A closed cylindrical tank 2m in diameter and 7m high has 3m tall of water and 3m of oil (SG = 0.8). The surface of oil is under a pressure of 40 KPa. The orifice is located at the vertical side of the tank and it is 1m above the bottom of the tank. If the jet strikes the ground 1.5m below the vena contracta and Cv = 0.92, determine a) the theoretical velocity and b) The horizontal distance from the vena contracta to the point where the jet strikes the ground. (This is a multiple answer question. You must have 2 selected choices since there are 3 required answers in the problem)

A closed cylindrical tank 2m in diameter and 7m high has 3m tall of water and 3m of oil (SG = 0.8). The surface of oil is under a pressure of 40 KPa. The orifice is located at the vertical side of the tank and it is 1m above the bottom of the tank. If the jet strikes the ground 1.5m below the vena contracta and Cv = 0.92, determine a) the theoretical velocity and b) The horizontal distance from the vena contracta to the point where the jet strikes the ground. (This is a multiple answer question. You must have 2 selected choices since there are 3 required answers in the problem)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2-An open tank 6 m long, 2.4 m deep and 3.6 m wide contains oil of specific gravity 0.85 to a depth of 1.2 m. If the tank is accelerated along its length on a horizontal track at a constant acceleration of 3.2 m/s2. Determine:(i) New position of oil surface(ii) Pressure at the bottom of tank at the front and rear edges. 1.2 m New oll surface B 8 6m Original free oil surface U (3.2 m/s) M
An oil is flowing between two parallel horizontal plates which are 20 mm apart. The top plate is moving witha uniform speed 0.1 m/s. The viscosity of the oil is 0.1 N s/m2. The velocity at the centerline is 1.95 m/s.Consider the flow to be a fully developed one.a) Derive the velocity profileb) Calculate pressure difference between two points (P1-P2) 5 m apartc) Find the velocity at 3 mm from the wall of the bottom plates.d) Find the velocity at 3 mm from the wall of the top plates.e) Determine force acting on the bottom wall, (W=10 cm)
A closed cylindrical tank 2m in diameter and 7m high has 3m tall of water and 3m of oil (SG = 0.8). The surface of oil is under a pressure of 40 KPa. The orifice is located at the vertical side of the tank and it is 1m above the bottom of the tank. If the jet strikes the ground 1.5m below the vena contracta and Cv = 0.92, determine a) the theoretical velocity and b) The horizontal distance from the vena contracta to the point where the jet strikes the ground. (This is a multiple answer question. You must have 2 selected choices since there are 3 required answers in the problem) A) Vt = 10.04 m/s B Vt = 10.91 m/s horizontal distance = 7.13 m D) horizontal distance = 6.03 m No answer among the choices in question B Vt = 12.90 m/s G) horizontal distance = 5.55 m horizontal distance = 6.56 m No answer among the choices in question A
Q9) A U - tube is made up of two capillaries of bores 1.2 m and 2.4 mm respectively. The tube is held vertical and partially filled with liquid of surface tension 0.06 N / m and zero contact angle. If the estimated difference in the level of two menisci is 15 mm, determine the mass density of the liquid.
2. An oil is flowing between two parallel horizontal plates which are 20 mm apart. The top plate is moving with a uniform speed 0.1 m/s. The viscosity of the oil is 0.1 N.s/m². The velocity at the centerline is 1.95 m/s. Consider the flow to be a fully developed one. a) Derive the velocity profile b) Calculate pressure difference between two points (Pi-P2) 5 m apart c) Find the velocity at 3 mm from the wall of the bottom plates. d) Find the velocity at 3 mm from the wall of the top plates. e) Determine force acting on the bottom wall, (W=10 cm) 0.1 m/s Oil P1 P2 2 cm y 5 m
A closed tank has an orifice in the vertical side with diameter of 70mm. Thehead of oil having a specific gravity of 0.92 is 2m above the orifice. If there isa pressure of 15kpa at the top of the oil surface inside the tank, compute theheadloss in the orifice with Cv = 0.96.
Two vertical circular cylindrical tanks are connected near the bottom by a short tube having a cross-sectional area of 725 cm2. The inside diameters of the tanks are 3m and 1.5 m, respectively. The tanks contain oil. With the valve in the tube closed, the oil surfaces are 4m in the larger tank and 0.6 m in the smaller above the tube. With c=0.78, find the time required for the surfaces to equalize following a quick opening of the valve. Assume the properties of the tube to be similar to that of an orifice. 15.25 s 20.81 s 22.58s 39.28 s
diameter = 2 meters The vertical cylindrical tank has 4 m high of water. The centerline of the standard orifice is 3.2 meters above the ground and 3.5 meters below the liquid level surface. Cv = 1.0 * What is the horizontal distance reached by the jet?
A 1.90m diameter closed cylinder, 2.75m high is completely filled with oil having sp.gr. of 0.8 under a pressure of 5 kg/cm^2 at the top. a. What angular speed (RPM) can be imposed on the cylinder so that the maximum pressure at .90 m from the center of the tank is 14 kg/cm^2 ? b. If the cylinder is open what is the maximum angular speed (RPM) can be imposed so that the water touches the bottom of the tank?
... Elevation 15.25m Elevation 14 m water Elevation 10.7m 30° An orifice in a 30 degree plane from horizontal as shown has its vena contracta at elevation 10.7m. If the water surface in the tank is at elevation 15.25m and the peak of the jet is at elevation 14m. Find the coefficient of velocity. 0.983 B) No answer among the choices 0.952 D 0.964 0.975
A pipe carrying oil of sp gr 0 877 changes in A pipe carrying oil of sp gr 0.877 changes in size from 150mm at section E to 450mm at section R Section E is 3 66m lower than R section R. Section E is 3.66m lower than R and the pressures are 91.0kPa and 60.3kPa, respectively. If the discharge is 0.146m3 respectively. If the discharge is 0.146m /s, determine the lost head and the direction of flow.
A type of oil [SG = 0.85 , visco = 211cP] is pumped at a rate of 86 ft^3/hr from an open reservoir to the bottom of another open tank. The liquid level in the reservoir and the bottom of the discharge tank are vertically 17 feet apart. Friction losses in the pipe total to 7.5% of the elevation head. If the goal is to keep the level of liquid in the discharge tank at a constant 4.5 feet, calculate the theoretical power requirement of the process in ft lbf /s. If the pump has an efficiency of 65 %, calculate the actual power requirement.