Describe tapper noise

Q: Describe How to mesh irregular volume by using ANSYS?

A: To mesh a volume with all hexahedron elements, the following conditions must be satisfied; 1.The…

Q: Under staticload or when static load is applied ,most of the machine elements re failed  True…

A: Under staticload or when static load is applied ,most of the machine elements re failed  True  False…

Q: chir

A:

Q: Statics; working

A:

Q: Match the following. Screwing is an example of Lapping is an example of

A: Solution:

Q: vill become tu

A:

Q: what is the impact of mechanical vibration on following a. Bearing House of Lathe machine b.…

A: Answer         c. Fatigue life of materials

Q: What is damped Vibration.

A: Given Data : damped Vibration.

Q: Explain briefly the sorts of interruptions and why they are crucial to the machine.

A:

Q: The hydraulic cylinders is also known as

A: The hydraulic cylinder is a mechanical actuator which convert hydraulic energy  into the mechanical…

Q: In transition fit, tolerance zone of hole is entirely above that of shaft tolerance zones of hole…

A:

Q: in the an:iclo-kwise di

A:

Q: onsidered as d

A: given: Describe the nature of force vibrations why their considered as destructive.

Q: Explain in detail about the two types of shaft alignment, soft foot, and indicator sag.

A:

Q: What is the difference between a bellows and a diaphragm?

A: The Bellows and diaphragm  are pressure measuring  devices.   The difference between then are given…

Q: Demonstrate reed type comparator with the help of examples and figure.

A: Reed type comparator,

Q: rance between an alloy that failed at a lo

A: (e) In materials science, weariness is the debilitating of a material brought about by cyclic…

Q: the speed can be positive or negative false true

A: Speed is a scalar quantity. it has no direction so, speed can be positive or zero. it cannot be…

Q: a. Explain resonant earthing system with diagram b. How will you give Combined Leakage and Overload…

A: (a) Resonant earthing system : Resonant earthing is a sure uncommon sort of high impedance earthing…

Q: ystem.

A: given: Explain overdamped, critically damped and underdamped system.

Q: Describe two scales in Vernier Caliper?

A: Vernier caliper instrument is mainly used for taking accurate linear measurements. Vernier caliper…

Q: Worn teeth on a speed gear can cause?

A: worn teeth creates a big problem in gear drive.

Q: Write a short note any five sections of separator? in oil And gas

A:

Q: Sketch and explain the working principle, parts, types and application of a Dial Test Indicator

A: given; Sketch and explain the working principle, parts, types and application of a Dial Test…

Q: Describe the action of a commutator.

A: Introduction to commutator: commutator is a mechanical part of DC generator or motor which converts…

Q: Pressure Transducer Basic principle of operation Application Diaphragm Capsule C-Shaped Bourdon Tube

A: Pressure transducer  converts the physical change caused by applied pressure into a voltage signal…

Q: Explain it properly with full defination and formula used

A: To find:-  Head loss formula explaination

Q: What is damping Vibration.

A: Given Data : damped Vibration.

Q: Problems in TBM (tunnel boring machine) cutting disc production and design errors in the cutting…

A: A well designed cutter disc used in TBMs to excavate very hard and abrasive rock efficiently. The…

Q: A metal disc of 20 mm diameter is to be punched from a sheet of 2 mm thickness. The punch and the…

A: As per given  Metal disc diameter =20mm Clearance =3% We have to find determine of punch

Q: ism to push a box, as shown below

A: Motor specification'   Torque  - τ = 85Nm r= 25m   (b) we know that  τ = F*r = Fr sin θ  = Fr F = τ…

Q: Define; (a) Cut-in speed, (b) Cut-out speed, and (c) Betz limit

A: (a) Cut-in speed It is defined as a minimum speed at which the turbine starts generating…

Q: Please choose the correct answer about scrubber systems on ships.

A: Scrubber systems can be implemented existing ship as per new ship regulation, so option A is wrong .…

Q: :Measurement of vibration is required to

A: GIVEN DATA A MCQ GIVEN ASKING VIBRATION MEASUREMENT REQUIRED TO WE HAVE TO CHOOSE CORRECT OPTION

Q: Define the difference between an integrated and a nonintegrated antilock breaking system

A:

Q: What is the difference between floating and slidingcalipers

A: In the braking system, both floating and sliding calipers are used as per the requirement of the…

Q: Describe briefly the operation of mechanical speed measuring and non-mechanical speed measuring…

A:

Q: Give an outline description of the operation of a GMR Read head.

A: A GMR magnetic media reading head. As the magnetic recording medium passes beneath the GMR sensor,…

Q: 11. Fluid sealing in a dashpot is achieved using

A: GIVEN DATA A MCQ GIVEN ASKING WHICH SEALING USED IN FLUID DASHPOT SYSTEM

Q: Explain Miner's Rule and discuss the limitation in applying Miner's Rule.

A: The power capacity of a Gear Drive is a critical aspect in ensuring that driven equipment runs…

Q: The wrenches are used for clearing burrs from work surfaces. Select one: True False

A: The wrenches are used for clearing burrs from work surfaces. Select one: True False

Q: 2.... Hydraulic controlled riveting assembly machine. hydraulic control system. Must include the…

A:

Q: Describe the types of Pressure and how to mesure.

A: Pressure  - Pressure is defined as the force applied perpendicular to an object per unit area.…

Q: Q2) ______________________ and ______________________ are two common filing problems that can be…

A: File tools are used mainly for finishing of the material by removing the metals from the surface and…

Limits, Fits, and Tolerances

The maximum or minimum allowable sizes within which the size of component lies are known as limits. The limits are classified into two types: