a person...Ch. 9 - Scissors are like a double-lever "Stem, Which of...Ch. 9 - Suppose you pull a nail at a constant rate using a...
Ch. 9 - Why are the forces exerted on the outside world by...Ch. 9 - Explain why the forces in our joints are several...Ch. 9 - Why are the forces exerted on the outside world by...Ch. 9 - Explain why the forces in our joints are several...Ch. 9 - Certain of dinosaurs were bipedal (walked on two...Ch. 9 - Swimmers and athletes during competition need to...Ch. 9 - If the maximum force the biceps muscle can exert...Ch. 9 - Suppose the biceps muscle was attached through...Ch. 9 - Explain one of the reasons why pregnant women...Ch. 9 - (a) When opening a door, you push on it...Ch. 9 - When tightening a bolt, you push perpendicularly...Ch. 9 - Two children push on opposite sides of a door...Ch. 9 - Use the second condition for equilibrium (net =0 )...Ch. 9 - Repeat the seesaw problem in Example 9.1 with the...Ch. 9 - Suppose a horse leans against a wall as in Figure...Ch. 9 - Two children of mass 20.0 kg and 30.0 kg sit...Ch. 9 - (a) Calculate the magnitude and direction of the...Ch. 9 - A person carries a plank of wood 2.00 m long with...Ch. 9 - A 17.0-m-high and 11.0-m-long wall under...Ch. 9 - (a) What force must be exerted by the wind to...Ch. 9 - Suppose the weight of the drawbridge in Figure...Ch. 9 - Suppose a 900-kg car is on the bridge in Figure...Ch. 9 - A sandwich board advertising sign is constructed...Ch. 9 - (a) What minimum coefficient of friction is needed...Ch. 9 - A gymnast is attempting to perform splits. From...Ch. 9 - To get up on the roof, a person (mass 70.0 kg)...Ch. 9 - In Figure 9.21, the cg of the pole held by the...Ch. 9 - What is the mechanical advantage of a nail puller...Ch. 9 - Suppose you needed to raise a 250-kg mower a...Ch. 9 - a) What is the mechanical advantage of a...Ch. 9 - A typical car has an axle with 1.10 cm radius...Ch. 9 - What force does the nail puller in Exercise 9.19...Ch. 9 - If you used an ideal pulley of the type shown in...Ch. 9 - Repeat Exercise 9.24 for the pulley shown in...Ch. 9 - Verity that the force in the elbow joint in...Ch. 9 - Two muscles in the back of the leg pull on the...Ch. 9 - The upper leg muscle (quadriceps) exerts a force...Ch. 9 - A device for exercising the upper leg muscle is...Ch. 9 - A person working at a drafting board may hold her...Ch. 9 - We analyzed the biceps muscle example with the...Ch. 9 - Even when the head is held erect, as in Figure...Ch. 9 - A 75-kg man stands on his toes by exerting an...Ch. 9 - A father lifts his child as shown in Figure 9.43....Ch. 9 - Unlike most of the other muscles in our bodies,...Ch. 9 - Integrated Concepts Suppose we replace the 4.0-kg...Ch. 9 - (a) What force should the woman in Figure 9.45...Ch. 9 - You have just planted a sturdy 2-m-tall palm tree...Ch. 9 - Unreasonable Results Suppose two children are...Ch. 9 - Construct Your Own Problem Consider a method for...
Additional Science Textbook Solutions
Find more solutions based on key concepts
1. If an object is not moving, does that mean that there are no forces acting on it? Explain.
College Physics: A Strategic Approach (4th Edition)
The force, when you push against a wall with your fingers, they bend.
Conceptual Physics (12th Edition)
29.29 The conducting rod ab shown in Fig. E29.29 makes contact with metal rails ca and db. The apparatus is in ...
University Physics with Modern Physics (14th Edition)
1. If an object is not moving, does that mean that there are no forces acting on it? Explain.
College Physics: A Strategic Approach (3rd Edition)
The electromagnetic spectrum of light is often arranged in terms of frequency. Which one of the following has t...
