6. The diameters of a pipe at the sections 1 and 2 are 8 cm and 13 cm respectively. Find the discharge through pipe if the velocity of water flowing through the pipe at section 1 is 6 m/s. Determine also the velocity at section 2. a) 2.27 m/s b) 4.54 m/s c) 1.13 m/s d) 3.25 m/s

6. The diameters of a pipe at the sections 1 and 2 are 8 cm and 13 cm respectively. Find the discharge through pipe if the velocity of water flowing through the pipe at section 1 is 6 m/s. Determine also the velocity at section 2. a) 2.27 m/s b) 4.54 m/s c) 1.13 m/s d) 3.25 m/s

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 1. The head of water over an orifice of diameter 100 mm is 8 m. Using C = 0.63 and Cv = 0.98, find…

Q: 4. Two pipes are connected to an open tank of water; pipe A and B have diameters of 8 in and 10 in,…

Q: Compute the discharge of water through 75 mm pipe if the mean velocity is 2.5 m/sec.

Q: A 40-mm-diameter circular pipe carries water at 20°C. Calculate the largest flow rate for which…

A: Given that: Diameter of pipe, d=40mmTemperature = 20°CLaminar flow.

Q: Compute the discharge through a 1000 mm diameter pipe flowing at an velocity of 1.5 m/s.

A: Given: Diameter of pipe, d = 1000 mm Velocity, v = 1.5 m/s

Q: THE MEAN VELOCITY IS 2.5 m/s.

A: Discharge = Velocity ×AreaQ=vA

Q: Water flows from the inlet at point 1 to outlet at point 2 at 0.19 N/s. Assuming steady flow, and…

Q: For the sluice gate shown, if C=0.90 what is the flow rate? If C=0.71 what is the height of the…

Q: Problem 5.2 A 30 cm diameter pipe, conveying water, branches into two pipes of diameters 20 cm and…

Q: Water is flowing through a horizontal pipe of diameter 200 mm at a velocity of 3 m/s. A circular…

A: Given: Pipe diameter, D = 200 mm = 0.2 m Velocity of flow, V = 3 m/s Diameter of solid plate, d =…

Q: Water flows through pipe AB 1.3m diameter at speed of 3m/s and passes through a pipe BC of 1.6m…

Q: A 12" pipe carrying 3.93 ft^3/s connects to a 6" pipe. Find the velocity head in the 6" pipe. a.…

Q: 3. Determine the Velocity and discharge through the 150mm diameter pipe shown a) assuming no head…

Q: A pipeline 2.5 km long and 150 mm diameter supplies water from a reservoir to a small town storage…

A: Given: Length of pipeline Diameter of pipeline Friction factor Difference between water level To…

Q: What volume of flow in ft3/s will pass a 10 inch new cast iron pipe with a head loss of 13 ft per…

Q: Water flows at a rate of 17.0 e/s along a 100 mm diameter pipe AB, which branches at B into three…

A: GIVEN:Discharge =17.0 litre/sec Dia of AB=100mm…

Q: What is the flow rate m3/s inside the pipe if the diameter D=10 cm?

A: Given data : Head (h)=20 mmSpecific gravity (S)=13.6Diameter (d)=10 cm

Q: Water is flowing in a rectangular channel that has a width b=3 m. If the depth of flow y = 2 m and…

Q: 21 31 3Q Figure 1: Two sources flow for (b) (b) Two sources, one of flow rate Q and the other with…

A: Consider the two given sources of positive charge +Q and +3Q As, the flow from each charge is in the…

Q: A new cast iron pipe must carry 1.2 m^3/s at a head loss of 5m per km length of pipe. Compute the…

Q: From reservoir A water is supplied by a pipe that is 12 inches in diameter and 1000 ft long. At…

Q: A cylindrical tank with depth h and radius 1.72m is being filled with water by Pipes 1 and 3. An…

Q: 4.3.2. Determine flow rates in the branching pipe system depicted in Figure P4.3.2 given the…

Q: PROBLEM 3 A pipeline 2.5 km long and 150 mm diameter supplies water from a reservoir to a small town…

Q: Points A and B are 5 km apart along a new 60 cm diameter cast iron pipe carrying water. A is 9m…

Q: Water flows through a vertical contraction (venturi) section. Piezometers are attached to the…

A: Solution; Given that; VA=3m/sρw=density of waterPatm=Atmospheric pressurelet, g=9.81 m/s2

Q: Water flows in a trapezoidal channel with side slope 1V:3H, bottom width of 16 ft and water depth of…

