a) Calculate the small-signal gain A, the input resistance Rin, and the output resistance Rout for a single stage. b) Calculate the overall gain of the circuit. Do the calculation in two parts. First calculate the system gain of the first stage Gj using the input resistance of the second stage as the load. Then calculate the system gain of the second stage G2 using the output resistance of the first stage as the signal source resistance. The total gain is then G = G¡G2.

a) Calculate the small-signal gain A, the input resistance Rin, and the output resistance Rout for a single stage. b) Calculate the overall gain of the circuit. Do the calculation in two parts. First calculate the system gain of the first stage Gj using the input resistance of the second stage as the load. Then calculate the system gain of the second stage G2 using the output resistance of the first stage as the signal source resistance. The total gain is then G = G¡G2.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Consider the circuit in Figure 2. The transistor has a parameter B that varies between 50 and 200. You want to know the operation of the circuit and the electrical variables at the end points. Calculate the following for B= 50 and B= 200. a) IE, VE and VB (Analysis in DC). b) The input resistance R." (Small signal analysis). c) The voltage gain VO/Vsing (Small signal analy). This 10 ΚΩ www o Rin 100 ΚΩ +3V +1₁ HH 1 ΚΩ 1₁ 1 ΚΩ
The DC Current Gain of a Transistor is Select one: a. Ratio of Collector Current to Base Current b. Ratio of Base Current to Collector Current c. Ratio of Emitter Current to Collector Current d. Ratio of Base Current to Emitter Current
Draw, Illustrate and label your schematic diagram before solving the problem. 3) Given an Emitter-Stabilize Biased transistor circuit with beta DC is 250,Base resistor is 150 ohms, collector resistor is 1.5k ohms ,emitter resistor is 500 ohms ,emitter voltage supply is -5v and Voltage at common collector is +28V,Voltage at Base-emitter junction is 0.7v,. Determine Base current, Collector current and Voltage at collector-emitter junction.
1 The AC input to a common emitter amplifier (Figure 1) is such that it is comparable to thermal voltage VT. For such an amplifier: a. Please show how a hybrid – T small-signal model would look like. Do not ignore early effect. b. Please derive relation for the terminal voltage gain and overall voltage gain. Vcc Rc R RE C Figure 1 You uolont oirouit
ASAP
Exersice 4: For the Darlington amplifier circuit used in an emitter-follower configuration appears in figure below: . Determine the dc levels of Vi, Ve, Vi, Ves, and Ver. . Find the currents I, Iz, and Irz. . Calculate Zi and Zo. . Determine the voltage gain Ay = Vo/Vi and current gain Ai=IL/l;. . Repeat parts 1 to 4 with a load resistor of 1.2 kQ. . Evaluate A = Vo/Vs if the source has an internal resistance of 1.2 kQ and the applied load is 10 kQ. omAwWNE 416V L i prammm, I Tour i,
4 For the transistor shown in below figure, Calculate the value of R; that will just make the transistor work as closed switch. Hence Bpc = 80, VBE = 0.7V, VCE(sat) = 0.2V, Vcc = 12V, R. = 2.7KN. a) Calculate the I, and I.. Vcc RB Rc b) Calculate Rp.
9. Design a biased-transistor circuit using VBB = Vcc= 10 V for a Q-point of Ic = 5 mA and VCE 4 V. Assume pc = 100. The design involves finding RB, RC, and the minimum power rating of the transistor. (The actual power rating should be greater.) Sketch the circuit.
Figure 3 shows two current mirrors based on MOSFET. Derive a formula relating the input current In to the output current Iout for the current mirror on the left of Figure 3 stating any assumption. (a) (b) Derive the input resistance Rin and output resistance Rout for the circuit on the left of Figure 3. State any assumption. (c) Derive a formula relating In and Iout for the circuit on the right of Figure 3 assuming that Mi and M2 are identical, and that the length and width of the channel for the transistor M4 are double respect to those of M3. State any assumption. V DD M. M4 M1 M2 M1 M2 V'ss =0 V Vss=0 V Figure 3
Activity 2: The amplifier circuit below has a single ac input and two ac outputs. Assuming transistor parameters of B= 130 and VBE=0.7 V: 15 V 15 V W 350 ΚΩ 300 ΚΩ H11 13 ΚΩ 10 ΚΩ
How to calculate the bias resistor of a common emitter amplifier. The design curretn is 0.55mA. Bera is assumed to be 200 and the Vcc = 12V. Note: the bias resistor should be high.
True or False(a) The output Vo is in-phase with the input Vi if the cascaded amplifier consists of two common-emitteramplifier stages.(b) The current gain, voltage gain, and output impedance are all relatively high for a cascaded amplifier consisting of two common-emitter amplifier stages.(c) The input impedance and voltage gain of a common-emitter amplifier is higher if a bypass capacitor is connected across the emitter resistor.