1. Determine the maximum range and maximum endurance of a propeller-driven airplane.W₁ = 367 lbc = 0.45 lb/hphW₂ = 2950 lbS = 174 ft²CDO = 0.0239e = 0.85Sea Leveln = 0.8b = 34.04 ft

Answered: Image /qna-images/answer/b4dc3eec-2277-4e5e-9c1e-b8beb0038b9a.jpg

Answered: 1. Determine the maximum range and…

1. Determine the maximum range and maximum endurance of a propeller-driven airpla W₁ = 367 lb c = 0.45 lb/hph W₁ = 2950 lb S = 174 ft² CDO = 0.0239 e = 0.85 Sea Level n = 0.8 b = 34.04 ft

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Mass = 147 kg coefficent of friction= 0.37 h = 4 m
A hydraulic cylinder is used to lift a load of 750 lbf a distance of 4 ft in 3 seconds. Compute the power and fluid horsepower. OP = 1.8 hp and FHP = 1.82 P= 4.7 hp and FHP = 4.7 P= 6.4 hp and FHP = 7.8 O P= 7.2 hp and FHP = 16.4
Q4/ Answer the following question Determine the engine speed if reading of a dynamometer that is connected to a V6 engine is 130kW. The engine is square and its crank offset is 7.2 cm. The pressure inside one cylinder is 1100 kPa. The mechanical efficiency of this engine is 85%.
The two following 2 energy level systems (E; = 0 & E; = 1) are brought into thermal contact: System A: 8 distinguishable particles; UA = 4 System B: 4 distinguishable particles; UB = 1 If a single unit of energy transfers from System A to System B, what is the final Wtot for the combined system?
What is the maximum time (in hours, nearest hundredths) a glider can achieve over the ground if it were to perform unpowered descent from an altitude of 4,011 m? Its weight = 2,663 N, Area = 16.1 m², and CD=0.011 +0.026C₁2. Assume SSLC (1.225 kg/m³) and cosy 1.
Q1: Answer the following: (35 Degree) 1. Discuss each situation below as approximating an a closed, or an open system. (a) Desert Cooler (b) Air in a balloon. 2. A spring have stiffness of 100 N/m, is fixed as shown in Fig. A 2.0 kg block mass is moved up the surface with an initial kinetic energy of 18 J, if the initial distance is 0.5m, 0= 37. Determine the kinetic energy of the box mass, at which the mass block moved up. If the block stop at the case when the spring is compressed about 0.5 m.
Q5: A jet engine airplane has a weight of 64 kN and wing area of 20 m². If the engine output be 8 kN, calculate the maximum and minimum speeds in level flight? Given that CD. = 0.017, AR= 6.5, e=0.80, CLmax T 1.4. (17.5 degree)
An elevator has a rated capacity of 2200 lb. It can transport people at the rated capacity between the first and the fifth floors, with a vertical distance of 15 ft between each floor, in 7 s. Estimate the power requirement for 3 such an elevator. slo2 svizan s
ament/d/1okY5rWmMz5Vd-YFU_hfJWhfGwpRCjlfo7T64xInJcmo/edit clorosis science project 8th... Tobiloba Aderemi -. 9 Clever logo Connect コ 4. You wish to lift a 400 lb car engine a vertical distance of 3 ft using a strong rope. Unfortunately, your hand crank winch can only generate 100 lbs of tension in your rope. In order to overcome this obstacle, you use a multiple pulley system (block and tackle) to lift the engine. a. What is the mechanical advantage of this system? B. what length of rope is required to complete the work 400 tb Foundations of Technology TEEA.neineering by Design"" DesignTM
Drill pipes of 1000 meter original length which is between top drive drilling motor and bottom hole assembly (HWDP, collar and drill bit) is lowered into the well. The specification of drill pipe is as follows: OD=200 mm, ID=175 mm, E = 50 GPa, G=77.2 GPa weight : drill pipe = 100,000 N , bottom hole assembly = 35,000 N Before the bottom hole assembly touch the rock formation: а) Calculate the reaction force between drill pipe and top drive drilling motor b) Calculate the elongation of drill pipe After the bottom hole assembly rest/touch on the rock formation, the elongation of the drill pipe reduces by half. c) Calculate the reaction force between drill pipe and top drive drilling motor. d) Knowing that the top steel drill pipe rotates through two complete revolutions before the drill bit starts to operate, determine the maximum shearing stress caused in the pipe by torsion.
3. Please calculate the annual electricity production of a wind farm with 20 turbines. The annual mean wind speed is 7 m/s and diameter of the blades is 20 m. If we assume power consumption of a person is 3,000 kWh, about how many people will this energy support? Annual electricity production (KWh) = K Vm³ At T Where: - - - K = 3.2 (factor based on turbine performance) Vm= annual mean wind speed (m/s) At = swept area of turbine (m2) T = number of turbines Suitable for medium- to large-scale wind turbines (> 200 m2 swept area)
A block is pulled along a rough level surface at constant speed by the force P. The figure shows the free-body diagram for the block. FN represents the normal force on the block; and / represents the frictional force. If the coefficient of kinetic friction, HR , between the block and the surface is 0.30 and the magnitude of the frictional force is 80.0 N, what is the magnitude of the normal force FN? mg OA 410 N OB 160 N OC 1.6 N OD.4.0 NA OE 270 N