A converging nozzle having an exit diameter of 30 mm isconnected to the large tank (Figure 1). The absolute pressureoutside the tank is 102 kPa.FiguremIf the temperature of the air in the tank is 20°C and the absolute pressure is 380 kPa, determine the mass flow from the tank.Express your answer using three significant figures.5. ΑΣΦ 11 vecSubmitRequest Answer?< 1of 11 of 1 >kg/sA

Answered: Image /qna-images/answer/8cb320e0-ca1d-4d5a-bbe5-1264eb715c1e.jpg

Answered: A converging nozzle having an exit…

A converging nozzle having an exit diameter of 30 mm is connected to the large tank (Figure 1). The absolute pressure outside the tank is 102 kPa. Figure < 1 of 1 >

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: a) If the pipe connected to the pump inlet has a diameter of 24 mm with length (LCP) of 5 m and…

Q: Item 3 The two ropes shown in the bird's-eye view of (Figure 1) are used to drag a crate 4.7 m…

Q: The 3D printing approach shown below is fused deposition modelling (FDM), where feedstock polymer is…

Q: The coordinate axes in the figure run through the centroid of a solid wedge parallel to the labeled…

Q: Refrigerant R12 is used in a vapour compression cycle. The saturated vapour enters the compressor at…

A: Given data :- The Specific enthalpy h,The specific entropy, s, at 10 bar to be 1.188 kJ/kgTo…

Q: As an engineer you are presented with an electronic device design with a thin flat ceramic plate in…

A: The coefficient of thermal expansion (CTE) is a crucial property that measures how a material's…

Q: Milk stored in a storage truck is to be extracted using a pump using a pipe. Given, unit weight of…

A: Unit weight of milk is 1030 kg/m3 and viscosity of 1.7 centi PoiseBased on the roughness condition…

Q: i[71] [54] k[22] Define the unit vector between the 2 points in the form of (#i,#j,#k) (Round to two…

Q: Air at a temperature of 20°C and standard atmospheric pressure of 102 kPa flows through the nozzle…

A: Temperature = 20°CAtmospheric pressure= 102kPaPressure in pipe = 60kPaDiameter = 11mmFind the mass…

Q: 2) Determine the reaction forces at ball-and-socket joint A and the tensions in the three support…

Q: 4 45,000 lbs 72' Temperature changes from 55° F to 275 F -2.25 45,000 lbs California Redwood F.S.= 4…

Q: For the frame shown, Knowing that the pulley has a radius of 0.5 m, determine the components of the…

A: Given: Radius =- o.5 mTo determineComponents of the reactions at A and E

Q: Question 1 This question requires the use of the Thermodynamic Property Tables supplied as…

Q: Problem 3: The rod below has a diamter of 2 in. Determine the state of stress at point A, and show…

A: The diameter of rod is

Q: Bar OC rotates with a clockwise angular velocity woc = 5.3 rad/s and a counterclockwise angular…

Q: Question 4 The window of a room is made of 5 mm thick glass which has a thermal conductivity of 1.4…

Q: 4. Consider the system shown below. Let K-2 N/m, C- 2 kg/s, M = 1 kg, x(0)=-0.1 m, and v(0) = 1 m/s.…

A: The mass is .The spring constant is .The damping constant is .The intial condition are .

Q: The 0.39*0.81-m lid ABCD of a storage bin is hinged along side AB and is held open by two cords ED…

A: Write the given data.

Q: Consider a defect in a crystalline lattice as shown below. Which of the following statements is…

A: When a molecule (B) is slightly larger than the other molecules in a crystalline lattice, it…

Q: Bar AC supports two loads, X = 355 N and Y= 355 N as shown. Rollers at A and Crest against…

Q: Task 1 It is required to design a tennis ball for recreational use by settlers on Mars. The primary…

A: Given data:LE - Drop height on Earth (m) = 2.54 m gE - Gravitational acceleration on Earth (m/s2) =…

Q: A thin-walled tube has its inner surface coated with polypropylene lining. The ASME Code for Process…

A: Given Data

Q: An unknown polymer sample was found to have the following molecular weight distribution: Molecular…

A: Given:Molecular weight distribution tableDP = 763

Q: B: Set an expression for heat transfer rate through plane wall with thickness L and thermal…

Q: A filled barrel has dimensions of a = 0.55m, b = 1.1m, and c = 0.6m, a total mass of 108kg, and has…

Q: You are designing an industrial furnace to keep sheet metal at a fixed temperature. You decide a…

A: It is asked to find the heat input per unit length

Q: In the region indicated with arrows in the phase diagram shown below (above the upper line), which…

Q: 3 m 500 N/m 1.5 m A 2 m F D B 2 m 900 N Show Transcribed Text E ΤΟΙ·ΙΟΣ 750 N 3 m determine a- the…

