Show step by step solutions A beam has a cross-section as shown. At a section where the shear force is 12 kN,a. Determine the moment of inertia using the formula:100 mm| = BH/12 – BH/12)150 mmb. Determine the shear stress distribution at 25-mm intervals along the depthof the beam and label the value, and+ 50 mmc. Plot the shear stress distribution100 mmd. State the locations and the value of the maximum stress found

solution as per the guidelines if the questions are not interlinked we can answer the 1st question…

Answered: 100 mm 150 mm

Engineering

Civil Engineering

100 mm 150 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. Given the following data: Cross section: 50mm x 75mm P = 200 kN e = 15° with the x-axis a. Find the tensile stress (in MPa) on plane A-A. b. Find the shear stress (in MPa) on plane A-A. c. Find the angle (in degrees) of plane A-A in which the shear stress is maximum.
A cube of material (E = 15,000 psi, v = 0.25) of side length 2" is shown in the x, y plane. Takex positive to the right and y positive up. Determine the change in length of the cube in the three coordinate directions if 4 %3D a) The normal stress in the z direction is zero (Ans: 0.0317" in x direction) b) The normal stress in the z direction is 300 psi compression (Ans: 0.0416" in x direction) 150 psi 100 psi + 200 psi
EXAM QUESTION 2 The state of plane stress at a point is represented by the element shown in the figure. (Assume E=210 GPa, v=0.3). Determine a) the principal stresses and the oriented angle associated with the direction of each principal stress using the transformation equations of plane stress; and b) the absolute maximum shear stress at the point according to this stress matrix. 50 MPa 50 MPa 50 MPa
20 ksi 40 ksi 60 ksi The differential element above represents the state of plane stress at a point in a steel beam. Which of the following best represents the magnitude of the second principal stress (02) at the point? 76.6 ksi O 63.3 ksi 36.6 ksi 60.0 ksi
QUESTION 3. The state of plane stress at a point on the tail of Turkey National Combat Aircraft is shown in the figure. Applying both analytical method and the Mohr's cicle, determine a. Determine principal stress values b. Calculate the maximum inplane shear stress and average normal stress. c. Draw the element location for each condition. d. Determine the absolute maximum shear stress value at the same point. 40 MPa TAI 200 MPa 80 MPa
Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 28 MPa, Sy = 39 MPa, and Sxy = 36 MPa. . Determine the maximum normal (principal) stress (in MPa) . Express final answer in 7 significant figures.
1. For the given state of stress, determine the following using the formulas: a. Principal planes 10 Ksi b. Principal stresses c. Orientation of Maximum in-plane shearing stress d. Maximum in-plane shearing stress e. Corresponding normal stress. 2 For the given state of stress, determine the following using Mohr's Circle: 4 Ksi 8 Ksi
Question: In the system shown in the figure, calculate the stress values at points A, B and C under the given loading effect. Choose one of these three points and find the principal stresses and the maximum shear stress that will occur at that point using Mohr's Circle. 100kN 200 mm 500 KN 200 mm - 75 mm 50 rom
For the state of plane stress shown on the right, using a Mohr's circle technique, determine (a) the principal planes, (b) the principal stresses, (c) the maximum shearing stress and the corresponding normal stress. Sketch the results correspondingly on a correctly orientated stress element. 10 MPa -40 MPa 50 MPa
determine the maximum shear stress. sketch thesection stress distribution
QUESTION 4: Draw the three Mohr's circles that describe the following state of stress. Determine the principal stresses, show their orientations and determine the absolute maximum shear stress. 80 MPa 90 MPa
The bar shown in the figure has a square cress section for which the depth and thickness are 40 mm. If an axial force of 800 N is applied along the centroidal axis of the bar's cross- sectional area, determine the average normal stress and average shear stress acting on the material along (a) section plane a-a (b) section plane b-b. a 20 mm 800 N b 60° 20 mm a (a)