7.60. Water is to be pumped from a lake to a ranger station on the side of a mountain (see figure). The length of pipe immersed in the lake is negligible compared to the length from the lake surface to the discharge point. The flow rate is to be 95 gal/min, and the flow channel is a standard 1-inch. Schedule 40 steel pipe (ID = 1.049 inch). A pump capable of delivering 8 hp (= Ws) is available. The friction loss F (ft-lb/lbm) equals 0.041L, where L(ft) is the length of the pipe. (a) Calculate the maximum elevation, z, of the ranger station above the lake if the pipe rises at an angle of 30°. (b) Suppose the pipe inlet is immersed to a significantly greater depth below the surface of the lake, but it discharges at the elevation calculated in Part (a). The pressure at the pipe inlet would be greater than it was at the original immersion depth, which means that AP from inlet to outlet would be greater, which in turn suggests that a smaller pump would be sufficient to move the water to the same elevation. In fact, however, a larger pump would be needed. Explain (i) why the pressure at the inlet would be greater than in Part (a), and (ii) why a larger pump would be needed. 30°

7.60. Water is to be pumped from a lake to a ranger station on the side of a mountain (see figure). The length of pipe immersed in the lake is negligible compared to the length from the lake surface to the discharge point. The flow rate is to be 95 gal/min, and the flow channel is a standard 1-inch. Schedule 40 steel pipe (ID = 1.049 inch). A pump capable of delivering 8 hp (= Ws) is available. The friction loss F (ft-lb/lbm) equals 0.041L, where L(ft) is the length of the pipe. (a) Calculate the maximum elevation, z, of the ranger station above the lake if the pipe rises at an angle of 30°. (b) Suppose the pipe inlet is immersed to a significantly greater depth below the surface of the lake, but it discharges at the elevation calculated in Part (a). The pressure at the pipe inlet would be greater than it was at the original immersion depth, which means that AP from inlet to outlet would be greater, which in turn suggests that a smaller pump would be sufficient to move the water to the same elevation. In fact, however, a larger pump would be needed. Explain (i) why the pressure at the inlet would be greater than in Part (a), and (ii) why a larger pump would be needed. 30°

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4) A pump operates at 2000 rpm and delivers 200 gal/min at 90 ft head. The water distribution operator is requested to increase the head and flow in the network due to a leak. He increased the pump speed to 2160 rpm. What are the corresponding head and discharge?
7.45 If the fluid motor has an efficiency of 78 percent, how much power is delivered by the motor? 15-in Schedule 80 steel pipe 25-in Schedule 80 steel pipe Oil -Motor Flow 38.5 in Mercury sg = 13.54 Answer is 1.24 Hp. Please shw how to get ture.
6. A pump draws water from a sump through a vertical 6" pipe. The pump has a horizontal discharge pipe 4" in diameter that is 10.6 ft above the water level in the sump. While pumping 1.25 cfs, gages near the pump at entrance and discharge read -4.6 psi and +25.6 psi, respectively. The discharge gage is 3.0 ft above the suction gage. Compute the horsepower output of the pump and the head lost in the 6" suction pipe.
7. A large tank is partly filled with water, the air space above being under pressure. A 2" hose connected to the tank discharges on the roof of a building 50 ft above the level in the tank. The friction loss is 18 ft. What air pressure must be maintained in the tank to deliver 0.436 cfs on the roof ?
