11. i) Design a series Op-Amp regulated O/P of 12V which its I/P voltage is 20V. Chose the designed components and draw the circuit diagram ii) Design a shunt transistor regulated O/P of 6V which its I/P voltage is 15V. Chose the designed components and calculate I, with drawing the circuit diagram

11. i) Design a series Op-Amp regulated O/P of 12V which its I/P voltage is 20V. Chose the designed components and draw the circuit diagram ii) Design a shunt transistor regulated O/P of 6V which its I/P voltage is 15V. Chose the designed components and calculate I, with drawing the circuit diagram

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.3P

See similar textbooks

Related questions

Q: H.W: Design Op-Amp circuit to give the following output using 2 op-amps. Vo = -2V₁-3V2 + 4V3 +12V4 +…

Q: Quesi solve the below circuit using the Mesh-Current Method for R₁ = R₂ = R3 = R4 = Rs=R6=R7= R8 =…

A: In the given circuit the value of the mesh current needs to be obtained by using the mesh current…

Q: Sketch Bode plot (magnitude and phase) for H(s) 2(s+1) (s+2)(s+10) where s jw.

A: Given:a system function, we need to sketch:Magnitude and phase Bode plot.

Q: B. Define the following terms with aid of diagrams 1- nondirectional overcurrent relay 2- Biased…

A: "Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: The voltage v(t) shown in Fig. P7.85a is given by the graph shown in Fig. P7.85b. If i(0) = 0, how…

A: The power supplied by a source, such as a battery or a power supply, refers to the rate at which…

Q: Find vo() for all t> 0 in the given circuit. Assume /= 6u(0) A 192 ΙΩ 7u(t) V ww ele www 1 H 0.5 F…

A: The given circuit isWe need to determine the expression of vo(t)=[A+(B)eCtD(Et+(F∘))]u(t) V.

Q: Find all nodes by using nodal analysis

A: The given circuit isWe need to determine the node voltages using nodal analysis.

Q: A 20ohm resistor and a 1μF capacitor are connected in parallel. This parallel combination is…

Q: Given a material with σ = 0.100 S/m, ε₁ = 9.00, and μ₁ = 1.00 and a wave with f= 1.00 GHz, we want…

A: Given a material with;Find the value of

Q: Problem 11: Please find vo(t) if v(t)=20cos(1000t)V using source transformation. v(t) +1 6 Ω 250 με…

A: The objective of the question is to find the output voltage vo(t) for the given circuit using source…

Q: 4 A code C has following generator matrix. G [1 0 0 0 1 1 0 0 0 1 1 0 010010100011 001010010101 0 0…

A: Given:generator matrix for a LBC, we need to find:a) n and k.b) codeword for message [1011]c) decode…

Q: Consider the circuit shown in the given figure. (Given: A = 4.000.) 10 Ω ww 1 H 2 cos 101 V 5H 3H ΑΩ…

A: Average power, also known as real power or active power, is the power consumed by a circuit that is…

Q: Plz correct solution

A: (a) If complemented variables are available the circuit will be take a seconds to be stable because…

Q: Problem 2: Please find the equivalent resistance Req. Each resistor has resistance of 100 2 a. w w…

A: The objective of this question is to find the equivalent resistance (Req) for a set of resistors…

Q: The following systems Y1(s)/F(s) and Y2(s)/F Find the transfer functions. Write the state space…

Q: V V3= 3. Do Problem 3.18. Use NA. The nodes labeled 1, 2, and 3 represent vi, V2, and v3…

A: The circuit diagram,

Q: If the ultimate load is 12.0 tons, find the tensile stress of a mild steel rod of 24 mm diameter?…

A: the ultimate load is = 12.0 tons The diameter of steel rod = 24 mm The Tensile stress is,…

Q: 1. For electric field E = E₁ei(kr-wt), show that B = -V × E = ±k × E. w

A: Curl of E and cross product of wave vector k and E is calculated in cylindrical coordinates.They are…

Q: I need help checking if the Vertical Deflection and Horizontal Deflection that I answer is correct.

A: Given wave form:Find the vertical deflection and horizantal deflection.

Q: Charged particles form a spherical cloud with a radius R0=1m. Within the cloud (R≤R0), the…

A: Total charge is: 4πϵ0R04Total charge density is: 4Rϵ0Explanation:

Q: 11. 13.11 ML Use mesh analysis to find ix in Eig. 13.80, where 12 μF 800 mH HH 150 Ω ww 600 mH + is…

A: Given dataAn electrical circuit consists of resistors, capacitor, and inductors with one current…

Q: For a R-C series circuit if the power commend by the resistance is 500 W at 100V. If the input…

A: The given data is shown below:

Q: Part A In the figure, the total resistance is 14.6 ks, and the battery's emf is 28.4 V. If the time…

A: An RC series circuit is a circuit that contains a resistor (R) and a capacitor (C) connected in…

Q: kll sin(kr-wt); fx 2.| 4π We now want to evaluate the Poynting vector S = ReEx ReH. Taking the real…

