Printed circuit board

Page 1 of 37 - About 365 essays
  • 20.1 PCB BOARD A printed circuit board, or PCB, is worn to mechanically support and electrically

    1100 Words  | 5 Pages

    PCB BOARD A printed circuit board, or PCB, is worn to mechanically support and electrically connect electronic components by means of conductive pathways, tracks or signal traces etched from copper sheets laminated onto a non-conductive substrate. It is also referred to as printed wiring board (PWB) or etched wiring board. Printed circuit boards are used in virtually all but the simplest commercially produced electronic devices. A PCB populated with electronic components is called a printed circuit

  • Strength And Utilization Of Wastes Printed Circuit Boards

    703 Words  | 3 Pages

    Wastes printed circuit boards(pcbs) are approximately 30% metals and 70% nonmetals. It contains large amount of silica in its refined form. Hence it forms the ideal replacement material of fine aggregate in concrete, it can be result in reducing the dead weight of the structure. The pcbs are inactive in nature which makes it as an compulsory component in all the electronic devices. And it gives desire to its inert nature, it can not participate in any further reaction with the concrete matrix and

  • School Of Business And Computer Science

    1138 Words  | 5 Pages

    TECHNOLOGY Course : Advanced Computer Aided Systems (Electrical) Lecturer : Daniel Ringis WS3 : PCB Manufacture Submitted by : Valmiki Singh (26908)   Task 1 a. Dry Film Resist Coating material to mask a copper pattern that is designed for a printed circuit board to accommodate the etching and solder. b. Clean room A room in which the concentration of air born particles is controlled to lessen the effect dust has on imaging. c. Photoplot The product of scanning imaging data onto films. Referred to

  • Case Study Of The Leopold KOSTAL Group

    1646 Words  | 7 Pages

    The Leopold KOSTAL GmbH is an independent, globally orientated family-run company, which was founded in 1912 in Ludenscheid. Around 1927, they developed and produced products for automobiles for the first time. In 1973, Helmut Kostal decided to start the first overseas KOSTAL plant in Mexico to allow the company to grow internationally. In 2017, an annual turnover of € 2,470 million is planned. This would be a plus of € 106 million compared to the previous year of 2016. The aim of the KOSTAL Group

  • Microstrip Antennas : An Analysis

    946 Words  | 4 Pages

    patch edge and the ground plane cause the microstrip patch antennas to radiate. An individual microstrip antenna consists of a patch of metal of various shapes on the surface of a PCB, with a metal ground plane on the other side of the board. Most microstrip antennas consist of multiple patches in a

  • Essay about Science Technology Company

    653 Words  | 3 Pages

    testers for printed circuit boards • Second largest in semiconductor test operation • Objective: To be the recognized international leader in providing integrated quality management systems to manufacturers of electronic devices and equipment. • Strategies: o Heavy

  • Electronic Voting Machine

    4319 Words  | 18 Pages

    International Journal of Information and Electronics Engineering, Vol. 3, No. 2, March 2013 A Preview on Microcontroller Based Electronic Voting Machine Diponkar Paul and Sobuj Kumar Ray, Member, IACSIT Abstract—Voting is most pivotal process of democratic society through which people determine it’s government. Governments around the world are increasingly considering the replacement of traditional paper-based voting schemes with electronic voting systems. Elections of Bangladesh are conducted

  • North American Electro-Deposited Copper Foil

    3942 Words  | 16 Pages

    North American Electro-Deposited Copper Foil Jonathan Blaber Prof. Warren 09 December 2010 Table of Contents: 1) Introduction 3 2) Supply 4 3) Demand 6 4) Equilibrium 8 5) Neighboring Markets 9 6) Competition 10 7) Imperfections

  • Fabrication Of Pcb And Pcb

    1733 Words  | 7 Pages

    FABRICATION OF PCB The Printed Circuit Board (PCB) provides the electrical interconnections between various components and as well provides mechanical support to the components. The components are soldered to the PCB. The quality of the soldering directly affects the reliability of the circuit. The procedure for fabricating the PCB for any general project is described below. 7.1 PCB MAKING Making of PCBs is as much as an art as a technique. The making of PCB essentially involves two steps. •

  • The Digital Revolution : The Generation Of Electronic Waste, Or E Waste

    1919 Words  | 8 Pages

    The digital revolution has resulted in many technological advances that positively contribute to our society and the environment. Examples include advanced data collection and surveillance techniques, improved responses to environmental and social crises, increased communication, and a seemingly unlimited access to information. However all the benefits from this movement also usher in many negative effects. Due to rapid technological innovation, we often find ourselves consistently “upgrading” our

Previous
Page12345678937