Q1: Answer the following statements with (True) or (False),1) Pgz is the dynamic pressure it represents the pressure rise when thefluid in motion is brought to a stop isentropically.2) If they are of particular section increase, then the velocity decrease ispossible then that section.3) The objective of flow measurement by venture meter is measuring thetheoretically discharge.4) When the coefficient of contraction of negative relationship withcoefficient of discharge.5) The objectives flow measuring by orifice meter is determining thecontraction of coefficients only.6) The losses in the plastic material are less than the losses in the ironmaterial.

1. Answer:- False Explaination:- pgz is not the dynamic pressure and it is the hydrostatic…

1) Pgz is the dynamic pressure it represents the pressure rise when the fluid in motion is brought to a stop isentropically. 2) If they are of particular section increase, then the velocity decrease is possible then that section.

1) Pgz is the dynamic pressure it represents the pressure rise when the fluid in motion is brought to a stop isentropically. 2) If they are of particular section increase, then the velocity decrease is possible then that section.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A differential "U"-tube manometer containing mercury of density 13000 kg/m³ is used to measure the pressure drop along a horizontal pipe. If the fluid in the pipe is water and the manometer reading is 0.65m, what is the pressure difference between the two tapping points? Fluid density Pw A B a b datum Manometric fluid density p Hg Figure of manometer setup
Qsn. Plot the flow curve of liquid limit according to the data given in the table.
A steady push on the piston in a syringe is shown in the figure causes a flow rate of 0.4 ml/sec. The fluid has a mass density of 900 kg/cum and an absolute viscosity of 0.002 Pa-sec. Assume that there is no headloss in the larger cylinder. Determine the reynolds number for the given flow of 0.4 ml/sec in he needle. 645 917 897 795 Determine the headloss in the needle 18.90 m 15.21 m 14.43 m 16.23 m Determine the force required to maintain the flow 64.23 kn 45.25 kn 34.77 kn 25.36 kn
16. Fluid Flow through a Compression Chamber A compressible gas flows into and out of a compression chamber as shown in Figure 9. Vin = 10 m/s Ain = 0.1 m² Pin = 3.0 kg m-3 (a) Bsys = 0 (b) bsys = dB sys dt Control Surface For the system given, which of the following statement(s) are true based on the conti- nuity equation? Be certain to justify your answer quantitatively. 0 Control Volume Figure 9: Schematic of compression chamber. (c) #0 (d) Σsbpv · A = 0 (e) & Spdv = 0 Vout = 5 m/s Aout = 0.2 m² Pout = 2.0 kg m-3 Answer(s): # 0; dB sys dt
Question 1 b) The U-tube manometer can be used to detemine pressure difference between two systems. This type of manometer is called a differential U-tube manometer. Consider the differential manometer connected to a pipe, as shown in Figure 1. Explain step by step on how you can calculate the pressure difference between point A and B. P1 h, A Flow Test Section U-Tube Differential Manometer
Question 2. The manometer in the figure is used to measure the pressure difference between two points in the pipe. The density of the water in the pipe is 1000 kg/m3 and the valve is open. If the readings on the manometer are z1= 100 mm, z2= 250 mm and h= 90 mm, how many N/m2 is the difference between P1 and P2? watplf Valve aik
A venturimeter is: efully designed pressure difference is a measure of flow volume rate in a pipe. Using Bernoulli's equation for steady, incompressible flow with no loses, show that the flow rate is related to the manometer reading 2gh(p_ - p) h by Q =- where pm is the density of the manometer fluid.
Paint issues from the tank at a flow rate of 45 ft^3/s. Find the kinetic viscosity in ft^2/s. Assume the flow is laminar. Note: In answering the question, it must be in exponential form but in the text box just write the value no need to include the x10^-1.. 9 ft L=6 ft d=in B Q
civil engineering Dont give wrong answer and copy I will report and give dislike If the rate distribution of a viscous liquid (u= 0-eight Ns/m2) over a fixed boundary is given with the aid of u zero-68yy2wherein u is the speed in m/s at a distance y metres above the boundary floor, decide the shear stress on the floor and at y = 0.35m.
Q3: A pitot-static tube is used to measure the flow velocity of turpentine flowing in a pipeline if the manometer reading is 8 cm of mercury, calculate the average velocity, pressure drop, and volumetric flow rate at that point in the pipe line. Also evaluate Reynold number for turpentine and which type of flow in the pipe. Ph J Re Density of turpentine is 850 kg/m³, density of mercury is 13600 kg/m³, cv = 1, D=10 cm, turpentine 0.001375 and 0 = 45°. =
Paint issues from the tank at a flow rate of 45 ft^3/s. Find the kinetic viscosity in ft^2/s. Assume the flow is laminar. Note: In answering the question, it must be in exponential form but in the text box just write the value no need to include the x10^-1.. A 9 ft L = 6 ft d = 1/2 in ܪ e
A uniform 10-kg bar OA is suspended from the pin at O. The bar is at rest when the 1.5 kg bal B with negligible diameter hits end A with a velocity of VB1-30 m/s. After the impact, the ball bounces off following the direction shown. 0 A VB2 1. What is the angular velocity of rod OA just after impact? 2. What is the coefficient of restitution between ball B and rod OA? B VB1 24 1.8 m