11th Edition

ISBN: 9780134893501

Author: Richard R. Kibbe, Roland O. Meyer, Jon Stenerson, Kelly Curran

Publisher: PEARSON

Concept explainers

Screw threads are a series of ridges having the profile of a helix. This helix profile runs continuously along the length of a uniform solid or a hollow bar of a circular cross-section at periodic intervals. These helix ridges are also formed over a coni…

Videos

Textbook Question

Chapter B.6, Problem 1ST

What type of tap is used to produce threads that extend almost to the bottom of a blind hole.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter B.5, Problem 10ST

Chapter B.6, Problem 2ST

Students have asked these similar questions

What form of screw thread is most commonly used in japan?

What does the identifier for a unified thread indicate as a minimum?

What size of hole should be bored before cutting a 7/8 in. internal thread having 9 TPI and 12 mm. internal thread having 1.75 no. of pitch?

Chapter B Solutions

Machine Tool Practices (11th Edition)

Ch. B.1 - List several uses of the arbor press.Ch. B.1 - A newly machined steel shaft with an interference...Ch. B.1 - The ram of an arbor press is loose in its guide...Ch. B.1 - When a bushing is pushed into a bore that is...Ch. B.1 - Prob. 5ST Ch. B.1 - What difference is there in the way a press fit is...Ch. B.1 - Prior to installing a bushing with the arbor...Ch. B.1 - Name five ways to avoid tool breakage and other...Ch. B.2 - Name two types of bench vises Ch. B.2 - Prob. 2ST

Ch. B.2 - How can the finished surface of a part be...Ch. B.2 - Name three things that should never be done to a...Ch. B.2 - How should a vise be Lubricated?Ch. B.2 - Prob. 6ST Ch. B.2 - What advantage does the lever-jawed wrench offer...Ch. B.2 - Some objects should never be struck with a hard...Ch. B.2 - Why should pipe wrenches never be used on bolts,...Ch. B.2 - What are the two important things to remember...Ch. B.3 - What is the kerf?Ch. B.3 - What is the set on a saw blade?Ch. B.3 - What is the pitch of the hacksaw blade?Ch. B.3 - What determines the selection of a saw blade for a...Ch. B.3 - Hand hacksaw blades fall into two basic...Ch. B.3 - Give four causes that make saw blades dull.Ch. B.3 - Give two reasons why hacksaw blades break.Ch. B.3 - A new hacksaw blade should not be used in a cut...Ch. B.4 - What are the four different cuts found on files?Ch. B.4 - Name four coarseness designations for files.Ch. B.4 - Which of the two kinds of files-single cut or...Ch. B.4 - What are the coarseness designations for needle...Ch. B.4 - Prob. 5ST Ch. B.4 - What causes a file to get dull?Ch. B.4 - Why should a handle be used on a file?Ch. B.4 - How does the hardness of a workpiece affect the...Ch. B.4 - Should pressure be applied to a file on the return...Ch. B.4 - Why is a round file rotated while it is being...Ch. B.5 - Prob. 1ST Ch. B.5 - What is the purpose of a starting taper on a...Ch. B.5 - What is the advantage of a spiral flute reamer...Ch. B.5 - How does the shank diameter of a hand reamer...Ch. B.5 - Prob. 5ST Ch. B.5 - Prob. 6ST Ch. B.5 - What is the purpose of cutting fluid in reaming?Ch. B.5 - Prob. 8ST Ch. B.5 - How much reaming allowance is left for hand...Ch. B.5 - If you were repairing the lathe tailstock taper,...Ch. B.6 - What type of tap is used to produce threads that...Ch. B.6 - Prob. 2ST Ch. B.6 - Prob. 3ST Ch. B.6 - When is a spiral fluted tap used?Ch. B.6 - How are thread-forming taps different from...Ch. B.6 - How are taper pipe taps identified?Ch. B.6 - Why are finishing and roughing Acme taps used?Ch. B.6 - Why are rake angles varied on taps for different...Ch. B.7 - What kind of tools are used to drive taps when...Ch. B.7 - What is a hand tapper?Ch. B.7 - What is a tapping attachment?Ch. B.7 - Which three factors affect the strength of a...Ch. B.7 - How deep should the usable threads be in a tapped...Ch. B.7 - What causes taps to break while tapping?Ch. B.7 - What causes rough and tom threads?Ch. B.7 - Give three methods of removing broken taps from...Ch. B.8 - What is a die?Ch. B.8 - What tool is used to drive a die?Ch. B.8 - How much adjustment is possible with a round split...Ch. B.8 - What are important points to watch when assembling...Ch. B.8 - Why do dies have a chamfer on the cutting end?Ch. B.8 - Why are cutting fluids used?Ch. B.8 - What diameter should a rod be before being...Ch. B.8 - Why should a rod be chamfered before being...Ch. B.9 - Prob. 1ST Ch. B.9 - Why should a tool grinder never be used for rough...Ch. B.9 - Prob. 3ST Ch. B.9 - Prob. 4ST Ch. B.9 - Prob. 5ST Ch. B.9 - Prob. 6ST Ch. B.9 - Prob. 7ST Ch. B.9 - What is the purpose of the wheel blotter?Ch. B.9 - Prob. 9ST Ch. B.9 - What does the wheel ring test do?

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

What type of tap is used to produce threads that extend almost to the bottom of a blind hole.

Solution Summary: The author explains the use of bottoming taps for threading blind holes. Only 1.5 threads of tap are removed when it rotates by hand.

Concept explainers

Videos

Want to see the full answer?

Chapter B Solutions