A cylindrical pipe with diameter d = 1.0 m is subject to internal pressure p = 5.0 MPa but it is free to expand along the length, so that only hoop stress o = pd/2t is developed in the wall. a. what is the optimum orientation for the fibers?, and why? b. what is the required wall thickness and material type that yields the minimum thickness?

Q: P2. Design a cylindrical thin-wall composite fuselage for storing compressed natural gas at a…

A:

Q: b. The simply supported beam shown in Figure 9 is fabricated by bonding four separate layers of a…

A: Minimum shear strength: At y = 0, we get the maximum shear stress.

Q: Question 3) The rigid beam CD in the figure is attached to the ceiling with AC and BD rods. The…

A:

Q: I need to calculate the tensile stiffness along the fibre which have a length of 250um  below are…

A: Given: Matrix Stiffness, Em = 6 GPaMatrix Strength = 50 MPaFibre Volume Fraction, vf = 0.41Fibre…

Q: A W 310 X 52 steel beam is subjected to a point load P = 56 kN and a transverse load V = 15kN at B.…

A:

Q: a b A B C D gap (1) L, (2) L, P

A:

Q: How much will a steel wire 2 m long and 1 mm diameter stretch under a 5 kg wt. load? (Y = 2 x 1011…

A:

Q: Example: A bar with a rectangular cross section and a central circular hole in tension F+ W O Id F w…

A:

Q: If the design limit of a 1.5m x 2 m rectangular support beam with a safety factor 5 is 100 x 106…

A: Given: FOS=5Design limit, σd=100×106 N/m2A=1.5m×2mYoung's modulus = 20×109

Q: Problem #3: A circular shaft, fixed to the wall, is loaded as indicated in the figure below. Using…

A: The Rankine's Theory Rankine's theory is a classical theory in engineering mechanics that is used to…

Q: A bar is subjected to fluctuating tensile load from 20KN to 100KN. The material has yield strength…

A:

Q: (b) V brakes Question Four A long retaining wall is braced by wood shores set at an angle of 30° and…

A:

Q: Given: A steel rod (A= 150 mm?) is stretched between two fixed points with a tensile load of 5000 N…

A:

Q: A thin-walled pressure vessel is subjected to internal pressure such that a hoop stress of 100 MPa…

A: There are two stresses present, one in the circumferential direction (3) and one in the longitudinal…

Q: QUESTION 14 A metal matrix composite consists of continuous silicon carbide fibres of radius 25…

A: 14. Given: The volume fraction of silicon carbide fibre, xf = 0.35 The radius of silicon carbide…

Q: In terms Poisson's ratio

A: Given;   In terms of Poisson ratio, μYoungs modulus, EShear modulus, GSo we have to find elastic…

Q: The beam ABCD is loaded with a force, P(N) as shown in Figure 3(a). The T-beam crosssection is…

A:

Q: or the truss shown, Calculate the fol Vertical and Horizontal forces at Po Force is Compression or…

A:

Q: A simply supported beam, 50mm wide by 100mm high and 300 mm long is subjected to a concentrated load…

A:

Q: a uct ang ular Ahaped block with dimensions : L= 127 mm, W's 127 mm, H= 7e. 2 mm is subjected to…

A:

Q: A rectangular polypropylene [E = 6,200 MPa] bar (1) is connected to a rectangular nylon [E = 1,400…

A:

Q: If the design limit of a 1.5m x 2 m rectangular support beam with a safety factor 5 is 100 x 106…

A:

Q: The channel shape cross-section and the rectangular cross-section shown in the Figure Q4 are made of…

A: The solution is mentioned below

Q: A cylindrical pipe with diameter d = 1.0 m is subject to internal pressure p = 5.0 MPa but it is…

A: (a) Write the given data. Internal pressure, P=5 MPaDiameter, d=1 m

Q: 1. At a critical point on the free surface of a loaded beam, the strains are measured in three…

A: Only one question is allowed to solve.

Q: A rectangular plate of composite material is formed with unidirectional fibres orientated at 30…

A:

Q: From the figure shown, Material 1 (brown) is enclosed inside Material 2 (grey). If there would be a…

A: Given:P=357.5 KNd=88.75 mmμ=0.355E=88.56*109 N/m2

Q: Calculate the longitudinal stress at the anchor location for a silicon cantilever with the length L…

A: Given: Length of cantilever→L=150 μm=0.15×10-3 m Height of the cantilever→b=4 μm=0.004×10-3 m Tip…

Q: the figure below shows a vertical nylon filament with a weight suspended from its lower end. The…

A: Write the given values along with the suitable variables.

Q: 3. A 5-m rod having a uniform cross-sectional area of 1000 sq.mm. is secured between two walls 5…

A:

Q: The beam in Figure 1 is subject to a point load F. The length A is 2.23m, The beam is rectangular…

A:

Processing of Polymer Matrix Composites

The polymer matrix composite is described as a composite material that contains some polymer in the form of either fibers or powder. Polymer matrix composites are also known in short as PMC's.