Q 551. What is the boundary tension called where the material ceases to comply with Hooke'sLaw?2. How can a material with final deformation of 10% be characterized?3. The stress-strain curve with the actual stress is calculated in the current area and hasdifferent final stress from the engineering stress, being called...4. What is the stress that causes permanent deformation in the material?5. What is the % range of the yield limit of some steels referring to the limit stress thatthe material begins to suffer deformation?6.For what type of material can the Octahedral Stress Criterion be applied?7. What is the tension at which the material begins to soften?

Hi! Thank you for the question. As per the honor code. We are allowed to answer 3 Sub-parts at a…

1. What is the boundary tension called where the material ceases to comply with Hooke's Law? 2. How can a material with final deformation of 10% be characterized? 3. The stress-strain curve with the actual stress is calculated in the current area and has different final stress from the engineering stress, being called...

1. What is the boundary tension called where the material ceases to comply with Hooke's Law? 2. How can a material with final deformation of 10% be characterized? 3. The stress-strain curve with the actual stress is calculated in the current area and has different final stress from the engineering stress, being called...

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 6.2P

See similar textbooks

Similar questions

The state of stresses in the x and y directions at a point in a given material is shown in the figure below. If the value of the shear stress in the x-y axes Ty is 17N/mm2, find the maximum shear stress that can be found at this point in any possible direction. Round off your answer to the nearest N/mm2. 10 N/mm2 Txy 20 N/mm2 20 N/mm2 Txy 10 N/mm2
1.17 Figure P1.17 shows the stress-strain relations of metals A and B during tension tests until fracture. Determine the following for the two metals (show all calcu- lations and units): a. Proportional limit b. Yield stress at an offset strain of 0.002 in./in. 150 - - Metal A 100 • Metal B 50 0.00 0.02 0.04 0.06 0.08 0.10 0.12 0.14 Strain, in./in. FIGURE P1.17 c. Ultimate strength d. Modulus of resilience e. Toughness f. Which metal is more ductile? Why? Stress, ksi
Q.3: A steel rod with a cross sectional area of 150 mm² is stretched between two fixed points. The tensile load at 20°C is 5000 N. a) What will be the stress at -20°C. b) At what temperature will the stress be zero? Assume a-11.7 μm/m . °C and E= 200 GPa?
A steel alloy specimen having a rectangular cross section of dimensions 19.1 mm x 3.1 mm (0.7520 in. × 0.1220 in.) has the stress-strain behavior shown in the Animated Figure 6.22b. If this specimen is subjected to a tensile force of 98290 N (22100 Ib;) then (a) Determine the amount of elastic strain induced. (b) Determine the amount of plastic strain induced. (c) If its original length is 610 mm, what will be its final length after this force is applied and then released? The elastic modulus for steel is 207 GPa. (a) i (b) i (c) i mm
A 5-mm-thick rectangular alloy bar is subjected to ajtensile load P by pins at A and B, as shown in the figure. The width of the bar is w = 33 mm. Strain gages bonded to the specimen measure the following strains in the longitudinal (x) and transverse (y) directions: €, =710 με and ε,--255 με (a) Determine Poisson's ratio for this specimen. (b) If the measured strains were produced by an axial load of P = 24 kN, what is the modulus of elasticity for this specimen? Answers: (a) v= (b) E= GPa
1.14 The stress-strain relation shown in Figure P1.14 was obtained during the ten- sile test of an aluminum alloy specimen. 60,000 40,000 20,000 0.002 0.004 0.006 0.008 Strain, in./in. FIGURE P1.14 Determine the following: a. Young's modulus within the linear portion b. Tangent modulus at a stress of 45,000 psi c. Yield stress using an offset of 0.002 strain d. If the yield stress in part c is considered failure stress, what is the maximum working stress to be applied to this material if a factor of safety of 1.5 is used? Stress, psi
The state of stresses in the x and y directions at a point in a given material is shown in the figure below. If the value of the shear stress in the x-y axes Ty is 11 N/mm², find the minimum direct stress that can be found at this point in any possible direction. Round off your answer to the nearest N/mm?. If the answer is negative do insert the "-" sign. 10 N/mm2 Txy 20 N/mm2 20 N/mm2 Ixy 10 N/mm2
6.46 For some metal alloy, a true stress of 345 MPa e (50,000 psi) produces a plastic true strain of 0.02. How much does a specimen of this material elongate when a true stress of 415 MPa (60,000 psi) is applied if the original length is 500 mm (20 in.)? Assume a value of 0.22 for the strain-hardening exponent, n.
The stress concentration occurs whenever there is an abrupt change in the cross-section of a component or there is any discontinuity in the material. The figure given below shows a flat plate with a hole of diameter d. The plate is fixed at one end and the other end is subjected to a tensile load of P = 44 kN due to which there is a change in length of 0.4 mm. The thickness of the plate is 11.5 mm. The maximum stress developed in the flat plate is 228 MPa. Take Young's modulus(E) = 210 GPa and theoretical stress concentration factor =2, Calculate the following values: i) Width of the plate (W2) in mm ( ii) Nominal Stress in MPa ( iii) Diameter of the hole (d) in mm
2. For the state of stress shown, determine the range of value of for which the normal is equal to or less than 100 MPa and 50 MPa. stress x' + 90 MPa 60 MPa =
The following shaft is composed of two materials, both rigidly bonded. The data is provided in the table: Determine: The maximum torque that can be applied based on the maximum stresses of each material. The total deformation of the shaft with the torque from the previous section. The maximum torque that can be applied if the maximum deformation of the shaft is 2.50 rad.
Below is the stress-strain curves of four different materials (A, B, C, and D). Make a brief interpretation of each curve, and rank the materials based on its rigidity. R E STRAIN