A: According to the question, the Poynting vector (S) is given as,We need to prove that

Q: For a hole that is 1.500″–1.508″ mating with a shaft that is 1.475″–1.485″, the limits of clearance…

A: The objective of the question is to find the limits of clearance between a hole and a shaft. The…

Q: BJT Circuit Theory: I have this following circuit but its not producing the correct output. My input…

A: Please refer below pages.If you have any doubts please feel free to ask.Explanation:Step 1: Step 2:…

Q: HE Problem 10: Please use superposition to find v(t) if vs(t) = cos(1000t) V. 50 μF 20 Ω W + v(t) +…

A: The objective of the question is to find the voltage across the resistor v(t) using the principle of…

Q: Find the standard sinusoidal representation of the given phasor. (Express magnitude and phase as…

A: The frequency,

Q: 3. For the following circuit, L₁ = 15 mH, L₁ = 20 mH, and M = 5 mH. Determine the 7-equivalent…

A: The given mutually coupled circuit needs to be converted into equivalent circuit.

Q: 1. A full-wave bridge rectifier isolated from the 220 V rms power line by a transformer. Assuming…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: "*" 15 Ω ww 19.1 mH m 21.22 με 카 N "e" e=250 Sinot + 100 Sin 3ot+45 Sin 5ot+ 15 Sin 7ot+.......…

A: a.) The fundamental frequency of the supply is (ω).b.) The amplitude of this current component is 15…

Q: 444 mH b 720 mH 90 mH 60 mH 240 mH 20 mH (a) HE 80 nF 8 nF 10 nF 48 nF 20 nF b не (b)

A: See the attachments given below for detailed explanation please let me know if you find any…

Q: D Question 6 2/45° 5 Ω -13 N HH Solve for the current i and find its real part (in amps). ΣΖΩ 20 30…

A: Please see the explanation Explanation:Step 1:

Q: R1 R2 R3 A R4 R5 (V) U=27 V, R1=1 Ω R2=1 Q R3=4.7 Q R4=7.3 Q R5=4.8 Ω

A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: draw a three-phase transformer equivalent circuit and also explain how formulas were derived

A: This is a 3 phase transformer equ6 circuit.

Q: A landfill has 18 MW of power generation capacity from biogas combustion. 15 MW of the capacity…

A: Given data:-Total Capacity = 18MWCapacity of Gas engine capacity = 15MWCapacity of ORC process…

Q: Electric Circuits/Two-port: I find all the coefficient values with an explanation of the steps to…

A: y12 should be = -1/6.see the attachment for details.Explanation:

Q: 3. Use Nodal analysis to find (a) current flowing through all the branches in the following…

A: Given:withusing nodal analysis, we need to find:a) current flowing through all branches. b) power…

Q: Determine the (I) rms value up of the following waveforms: a)

A: In the given questions we need to calculate the RMS and average value of the following signal.

Q: Find the currents 11, 12, and i3 if A=25 2, B=75 2, C=25 2, V1=13v, and V2=5 v. V₁ Hint: 10.26857 i1…

A: By Taking the Middle node as V3.By applying Nodal analysis at Node V3,(V3-V1)/A + V3/C + (V3-V2)/B…

Q: LOAD COMPA COMPB 0 pwmA pwmB Same period (frequency), different duty cycles.

A: Please refer below pages. In solution I have taken you through the terms such as:1.Count down…

Q: 2nd problem only

A: The bandwidth is 12Khz, If time multiplex is 24 then bandwidth is 311KHz.Explanation:Problem number:…

Q: Q3 5 Ω 2.5 Ω www www 2A(1 ΣΩ 10 Ω a www 23 10 Ω 1 A www (a) Find the Thevenin Equivalent between a…

A: Given:a circuit,we need to find:Thevenin equivalent between terminals a and b.

Q: Problem 4: Please find Ix using mesh analysis 10 Ω w 25 V + 1 A ww IX 20 Ω w 20 Ω 50 50

Q: Find vol for all t> 0 in the given circuit. Assume /= 2u(t) A. 102 ww 7u(t) V ΙΩ ww + 1 H 0.5 F νο…

A: In the given questions we need to calculate the output voltage.

Q: 4. For the circuit below, the switch has been in position x for a long time. At t = 0, the switch…

Q: Design a 4-1 MUX: 1. Create a 'truth table' for the MUX 2. Generate the logic equations 3. Draw…

A: A multiplexer has 2n data inputs, ‘n’ selection lines, and one output line. Based on selection line…

Q: Question 2 Vin(t) C HH i(t) L R Vout(t) Figure 2 For the R-L-C series circuit shown in Figure 2,…

A: The given circuit isWe need to derivei) The differential equation that relates the input voltage…

Q: Obtain the transfer function E。(s)/E;(s) of the operational-amplifier circuit shown in Figure 6-91.…

A: The given data is shown below:

Q: Ex5 (H.W): For the comparator circuit, if Vin (+) = 13 sin 75.36t, Vref (-) = 7 VDC, VCC=±+15 V,…

A: Given:For a comparator,we need to draw:the output voltage V0.