Q: What is the maximum length of a uniformly loaded beam based on the maximum allowable stresses, it's…

A: maximum allowable stressesit's normal stress shear stress based on the maximum allowable stresses,…

Q: The weights of the uniform thin pin-connected bars AB, BC, and CD are WAB=4 lb, WBC= 6.5 lb, and…

Q: Determine the moment created by the weight of the suspended sign about point O. The dimensions of…

A: Given that Thickness, t = 2 mm = 2 x 10-3 m Length, l = 2m Breadth, b = 1m To determine…

Q: Q5)A shaft 100mm diameter is subjected to a twisting moment of 7kNm, together with a bending moment…

Q: earning Goal: To understand the derivation of the law relating height and pressure in a container.…

Q: A single-stage, single-acting air compressor with runs at 700 r/min. It has a polytropic index of…

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

Q: Air flows at 700 m/s through a long duct in a wind tunnel, where the temperature is 15∘C and the…

A: Given data as per questionAir velocity=700m/sAbsolute pressure=85kpaTemperature in wind tunnel=15…

Q: Consider the given figure with P= 210 N and a = 30 mm. 60 mm 40 A P B The reaction at B= The…

Q: 7) A pendulum which weighs 3.86 lb and has a cord length of 10 in. is released from rest when the…

A: Apply conservation of energy to the system at initial horizontal position and at vertical position…

Q: The 0.75-kg bob of a pendulum is fired from rest at position A by a spring which has a stiffness k =…

A: Given- mass of bob= 0.75 stiffness of spring k= 6 kn/m compressed…

Q: Which statement is correct regarding the structure of polymers? Oa. Degree of crystallinity and…

A: It is asked to provide correct state ment from the options

Q: W= 1 m t = 3 mm 2- A rectangular cross section fin (k-45 W/m °C) with L= 20 mm, thick and T-120 °C…

A: Given Data Thermal conductivity, K=45 W/mKlength of the fin, L= 20mmwidth of the fin, W=1mthe…

Q: Water exits from a large vessel through a smooth pipe, with a length L = 7 m and an internal…

A: Given data:Pipe length, L = 7 mPipe diameter, D = 5 cm = 0.05 mInlet loss coefficient, KL,1 =…

Q: A very thin (negligible mass) wire is connected in series with a battery of 50 V and a resistor of…

A: Given data:Battery voltage (V) = 50 VResistor (R) = 18 ΩWire length (L) = 15 cm = 0.15 mSeparation…

Q: Three steel plates, each 16 mm thick, are joined by two 20-mm diameter rivets as shown in the…

A: Given:16 mm thick, 20-mm diameter P = 50 kNUltimate shear stress for the rivets = 180 MPaTo…

Q: Sketch a simple diagram for the temperature distribution in plane wall for a steady state one…

Q: In fabrication of the high-temperature turbine blades, if you wished to minimize the centrifugal…

A: Turbine blade failure is caused by high-speed rotation and centrifugal forces that the turbine…

Q: A 25-mm-diameter shaft is statically torqued to 230 N. m. It is made of cast 195-T6 aluminum, with a…

A: T= 230 N-m; yield strength in tension =160 MPa ,yield strength in tension =160 MPa ; yield strength…

Q: An unknown polymer sample was found to have the following molecular weight distribution: Molecular…

A: Given:Molecular weight distribution tableDP = 763

Q: Disk A has a mass of 3 kg and is sliding forward on the smooth surface with velocity 8 m/s when it…

Q: Solve using NTU method. Consider a liquid (Cp = 2.2 kJ /kg·K) is cooled at a rate of 12 kg/min from…

Question

A converging nozzle having an exit diameter of 30 mm is
connected to the large tank (Figure 1). The absolute pressure
outside the tank is 102 kPa.
Figure
m
If the temperature of the air in the tank is 20°C and the absolute pressure is 380 kPa, determine the mass flow from the tank.
Express your answer using three significant figures.
5. ΑΣΦ 11 vec
Submit
Request Answer
?
< 1
of 1
1 of 1 >
kg/s
A

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Write the given data wirh suitable variables.

VIEW

Step 2: Find the exit temperature and exit Mach number.

VIEW

Step 3: Determine the mass flow rate.

