1. The diodes in the circuit are Silicon with a 10K D1 forward voltage of 0.7 V. Fill up the table showing the state, voltage and current of each of the diodes. Show how you 1K 8K validated the state of each diode. Follow 3 V D3A (1): D2 the reference shown in determining whether the diode voltages and currents are positive or negative.

1. The diodes in the circuit are Silicon with a 10K D1 forward voltage of 0.7 V. Fill up the table showing the state, voltage and current of each of the diodes. Show how you 1K 8K validated the state of each diode. Follow 3 V D3A (1): D2 the reference shown in determining whether the diode voltages and currents are positive or negative.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
What is the difference between a diode and rectifier?
What is CEMF?
Complete the table. Make a forward bias and reverse bias graph using SILICON DIODE. Then explain how did you get the values after you complete the table. Explain how you plot the graph for the forward and reverse biased. To sketch the characteristic curve of the diode you need to vary voltages on diode and measure current flowing during forward and reverse bias condition. Fill up the table below using circuit shown and vary battery voltages. Measure voltage and current of diode then sketch the graph. Voltage X axis and Current Y axis. The multisim is the reference for the table.
The diodes in the circuit are Silicon with aforward voltage of 0.7 V. Fill up the tableshowing the state, voltage and current ofeach of the diodes. Show how youvalidated the state of each diode. Followthe reference shown in determiningwhether the diode voltages and currentsare positive or negative.
Calculate the voltage and current of the diode in the figure for each of the diode's models. In each case, determine the voltage across the resistor. Additionally, in each case, determine the diode's power. Assume that Rb is ten ohms.
Calculate the currents passing through the diodes D1 and D4 in the circuit given below. (All diodes are silicon).
Calculate the current flowing through the given circuit and the voltage value at the V0 ends. (Threshold voltage = 0.3V for Germanium diodes, Threshold voltage for silicon diodes = 0.6V)
Determine the state of diode for the circuit shown and find ID, VD. Assume simplified model for the diode. 4k02 2V 1k02. Off, 0.00mA, 0.4V O Off, -0.005mA, 0.0v On, 0.48mA, 0.6v On, 0.55mA, 0.7v Option 5
The following circuit uses two Zener diodes with reverse breakdown voltage of 5.1 V for each. (1-a) Explain the operation of the Zener diode in forward and in reverse bias. (1-b) Analyze the circuit thoroughly assuming many source values that lead to all possible cases of diode states. For each case (Hint: 3 cases), re-plot the circuit and develop the relation between the output voltage and the source. (1-c) Draw input and output waveforms accurately over 0.5-ms period. Identify the diode states on the graph based on the categorization of cases from part (1-b). (1-d) Use Multisim to verify all of your results. Compare andcomment.
What will be the value of the reverse saturation current for a Si diode operating in forward bias mode. The following information is given: Diode current 3 A Voltage across diode 0.25 V. Temperature is 300 K.
Consider the circuit shown in Figure 2. The cut-in voltage of each diode is . Let and assume both diodes are conducting. Determine if this is a valid assumption and explain your answer. And calculate the values of IR, ID, Ip2, and V.. Rj =1.7 kQ ww VB =1 V D1 Dz R2D 4 kQ Figure 2