Lecture- Tutorials for Introductory Astronomy
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.Similar questions
Can a set of forces have a net force that is zero and a net torque that is not zero?
arrow_forward
A man stands on a merry-go-round that is rotating at 2.5 rad/s. If the coefficient of static friction between the man’s shoes and the merry-go-round is s=0.5 , how far from the axis of rotation can he stand without sliding?
arrow_forward
An automobile engine can produce 200Nm of torque. Calculate the angular acceleration produced if 95.0 of this torque is applied to the drive shaft, axle, and rear wheels of a car, given the following information. The car is suspended so that the wheels can turn freely. Each wheel acts like a 15.0-kg disk that has a 0.180-m radius. The walls of each tire act like a 2.00-kg annular ring that has inside radius of 0.180 m and outside radius of 0.320 m. The tread of each tire acts like a 10.0-kg hoop of radius 0.330 m. The 14.0-kg axle acts like a rod that has a 2.00-cm radius. The 30.0-kg drive shaft acts like a rod that has a 3.20-cm radius.
arrow_forward
Can a single force produce a zero torque?
arrow_forward
What force must be applied to end of a rod along the x-axis of length 2.0 m in order to produce a torque on the rod about the origin of 8.0k Nm ?
arrow_forward
A constant torque is applied to a rigid body whose moment of inertia is 4.0kgm2 around the axis of rotation. If the wheel starts from rest and attains an angular velocity of 20.0 rad/s in 10.0 s, what is the applied torque?
arrow_forward
Answer yes or no to the following questions. (a) Is it possible to calculate the torque acting on a rigid object without specifying an axis of rotation? (b) Is the torque independent of the location of the axis of rotation?
arrow_forward
The cylindrical head bolts on a car are to be tightened with a torque of 62.0Nm . If a mechanic uses a wrench of length 20 cm, what perpendicular force must he exert on the end of the wrench to tighten a bolt correctly?
arrow_forward
Assume a single 300-N force is exerted on a bicycle frame as shown in Figure OQ10.5. Consider the torque produced by this force about axes perpendicular to the plane of the paper and through each of the points A through E, where E is the center of mass of the frame. Rank the torques A, B, C, D, and E from largest to smallest, noting that zero is greater than a negative quantity. If two torques are equal, note their equality in your ranking. Figure OQ10.5
arrow_forward
A simple pendulum consists of a massless tether 50 cm in length connected to a pivot and a small mass of 1.0 kg attached at the other end. What is the torque about the pivot when the pendulum makes an angle of 40 with respect to the vertical?
arrow_forward
Calculate the rotational kinetic energy of a 12-kg motorcycle wheel if its angular velocity is 120 rad/s and its inner radius is 0.280 m and outer radius 0.330 m.
arrow_forward
What three factors affect the torque created by a force relative to a specific pivot point?
arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
University Physics Volume 1
Physics
ISBN:9781938168277
Author:William Moebs, Samuel J. Ling, Jeff Sanny
Publisher:OpenStax - Rice University
Principles of Physics: A Calculus-Based Text
Physics
ISBN:9781133104261
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Physics for Scientists and Engineers: Foundations...
Physics
ISBN:9781133939146
Author:Katz, Debora M.
Publisher:Cengage Learning
Glencoe Physics: Principles and Problems, Student...
Physics
ISBN:9780078807213
Author:Paul W. Zitzewitz
Publisher:Glencoe/McGraw-Hill
College Physics
Physics
ISBN:9781938168000
Author:Paul Peter Urone, Roger Hinrichs
Publisher:OpenStax College
University Physics Volume 1
Physics
ISBN:9781938168277
Author:William Moebs, Samuel J. Ling, Jeff Sanny
Publisher:OpenStax - Rice University
Principles of Physics: A Calculus-Based Text
Physics
ISBN:9781133104261
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Physics for Scientists and Engineers: Foundations...
Physics
ISBN:9781133939146
Author:Katz, Debora M.
Publisher:Cengage Learning
Glencoe Physics: Principles and Problems, Student...
Physics
ISBN:9780078807213
Author:Paul W. Zitzewitz
Publisher:Glencoe/McGraw-Hill
College Physics
Physics
ISBN:9781938168000
Author:Paul Peter Urone, Roger Hinrichs
Publisher:OpenStax College
What is Torque? | Physics | Extraclass.com; Author: Extraclass Official;https://www.youtube.com/watch?v=zXxrAJld9mo;License: Standard YouTube License, CC-BY