VIEW

Solution

VIEW

Step by step

Solved in 4 steps with 9 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Nitrogen having a temperature of T₁ = 270 K. and absolute pressure of p₁ = 330 kPa flows into the smooth pipe at M₁ = 0.3. It is heated at 100 kJ/kg-m]. (Figure 1) Figure 4 m 1 of 1 Part A Determine the velocity of the nitrogen when it exits the pipe at section 2. Express your answer to three significant figures and include the appropriate units. V₂ = Submit Part B P2 = Submit μᾶ Value Request Answer Provide Feedback Determine the pressure of the nitrogen when it exits the pipe at section 2. Express your answer to three significant figures and include the appropriate units. HÁ Value Request Answer P Units Units ? *** ? Next >
QI/ the cylinder contains 0.2 kg of saturated water vapor at 1000 kPa. The stops location corresponds to 50% of the initial volume. the steam is cooled until the pressure is reached to 500 kPa. If the piston reaches the stops? and what are the initial and final Seam temperature.
The air in the reservoir has an absolute pressure of 450 kPa and a temperature of 30°C. The throat has a diameter of 50 mm. (Figure 1) Figure 50 mm 1 of 1 Part A Determine the greatest possible mass flow through the nozzle. Express your answer using three significant figures. m = Submit VAΣo↓vec Provide Feedback Request Answer ? kg/s Next >
(1) The inlet velocity Vi is known. Neglect friction losses and determine the manometer reading h in terms of Vi ( the velocity at position 1), H, L , D, d, and the densities of water and mercury. The left hand branch of the manometer is exposed to the atmosphere as is the nozzle exit (position 2). d 2 L PH:0 D Water H PHg Mercury
Nitrogen having a temperature of T1T1 = 290 KK . and absolute pressure of p1p1 = 330 kPakPa flows into the smooth pipe at M1M1 = 0.3. It is heated at 100 kJ/[kg⋅m]kJ/[kg⋅m]. (Figure 1) Figure 1 of 1 Part A Determine the velocity of the nitrogen when it exits the pipe at section 2. Express your answer to three significant figures and include the appropriate units. V2V2 = nothingnothing SubmitRequest Answer Part B Determine the pressure of the nitrogen when it exits the pipe at section 2. Express your answer to three significant figures and include the appropriate units. p2p2 = nothingnothing
What is the final temperature of ammonia (chemical formula NH3) in a rigid tank, if the tank initially contains mNH3 = 28kg of ammonia at a temperature Tinit = 50 °C and an initial pressure of Pinit = 740 kPa, and then half of the ammonia is released, reducing the pressure to 350 kPa?
Determine the gage pressure in the gas chamber. Mass of the floating body m=1,02·103 kg, diameters D=1 m, d=0,6 m, height a=1,4 m. Atmospheric pressure patm-100 kPa, water density p=1020 kg/m³, h=0,5a. Air compression process is isothermal. d Patm a gas D water
Carbon dioxide flows steadily through a varying cross- sectional-area duct such as a nozzle at a mass flow rate of 3 kg/s. The carbon dioxide enters the duct at a pressure of 1400 kPa and 200°C with a low velocity, and it expands in the nozzle to a pressure of 200 kPa. The duct is designed so that the flow can be approximated as isentropic. Determine the following parameters at each location along the duct that corresponds to a pressure drop of 200 kPa: (i) density; (ii) velocity: (iii) flow area; (iv) mach number. You may assume: • Carbon dioxide is an ideal gas with constant specific heats at room temperature; • Flow through the duct is steady, one-dimensional and isentropic. Use c, 0 846 kJ/kgk andk = 1.289 throughout the calculations, which are the constant-pressure specific heat and specific heat ratio values of carbon dioxide at room temperature. The gas constant of carbon dioxide is R = 0.1889 kJ/kg K.
What is the original mass and pressure if the original temperature was 315 K. A 5-m^3 tank contains oxygen at 300 kPa and 300 K after 3 kg of oxygen has been used.
Nitrogen is contained in a 80L tank and the initial pressure andtemperature is 250 kPa and 200 °C, respectively. Note the ideal gasconstant for nitrogen is 0.2968 kJ/kg K Determine: The mass of the gas in kg. Now, if 0.05 kg of gas leaks out of the tank and in the process thetemperature drops to 33 °C. Find the gage pressure of the gasremaining in the tank in kPa. If the atmospheric pressure is 101.325kPa.
Read the question carefully and give me right solution according to the question. If you don't know the solution please leave it. In the piping system assume the air enters the duct at Ma1 = 0.4. The average friction factor for the duct is estimated to be 0.021. If the Mach number at the duct exit is 0.8, and the temperature of cooling the slurry should be >40°C at the duct exit. Determine the length and exit temperature of the duct and if these parameters are suitable for this application.
An airplane is in level flight at low altitude, so that atmospheric pressure and densities are 1 atm and 1 kg/m3, respectively. There is a Pitot tube attached to the airplane, so that air entering the tube stagnates at the rear of the tube. The stagnation pressure is measured to be 1.45 x 105PA. What is the speed of the airplane?