24 You want to cool air from 150°C to 60°C but you cannot afford a custom-built heat exchanger. You find a used cross-flow exchanger (both fluids unmixed) in storage. It was previously used to cool 136 kg/min of NH3 vapor from 200°C to 100°C using 320 kg/min of water at 7°C; U was previously 480 W/m²K. How much air can you cool with this exchanger, using the same water supply, if U is approximately unchanged? (Actually, you would have to modify U using the methods of Chapters 6 and 7 once you had the new air flow rate, but that is beyond our present scope.)

24 You want to cool air from 150°C to 60°C but you cannot afford a custom-built heat exchanger. You find a used cross-flow exchanger (both fluids unmixed) in storage. It was previously used to cool 136 kg/min of NH3 vapor from 200°C to 100°C using 320 kg/min of water at 7°C; U was previously 480 W/m²K. How much air can you cool with this exchanger, using the same water supply, if U is approximately unchanged? (Actually, you would have to modify U using the methods of Chapters 6 and 7 once you had the new air flow rate, but that is beyond our present scope.)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An air-conditioning absorption system has an evaporator capacity of 350 kW with a COP of 0.90 operating at a temperature of 25 C with a condensing temperature of 35 C. The same cooling tower was used to reject the heat from the condenser and the absorber operating 45 C & providing 1 kg/s of water plus lithium bromide solution to the generator. Consider the heat rejection ratio of condenser to evaporator is 1.05, Determine the following: 1. Heat given by the generator & the size of condenser in kW 2. Leaving condenser & evaporator enthalpies & the mass of refrigerant water flowing from the generator to the condenser then to the evaporator & to the absorber (using evaporator heat balance). 3. Weight of lithium bromide in kg/s, concentration in percent & enthalpy from the absorber to the generator in kJ/kg 4. Enthalpy from the generator to condenser in kJ/kg (using condenser heat balance) & concentration in percent & enthalpy from generator to absorber…
Water at a rate 68kg/min is heated from 35 to 75℃ by an oil having cp=1.9kJ/kg℃. The fluids are use in a counter flow double pipe heat exchanger, and the oil enters the heat exchanger at 110 and leaves at 75℃. The Over-all heat transfer is 320w/?2℃. Calculate the area. ANSWER: 15.84 m2
In a heat exchanger, the heat transfer depends on the choice of the control volume
i need the answer quickly
What is the heat source? Write briefly. What should be the characteristics of the heat sources used in heat pumps? Write.
2
ercise 6 6.1 A surface condenser is fitted with separate air and condensate outlets. A portion of the cooling surface is screened from the incoming steam and the air is passes over these screened tubes to the air extraction and becomes cooled below the condensate temperature. The condenser receives 20 000kg/hr of dry saturated steam at 36.2°C. At the condensate outlet the temperature is 34.6°C TK and at the air extraction the temperature is 29°C. The volume of air and vapour leaving the condenser is 3.8m3/min. Assume constant pressure throughout the condenser, calculate: 6.1.1 the mass of air removed per 10 000kg of steam (2.63kg); 6.1.2 the mass of steam condensed in the air cooler per minute (0.5kg/min)%3B 6.1.3 the heat rejected to the cooling water (13451kW).
A counterflow heat exchanger operates with hot liquid entering at 200° C and leaving at 160°C. The liquid to be heated enters at 40°C and leaves at 140°C. What is the log mean temperature difference between the hot and cold liquids?
Q5. A simple vapour compression refrigeration system of 60 kW cooling capacity that uses a water-cooled condenser. The power required by the compressor is 10 kW. The overall heat transfer coefficient of the condenser is 350 W/m².K and a heat transfer area of 17 m². If cooling water at a flow rate of 3.5 kg/s enters the condenser at a temperature of 31°C, what is the condensing temperature? Take the specific heat of water as 4.18kJ/kg.K. (20 Marka)
Using the ideas in heat pumps under cyclic process, thoroughly explain the following(with diagram if possible)
Q6 Kindly answer correctly.Please show all the necessary steps