Sugar solution

Red solution; brown precipitate when heated. | SO32- ; CH3COO- may present | | Purplish solution decolourise. | S2O32- may present | (iv) Add aqueous silver nitrate, followed by HNO3 | White precipitate, soluble in HNO3 / NH3 (aq), or SO32− in excess; turn black precipitate when heated. | SO32- may present | | White precipitate turn to yellow and then brown and finally black; white precipitate soluble in excess S2O32−. | S2O32- may present | | White precipitate in concentrated solution, soluble

"Do different concentrations of solutions determine the mass of a potato?" Introduction: The way to get the full results of this lab was through the process of osmosis. Osmosis is the movement of water across a membrane into a more concentrated solution to reach an equilibrium. When regarding cells osmosis has three different terms that are used to describe their concentration. The first of these words is isotonic. Cells in an isotonic solution show that the water has no net movement and the amount

lecture, you will be able to Define viscosity and viscosity coefficient Outline the method to measure viscosity using Ostwald viscometer Determine the average molecular weight of a polymer Determine the surface concentration of 1-butanol in aqueous solution Measure the distribution coefficient of a solute betweenn two solvents 39.1 Introduction Viscosity, one of the transport properties, arises because of intermolecular attractive and relatively long-range forces. Viscosity coefficient ([pic])

Effects of temperature manipulation and solution treatment on the Beta vulgaris craca plant cell membrane and the change of the concentration of betacyanin when placed under these various stresses Introduction: The Beta vulgaris craca plant, commonly referred to as the beet root contains a pigment, red in colour, called betacyanin. The betacyanin’s containment within the cells of the beet root cell relies on the stability of the plant’s membrane structure. The manipulation of the cell’s membranes

is used to purify solids. This process dissolves a crude solid with impurities in a mildly boiling solvent, and cooling down the mixture afterwards for crystals to reconstruct themselves in solution. This method allows impurities to separate and remain in solution as precipitate or remain uniform in solution. Solids are more soluble in hot solvents than in cold ones, allowing maximum dissolution for proper separation and subsequent crystallization to occur. After purifying the compound, the melting

is considered hypertonic. When a red blood cell is dropped into a beaker of distilled water solution the red blood cell will burst. The reason the red blood cell exploded was because the cytosol has more solute than the distilled water and the distilled water move into red blood cell. This environment is called hypotonic. If a red blood cell is dropped into a beaker of the same solute concentration solution as the cytosol, the water will move in and out of the cell. This creates no net movement of

potato strips and three unknown solutions (A, B, C). First three slides were prepared containing RBC’s and unknown solutions A, B and C. A control slide was prepared only using RBC’s. After observing each slide under the microscope it was determined that unknown solution A was hypertonic because the RBC appeared to have shrunk. The RBC in unknown solution B appeared to be swollen, therefor, the tonicity of unknown solution B was hypotonic. Unknown solution C showed no change to the RBC shape

the substrates and active sites of enzyme increase due to the increasing amount of active sites which allow more collisions to happen, so the rate of breakdown of lipids to simpler substances will increase. During the experiment, sodium carbonate solution and pH indicator phenolphthalein will be added ahead of

inside of the cell creating a hypotonic solution. The increase in water inside the cell causes the cell to become engorged and erupt. In a

criteria for evaluating solutions. The solution can be either a practical one, which would affect material gains or losses, or one based on value, which would fallow a goal that reflects image or purpose. Max and George have decided to incorporate both types, and each solution that they come up with must meet the established criteria. The solution must cause a 5% increase in sales, must be cost effective, and can not affect the quality of the products. 3. Identify possible solutions This is where the parties