Include a free body diagram. pump draws water from a sump through a vertical 6′′ pipe. The pump has a horizontal discharge pipe 4′′ in diameter that is 10.6 ft above the water level in the sump. While pumping 1.25 cfs, gages near the pump at entrance and discharge read —4.6 psi and +25.6 psi, respectively. The discharge gage is 3.0 ft above the suction gage. Compute the horsepower output of the pump and the head lost in the 6′′ suction pipe. (ANSWER: 10.7 Hp, 2.4 ft)
Problem 3. Two reservoirs are connected by a pipe whose diameter is D=0.15 m and geometry as reported in figure 2. The difference in water (kinematic viscosity v =10“m²s', density p=1000 Kg/m³) elevation (AH) between the two reservoirs is 8 m. a) Qualitatively sketch the Hydraulic Grade Line and the Energy Grade Line of the flow within the pipe. b) Compute the flow rate within the pipe assuming the equivalent sand roughness to be e=0.4 mm. ΔΗ 1m 25m 4m
1 QUESTION 1 Consider a desired pump operating condition which adds 35 psi at a flowrate of 500 gpm to water (p= 62 11m/ft²³) Ignore any changes in Kinetic or potential energy and Tassume isothermal flow C.e. internal energy is constant, this is the normal assumption we make when analyzing fluid flows in piping systems). Apply the energy balance only across the pump with full energy Balance and simlifying to solve for the pump, Starting head symbolically. Then begin careful of units, Solve for pump head in feet. GIVEN: 35psi 500 gpm p=62 1bm/3 XA. 10.5 A B. 100.8 ft C. 50.1 ft D. 80.7f 35 500 62 (32.2) + 2(32.2) 35 + 500
QUESTION 3 A submersible deep-well pump delivers 250L/min of water through a 1-in Schedule 40 pipe when operating in the system sketched in Fig. 3. An energy loss of 2.3 m occurs in the piping system. (a) Calculate the power delivered by the pump to the water. (b) If the pump draws 1 hp, calculate its efficiency. A 27 kba 12 m
8. A pumped fluid distribution system is being designed to deliver 400 gal/min of water to a cooling system in a power generation plant. Use the figure below to make an initial selection of Schedule 40 pipe sizes for the suction and discharge lines for the system. Also, solve for the actual average velocity of flow for each pipe. DN (mm) NPS (in) 250 200- 150 - 6 125- Suction lines 100 - 4 3. 65 2 50E 2 Discharge lines 40 - 32 - 25 E 15 15 20 30 40 60 200 400 600 S00 2000 4000 6000 S00 80 100 10 Volume Flow Rate, Qallmin) 8 10 15 20 25 30 40 +++++ +++ 60 80 100 150 200 300 400 500600 800 1000 1200 2000 +++++ +++++ Volame Flow Rate, Q (mVh)
FROM THE ATTACHED SKETCH, THE GIVEN DATA ARE AS FOLLOWS: Pressure loss due to friction a. Reservoir tank =50,000 liters of water b. Total Static head is 30 ft. Pressure loss in plastic pipes (feet of water per 100 ft of tube) c. Pipe material is plastic and 1.5-inch diameter. d. There are four 90-degree elbows, one gate valve and one open swing spm 0.5 in. 0.75 in. 1 in. 1.5 in. 2 in. 3 in. 1.4 4.8 0.0 0.0 0.0 0.4 0.1 0.4 0.8 1.3 1.9 2.7 0,0 0.0 valve. 0.0 1.2 2.5 4.2 6.3 8.8 15.2 26.0 49.7 86.9 e. Total pipe length is 50 ft. 3 0.0 10.0 17.1 25.8 36.3 63.7 97.5 0.0 0.1 0.2 0.2 0.3 4. 0.0 0.0 5 0.0 0.0 0.0 0,0 0.0 6 0.1 0.2 0.3 0.5 0.9 0.1 COMPUTE THE FOLLOWING USING THE PROVIDED TABLE BELOW. 8 4.6 0.6 10 15 20 6.9 14.6 0.8 1.7 2.9 0.0 25.1 1. IF THE TANK IS TO BE FILLED WITHIN 661.35 MINUTES WHEN EMPTY, COMPUTE HOW MANY GALOONS PER MINUTE (GPM) PUMP CAPACITY IS NEEDED TO FILL UP THIS TANK., USE 3.78 LITERS/GAL Pressure loss in valves and elbows (expressed in equivalent length of tube)…
A) Calculate by hand the net head delivered and the efficiency of the pump at flow rate of 63 L/s. B) Use excel sheet and its formula to solve the equations and plot the pump head, power input, and efficiency versus the pump flow rate
8.) A liquid having a sp.gr. of 20 is flowing in a 50 mm diameter pipe. The total head at a given point was found to be 17.5 Joule per Newton. The elevation of the pipe above the datum is 3 m and the pressure in the pipe is 65.6 kPa. Compute the velocity of flow and the horsepower in the stream at that point. Subject: Fluid Mechanic Lesson: Relative Equilibrium of Liquids Fundamentals of Fluid Flow