A 22.2 mm diameter bolt having a diameter at the root of the threads of 18.6 mm is used to fasten two timbers as shown in figure below. The nut is tightened to cause a tensile load in the bolt of 34 KN. Determine a) the shearing stress in the head of the bolt. B) the shearing stress in the threads, and C) the outside diameter of the washers if their inside diameter is 28 mm and the bearing stress is limited to 6 MPa. 12 mm 16 mm

A 22.2 mm diameter bolt having a diameter at the root of the threads of 18.6 mm is used to fasten two timbers as shown in figure below. The nut is tightened to cause a tensile load in the bolt of 34 KN. Determine a) the shearing stress in the head of the bolt. B) the shearing stress in the threads, and C) the outside diameter of the washers if their inside diameter is 28 mm and the bearing stress is limited to 6 MPa. 12 mm 16 mm

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.12.2P

See similar textbooks

Similar questions

Considering the following steel connection. The plates in Pink are 9mm steel plates. The middle plate (Yellow) is 18mm thick. The width of the plate is 100mm. The maximum allowable tension stresses on any of the plates is 100Mpa in Gross Area Yielding and 150 Mpa for Net Area or Tension Rupture. The bolts used are 8mm in diameter, the holes are 10mm in diameter, no need to add 1.6mm. The bolts allow a maximum of 280 Mpa of shear. Determine the maximum allowable "P" of the connection in kN.
A bolted connection shown consists of two plates 300mm x12mm connected by 4 - 22 mm diameter bolts. Edge distances = 75mm dhole for tensile and rupture = db + 3 mm dhole for bearing strength for Lc = db + 1.5 mm Fy = 248 Mpa Fu = 400 Mpa Fn = 330 Mpa Use LRFD design method. Determine the design strength due to the gross yielding of plates. (kN)
A 15" x 3/8" bar of A572 Gr. 50 steel is used as a tension member. It is connected to a gusset plate with 7/8-in diameter bolts as shown in the figure. Use s = 2.0 and g = 3.0.a) Determine the design tensile strength of the section based on yielding of the gross area.b) Determine the critical net area of the connection shown.
3. A plate with width of 300mm and thickness of 20mm is to be connected to two plates of the same width with half the thickness by 24mm diameter bolts, as shown. The rivet holes have a diameter of 2mm larger than the rivet diameter. The plate is A36 steel with yield strength F,-248MPa and ultimate strength F,-400MPa. a. Determine the design strength of the section. b. Determine the allowable strength of the section 24mm 30mm
The following image shows a front and side view of the column connection. The bolts have a diameter of ¾”. The W12X65 profile has a thickness of 0.605”. Determine:a. The shear stress in the bolts.b. The axial stress in the bolts.c. The support stress in the W12X65 profile.
Topic:Bolted Steel Connection - Civil Engineering *Use latest NSCP/NSCP 2015 formula to solve this problem *Please use hand written to solve this problem The bracket shown in the figure is supported by four 22 mm diameter bolts in single shear. The bracket is subject to an eccentric load of 150 kN. Use LRFD. Use A36 steel. Questions a) Determine the critical force on the most stressed bolt. b) Determine the nominal shear stress of the most stressed bolt.
The plate with dimension 18 mm x 400 mm (thickness by width) is to be connected to a gusset plate using 6-Ø24 mm bolts in arrange in 3 row (2 each row) along the x-axis. The plate is to be design for tension. Using A36 steel and assuming Ae= An. Use NSCP 2015. a. Compute the design strength considering yielding and tensile rupture. (LRFD) b. Compute the allowable strength considering yielding and tensile rupture. (ASD)
Determine the design tensile strength of plate (200x8 mm) connected to 10-mm thick gusset using 20 mm bolts as shown in the figure, if the yield and the ultimate stress of the steel used are 250 MPa and 410 MPa, respectively. Add 1mm around the bolt for the hole. Use LRFD method. Plate 8-mm thick 2 3 40+ 30 301 T 200 mm Gusset 10-mm thick 3af 30 2_3 *40 40+ 50,54 +40
A 16 mm thick tension member is connected by two 6.25 mm spliced plates as shown. The tension member carries a service loads of dead load of 110 kN and a live load of 100 kN. 40, 80 , 40 , 40, 80 40 1625 mm 16 mm 1625 mm Fy 248 MPa Fu = 400 MPa Diam. of bolts = 16 mm Fnv = 300 MPa O Determine the nominal strength for one bolt due to shear. O Determine the nominal strength for one bolt due to bearing strength of the connection. ® Determine the number of bolts required for the connection.
2. See connection figure below. The rivets is 7/8 in. in diameter. According to the rivert supplier, the allowable stresses for the material are t = 15 ksi and on = 32 ksi. What is the allowable load of the connection? L4 x 3-1/2 W18 x 86 W24 x 117 Girder Beam
The plate with dimension 18 mm x 400 mm (thickness by width) is to be connected to a gusset plate using 6-Ø24 mm bolts in arrange in 3 row (2 each row) along the x-axis. The plate is to be design for tension. Using A36 steel and assuming A= An. Use NSCP 2015. a. Compute the design strength considering yielding and tensile rupture. (LRFD} b. Compute the allowable strength considering yielding and tensile rupture. (ASD)
Two flat bars loaded in tension by force P are spliced using two rectangular splice plates and two 0.350 in. diameter bolts. Away from the connection, the bars have a width of b = 0.625 in. and a thickness of t = 0.15 in. The bars are made of polyethylene having an ultimate tensile strength of 3200 psi and an ultimate bearing strength of 1500 psi. The bolts are made of nylon that has an ultimate shear strength of 4400 psi. Determine the allowable load P for this connection if a safety factor of 3.7 is required. Consider tension and bearing in the bars and shear in the bolts. Disregard friction between the plates.