Q: Determine the velocity and pressure at sections 2 and 3 if water flows steadily through the pipe…

A: Use continuity equationA1v1=A2v2π4162×5=π482×v2v2=20ftsecApply Bernoullis theorem betweeen 1 and…

Q: - For the sluice gate shown in figure, if C, = 0.98 and C. 0.62, what is the height of the opening?…

Q: 2) In the figure below, discharge rate at point A is 20 cfs of water. Find the head loss from A to…

Q: Q.07 A reservoir discharges through a sluice 0.915 m wide by 1.22 m deep. The top of the opening is…

Q: 4. A trapezoidal notch of 1.2m wide at the top and 450mm at the bottom is 300mm high. Find the…

A: GIVEN- C=0.60HW=225 mmb1=1.2 mb2=300mm

Q: Water flows through a pipe AB with_m diameter and_ m/s then passes through pipe BC with AB (in cubic…

Q: Find the discharge through a trapezoidal notch which is 1 m wide at the top and 0.4 m at the bottom…

Q: Q1: Find the discharge through the pipe if The diameters of sections (1) and (2) are 25 cm and 30 cm…

Q: A pipe, through which water is flowing, is having diameters, 30cm and 15cm at the cross-sections 1…

Q: Line 1' 3000 m - 300 mm, f = 0.02 Line 2 Y 1300 m – 200 mm, f = 0.02 Line 3 2600 m - 200 mim, f =…

Q: Determine the diameter of steel pipe needed to deliver water (20°C) at a rate of 2 cu. m/s from a…

A: It is said water is flowing from 60 metres to 30 metres, so it is understood that there is energy…

Q: Points A and B are 5km apart along a new 60cm diameter cast iron pipe carrying water. A is 9m higher…

A: Head lossHL=fLv22gDv=QA=Qπ40.6m2HL=0.019×5000mQπ40.6m2229.810.6HL=100.945Q2

Q: 1.9 The volume flow rate through a pipe is given by Q = vA, where v is the average velocity and A is…

A: Given data in question Discharge from pipe 1 Discharge from pipe 2 Velocity of flow through pipe 3…

Q: through D, determine the average velocity of flow through the pipe at A. (Answer: V₁ = 3.68 m/s) 300…

A: To find average velocity through pipe A

Q: Water flows through a one-inch diameter pipe at a velocity of 14.4 ft/s. The pipe divides into two…

A: Solution:Diameter of pipe (D) = 1inch = 0.08333ftVelocity of pipe (V) = 14.4 ft/sec∴ The rate flow…

Q: A 750mm dia. pipe 1162m long carrying 2.4 cubic meter per second of water branches into two pipes,…

Q: Water flows at a rate of 17.0 e/s along a 10 mm diameter pipe AB, which branches at into three…

A: QBE=0.33QBCQAB=171000m3sQBD=5×π4×0.0252=0.0024543m3s

Q: Determine the flow rate through 1000 ft of 8-in.diameter cast-iron pipe (relative roughness…

A: Given head loss=92ftHL=fLV22gDAssume f=0.02292=0.0221000ftV2232.2812ftV=13.399ftsFInd reynolds…

Q: Three pipes are in parallel. The total volumetric flowrate through the network is 2.15 cumecs. If…

Q: In a branching pipe shown, the flow rate in pipe 2 is 40% of pipe 1. Determine (a) size of pipe 2,…

Q: 1.5 m-wide sluice gate with an opening of 10 cm is discharging water at a rate of 3 m/s. Calculate…

A: Given:- B=1.5m a=10cm=0.1m y1=3m y2=2m Cd=0.585 discharge = 3m/s To find:- flow discharge

Q: 0.3 m pipe carries water at a velocity of 24.4 m/s. At points A and B measurements of pressur and…

A: A pipe 0.3m length carries water and the velocity is given. At point A and B the pressure and…

Concept explainers

Asphalt Binders and Mixtures

Asphalt binders are subsidiary products procured during the refining process of petroleum while manufacturing gasoline, diesel, and similar petroleum products. Asphalt binders are obtained from the residue that remains after the distillation of petroleum, this residue is further subjected to steam distillation and oxidation to remove the traces of gas oil present in the residue. Certain additives or modifiers are also added to asphalt binders to alter them to suit different applications.

