1. A floor plan shown has the following space allocations - an office conference room, a small storage area for light materials, and lobby that serves as an exit facility towards the fire exit. Compute the effective live load (in kN/m2 or kPa) that the floor will carry using the Varignon's formula: A Areal (Live Load 1) + Area2(Liveload) + ... so on Total Area of the floor

1. A floor plan shown has the following space allocations - an office conference room, a small storage area for light materials, and lobby that serves as an exit facility towards the fire exit. Compute the effective live load (in kN/m2 or kPa) that the floor will carry using the Varignon's formula: A Areal (Live Load 1) + Area2(Liveload) + ... so on Total Area of the floor

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question: Refer to Figure 1 to find the bulk plane and determine the height of Ironman's House. Consider only two street sides (Silver St. and Gold St.), of which the required bulk plane angles are 45°. What is the maximum height of the Ironman's House that satisfies the required building code? Silver St. 10 ft Figure 1 60 ft Property Ironman's House Flat roof building (40 ft x 30 ft) 10 ft setback-all sides Gold St. 20 ft
1. Calculate slab dead load intensity in kPa (kilo Pascal = kN/m²) in a main floor condo building, given the following parameters: - Allow for 0.3kPa for M&E (i.e. Parkade mechanical and electrical like for example ducts, light fixtures etc..). Minimum allowance for partition walls as per ABC2019 175mm concrete slab 0.2kPa for tiling allowance (including tiles, adhesive, and grout)
PLEASE HELP, Determine the occupant load for the small restaurant. WILL THUMBS UP IF CORRECT.
Determine the quantity of standard concrete blocks (400 x 200 x 200) required in 100 m² of a 200 mm thick wall. Assume 5% waste. 262 pcs "1,213 pcs" O "c. 1,313 pcs" None of the above
A fence with dimensions of 15m long by 20m high including portions below NGL. Determine the number of CHB needed using 200x400mm concrete hollow blocks. Consider 5% wastage
Listen What should you enter for the Total HAWB on the Consolidation Manifest? 2 34 14 20
Find the maxm.capacity.
Define The shape of the loaded area
INCLUDE FIGURE/DIAGRAM A multistory commercial building is to be designed as a flat plate system with floors of uniform thickness having no beams or drop panels. Columns are laid out on a uniform 20 ft spacing in each direction and have a 16 in. square section and a vertical dimension 10 ft from floor to floor. Specified service live load is 100 psf including partition allowance. Using the direct design method, design a typical interior panel, determining the required floor thickness, size and spacing of reinforcing bars, and bar details including cutoff points. To simplify construction, the reinforcement in each direction will be the same; use an average effective depth in the calculations. Use all straight bars. For moderate spans such as this, it has been determined that supplementary shear reinforcement would not be economical, although column capitals may be used if needed. Thus, slab thickness may be based on Eqs. (13.11 a ), (13.11 b ), and (13.11 c ); or column capital…
CHAPTER 2 ASSIGNMENT: Use the NSCP 2010 for the following problem sets using the framing plan shown: SITUATION: The second floor of a library has any area that can be used for stacks. Assume that there will be a steel channel ceiling system (0.10kPa) and asphalt tile on the floors. The floors are 150mm reinforced concrete. Allowance should be provided for mechanical ducts. Determine the: a. floor dead load in kPa b. live load in kPa to be applied to Column C3 C. reduced floor live load in kPa, if any Basic building layout B DO 4 at 12m = 48m d. Also, draw the loading diagrams for an interior beam, an interior girder and an interior column.
H.W No.2: A 12 inch circular pipe is to be installed in a positive projection embankment under an unsurfaced roadway and covered with 3.0 feet of 100 pounds per cubic foot backfill material.. Assume a Type 3 Installation. The wall thickness for a pipe with a B wall is 2-inches per ASTM C76 and a 12 inch thick concrete road pavement of 150 pound per cubic foot unit weight. Select: Reinforced pipe classes required pipe strength in terms of 0.01 inch crack D- load. Highway Live Load B.
CHAPTER 2 ASSIGNMENT: Use the NSCP 2010 for the following problem sets using the framing plan shown: SITUATION: The second floor of a library has any area that can be used for stacks. Assume that there will be a steel channel ceiling system (0.10kPa) and asphalt tile on the floors. The floors are 150mm reinforced concrete. Allowance should be provided for mechanical ducts. Determine the: a. floor dead load in kPa b. live load in kPa to be applied to Column C3 c. reduced floor live load in kPa, if any Basic building layout 4at 12m - 40m d. Also, draw the loading diagrams for an interior beam, an interior girder and an interior column. 3 10m-30m