Question

100%

None

11. i) Design a series Op-Amp regulated O/P of 12V which its I/P voltage is 20V. Chose the designed
components and draw the circuit diagram
ii) Design a shunt transistor regulated O/P of 6V which its 1/P voltage is 15V. Chose the designed
components and calculate I, with drawing the circuit diagram

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: What is operational amplifier

VIEW

Step 2: Series OP-AMP regulator

VIEW

Step 3: Shunt transistor regulator

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 8 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Amplifier circuit is show below has a single ac input and one ac output. Assuming 2N2222 transistor: Construct the T-model of the transistor with all parameters labelled and evaluated. Assume room temperature. Draw a complete small signal circuit model, then find the voltage gain. Explain two characteristics of this amplifier. Calculate the current gain, the input resistance, and the output resistance.
For the cascaded amplifier of the figure below, calculate the input impedance of the first stage, output impedance of the second stage, total voltage gain, and the output voltage if Vs= 1mV.
Amplifier circuit is show below has a single ac input and one ac output. Assuming 2N2222 transistor: 1- Determine the Q point, then illustrate it on the transistor I-V characteristic curves. 2- Is the transistor in the active region? Explain thoroughly. 3- Construct the T-model of the transistor with all parameters labelled and evaluated. Assume room temperature. 4- Draw a complete small signal circuit model, then find the voltage gain. Explain two characteristics of this amplifier. 5- Calculate the current gain, the input resistance, and the output resistance.
THE PAIR of transistors Q1 and Q2 in the figure have gains β1 = 200 and β2 = 75 respectively. Determine the value of the equivalent gain βeq for the equivalent transistor Qeq. ( NEED ONLY HANDWRITTEN SOLUTION PLEASE OTHERWISE DOWNVOTE).
The resistors in the difference ampliﬁer shown are slightly mismatched due to their tolerances. (a) What are the differential-mode and common-mode input voltages if v1 = 3 V and v2 =3V? (b) What is the output voltage? (c) What would be the output voltage if the resistor pairs were matched? (d) What is the CMRR?
Consider the circuit. The transistor has a parameter β that varies between 50 and 200. The operation of the circuit and the electrical variables at the end points must be known. end points. Calculate the following for β = 50 and β = 200. a) lE, VE and VB (DC analysis). b) The input resistance Rin (small signal analysis). c) Voltage gain V0/ Vsig (Small Signal Analysis
For the cascaded amplifier of the figure below, calculate the input impedance of the first stage, output impedance of the second stage, total voltage gain, and the output voltage if Vs=1 mV
Activity 2:The amplifier circuit below has a single ac input and two ac outputs. Assuming transistorparameters of ß = 200 and VBE = 0.7 V:(2-a) Determine the Q point.(2-b) Is the transistor in the active region? Explain thoroughly.(2-c) Construct the T-model of the transistor with all parameters labelled and evaluated.Assume room temperature.(2-d) Draw a complete small-signal circuit model, then find the voltage gain for both outputs.(2-e) Based on the analysis results, what is the function of this circuit? Suggest a properapplication.(2-f) Use Multisim to verify all of your results. Compare and comment.(2-g) Assuming that each output is feeding a 100-kΩ resistor, determine the total voltage gainand current gain for both outputs. Also, calculate the amplifier input resistance and theamplifier output resistances.
amplifier has a gain of unity andVcc= 25Vdc, RL= 8Ω and Vi(p-p)= 34V.a. Calculate the input power, the output powerand the efficiency of the amplifier.b. Consider the operation mode that the two output transistors dissipate the maximum power. For this operation mode, find the output voltage across the load and the power dissipated by each transistor.
Determine the values of the elements of the common-source amplifier as shown such that gain is high and drain current is 11.33 amp.
For the amplifier, VDD = 12V, VSS = 12V, ISS= 20uA, and RD= 820kOhm. Assume Kp = 1mA/V2 and VT P = +1V. (a) What are the output voltages vo for the amplifier for vI = 0V and vI = 20mV? (b) What is the maximum permissible value of vI?
Activity 2:The amplifier circuit below has a single ac input and two ac outputs. Assuming transistorparameters of ß = 200 and VBE = 0.7 V:(2-a) Determine the Q point.(2-b) Is the transistor in the active region? Explain thoroughly.(2-c) Construct the T-model of the transistor with all parameters labelled and evaluated.Assume room temperature.(2-d) Draw a complete small signal circuit model, then find the voltage gain for both outputs.(2-e) Based on the analysis results, what is the function of this circuit? Suggest a properapplication.(2-f) Use Multisim to verify all of your results. Compare and comment.(2-g) Assuming that each output is feeding a 100-kΩ resistor, determine the total voltage gainand current gain for both outputs. Also, calculate the amplifier input resistance and theamplifier output resistances.