Question

I need the answer as soon as possible

6. The diameters of a pipe at the sections 1
and 2 are 8 cm and 13 cm respectively. Find
the discharge through pipe if the velocity of
water flowing through the pipe at section 1 is
6 m/s. Determine also the velocity at section
2.
a) 2.27 m/s
b) 4.54 m/s
c) 1.13 m/s
d) 3.25 m/s

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A pipe system has a flow of 4.6 cfs. Section 1 has a diameter of 12” and Section 2 has a diameter of 10”. What is the velocity at each section? A. Section 1: 5.89 ft/sec Section 2: 9.2 ft/sec B. Section 1: 8.9 ft/sec Section 2: 6.0 ft/sec C. Section 1: 9.9 ft/sec Section 2: 9.9 ft/sec D. Section 1: 4.89 ft/sec Section 2: 6.58 ft/sec
3. Determine the Velocity and discharge through the 150mm diameter pipe shown a) assuming no head loss and b) considering a head loss of 200mm El. 30 El. 28 m El. 27.5 m 150 mm El. 24.9 m
A 600m long pipe with a diameter of 600mm has a headloss of 1.20m. Determine the following: a.) Discharge flowing in the pipe, f = 0.012; b.) Discharge flowing in the pipe, n = 0.014; c.) Discharge flowing using C = 120 im iong PIune tnat Tuns on
A 0.60 m. dia. pipe 600 m. long has a head loss of 1.2 m. Find the discharge flowing in the pipe using f = 0.012. a) 0.614 m³/s c) 0.574 m³/s b) 0.418 m³/s-d) 0.396 m³/s 2 Find the discharge flowing in the pipe using n = 0.014. 0.254 m³/s c) 0.124 m³/s b) 0.326 m³/s d) 0.478 m³/s Find the discharge pipe using C= 120. flowing in the a) 0.305 m³/s c) 0.614 m³/s b) -0.582 m³/s d) 0.478 m³/s
A 0.60 m. dia. pipe 600 m. long has a head loss of 1.2 m. Find the discharge flowing in the pipe using f= 0.012. a) 0.614 m³/s c) 0.574 m³/s b) 0.418 m³/s-d) 0.396 m³/s Find the discharge flowing in the pipe using n = 0.014. 0.254 m³/s c) 0.124 m³/s b) 0.326 m³/s d) 0.478 m³/s Find the discharge pipe using C = 120. a) 0.305 m³/s b) -0.582 m³/s flowing in the c) 0.614 m³/s d) 0.478 m³/s
For the Pipe T shown, determine the discharge from pipe 2. 5 ft/s 1 6" 3 3" 7 ft/s 6" 2 ?
Determine the discharge for pipe network at each branch 1524 m, 305mm Q = 0.513 m /s A B 915 m, 406mm
A 750mm dia. pipe 1162m long carrying 2.4 cubic meter per second of water branches into two pipes, 450mm dia. and 600mm dia. at junction A. The 450mm pipe is 1254m long and the 600mm is 1196m long. They come together at junction B and continue as a single pipe 750mm in diameter and 866m long. Assuming the values of fare 0.017, 0.019, and 0.020 respectively for the 750mm, 600mm, and 450mm pipes. What is the discharge in the 450mm pipe?
Q4: Assuming f-0.020, determine the discharge in the pipes. Neglect minor losses. Pipe Diameter AB 250 mm 200 mm 400 mm BC BD Length 1200 m 600 m 200 m EL.45m EL 3m. B C EL. 3.0m D EL 0.0m
Table 1 shows the data for the network of pipes connecting four reservoirs to a common junction, J. Table 1 8fL r = gπ2p5 4.0 Reservoir Water Reservoir Pipe Level (m) A 50 AJ B 45 BJ 3.0 C 40 CJ 2.0 D 30 DJ 2.0 а) Sketch the pipe network together with the four reservoirs as described above and show the directions of flow based on the initial assumption of the head at the junction J of 41 m. State two hydraulics principles that need to be fulfilled in the analysis of this pipe network. b) Calculate the discharge in each pipe. Compute your answer to two decimal places only.
Determine the discharge at pipeline 3 in lit/sec assuming f=0.02 for all pipes. 700 m 450mm diam. 0.86m3/s Pipe 2 800 m 400mm diam. Pipe 3 700 m 500mm diam. O 373 733 О 133 О 311
With the given pipe lengths, sizes and connections and if all pipes have an f=0.020, determine the flow in each pipe if the total head loss between A and D is 150 ft. 3250 ft of 12 in Situation 6: 2 2750 ft of 21 in 2250 ft of 10 in 4750 ft of 27 in A 1+ B C 5 D 3 2750 ft of 14 in 4 -