a device that allows hot refrigerant vapor from the compressor discharge line to bypass the condenser and directly enter the liquid receiver when a certain pressure difference occurs between the discharge line and the liquid receiver is a A. condenser pressure regulator B. crankcase pressure regulator C. receiver pressure regulator D. split condenser valye

a device that allows hot refrigerant vapor from the compressor discharge line to bypass the condenser and directly enter the liquid receiver when a certain pressure difference occurs between the discharge line and the liquid receiver is a A. condenser pressure regulator B. crankcase pressure regulator C. receiver pressure regulator D. split condenser valye

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter47: High-pressure, Low-pressure, And Absorption Chilled-water Systems

Section: Chapter Questions

Problem 9RQ: The approach temperature for the evaporator is A. the difference between the suction and head...

See similar textbooks

Similar questions

What advantage does a capillary tube have over a thermostatic expansion valve?
What advantage does a thermostatic expansion valve have over a capillary tube?
The approach temperature for the evaporator is A. the difference between the suction and head pressures converted to temperature. B. the difference between the refrigerant boiling temperature and the suction-line temperature. C. the difference between the refrigerant boiling temperature and the inlet water temperature. D. the difference between the refrigerant boiling temperature and the leaving-water temperature.
Evaporative condenser is used only air as condensing medium to condense the hot vapour refrigerant. * True False
1. A temperature drop in the coolant entering the primary loop can be dangerous because,(a) Reactivity can increase as a result.(b) Pressure in the primary loop will decrease and water can flash to steam.(c) All of the above.(d) None of the above
Given the following information about a condenser system, determine the fan power requirement, Fp:1. Emission stream flow rate (Qe,a) = 2050 acfm2. Condenser system pressure drop (P) = 5 in. H2O3. Condenser system operating hours per year (HRS) = 6000 h/yr
gas refrign 19. A device that opens when condenser pressure rises to a proper level and closes to block the flow of refrigerant from the condenser to the liquid receiver when condenser pressure drops too low is a A. condenser pressure regulator B. crankcase pressure regulator C. receiver pressure regulator D. split condenser valve 10. apor i 11. I tor Dre and erting some re
Problem 3: The high_temperature evaporator (Refrigeration capacity 5 TR) of a multi-evaporator VCR system, working with ammonia, is operating at -6°C and the low temperature evaporator (Refrigeration capacity 10 TR) is operating at -34°C. The condenser pressure is 10.99 bar. The system using individual expansion valves for each evaporator. Assuming saturated conditions at the exit of evaporators and condenser and isentropic compression: a) Find the required power input and COP if a single compressor is used. b) If individual compressors are used for both stage find the power input and COP. c) Compare both cases.
Fraction dryness measures .9 the percent of the liquid refrigerant in the condenser. the percent of the vapour refrigerant at any point in the expansion valve. the enthalpy of the refrigerant at the inlet of the expansion valve. none of these answers. O the amount of the refrigerant in the сycle.
A. Using the steam tables, determine the amount of coolimg water needed by a condenser in kg/sec if wet steam comes into the condenser at P= 610.44mmHG vac and 99.47% moisture, mass flow rate= 7200 + (100/25) kg/hr. Cooling water enters the condenser at 12 deg C and leaves at 21 deg C. Answer: ___ B. Draw the schematic diagram if the condeser and process in the PV and TS diagram. Cp H2O= 4.187 KJ/(kg-K)
Distinguish between Contact condenser and Surface condenser.
The type of condenser in which the steam and cooling water flow from top to bottom and mix is called O a. central flow surface condenser Ob. down flow surface condenser evaporative surface condenser O d. parallel flow jet condenser