A) If an accurate value for the notch sensitivity is hard to find, I should consider the fatigue stress factor higher than the stress concentration factor under static loading condition in or False concentration design. True B) If the same design safety factor is used, the reduction of the shaft diameter from 2" (inches) to 1" (inch) would cause the deflection of the shaft increases approximately ( ) times.

A) If an accurate value for the notch sensitivity is hard to find, I should consider the fatigue stress factor higher than the stress concentration factor under static loading condition in or False concentration design. True B) If the same design safety factor is used, the reduction of the shaft diameter from 2" (inches) to 1" (inch) would cause the deflection of the shaft increases approximately ( ) times.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

True or False a) If an accurate value for the notch sensitivity is hard to find, I should consider the fatigue stress concentration factor higher than the stress concentration factor under static loading condition in design. b) It is easier to find the asymptotic value of fatigue strength as the endurance limit on the S-N curve for a brass alloy (Cu70Zn30) than that of endurance limit on the S-N curve for an AISI 1045 steel. a good fatigue design should keep the fatigue design factor of safety at a minimum value of______________
Calculation of Limits using ANSI B4.1 Standard Tables, when one of the design Features Exists. When calculating the limit tolerances for features that mate with purchased parts, the purchased part size must be known. This may be obtained be requesting a drawing from a vendor or, a caliper or micrometer can be used to obtain an accurate size. A shaft diameter of 1.2500" is to be pressed into a part using a FN3 interference (force) fit. Limits of size for the shaft diameter are 1.2500" and 1.2495". Determine the Limits of the hole diameter. Show all work.
WHAT I6 THE NOMINAL RATE OF INTE REST COMPOUNDED CONTINOUSLY FOR IOYRS IF THE COMPOUND AMOUNT FACTOR IS EQUAL TO 1.34986
On the part shown, specify a paralellism tolerance to make the top surface parallel to datum A within a total of .002, and with both the profile and parallelism applied to the part above what is the maximum height of the top surface to datum A? Can the MMC Modifier be applied to the feature tolerance? why or why not?
known. Using simple measurement tools, the following features are measured. A spring is known to be made from music wire, ASTM A228 steel, however no other data are Free length of the spring was 44.45 mm. Outside Diameter was 14.25 mm Wire diameter was 1.4 mm The ends are squared and ground The total number of coils was 10.0 This spring will be used in an application where the normal operating load is to be 62.28 N. (Take 1 inch = 25.4 mm) a) Determine the inside diameter, spring index and Wahl factor. b) Determine the expected stress at this operating load. c) Determine the spring deflection at the normal operating load. d) Determine the operating length, solid length and the spring rate. e) Determine the coil clearance and check the spring against buckling. Datermine the minimum hole diameter for the spring to operate in.
QUESTION 1 TOLERANCE A solid steel shaft with a diameter of 130 mm must be press-fittd in a journal bearing (Figure 1) with an inlet and outet diameters of 130 and 145 mm, respectively. Both solid shaft and journal bearing require rigidity and alignment with an accuracy of the location. Consider a journal bearing hlet diameter as the basic size. Outlet Bearing Inlet Joumal Figure 1 AJournal Bearing 1.1 State the two applicable standards when determining the fits for holes and shafts. Determine the following: 1.2 the tolerance class, ISO code, and the nominal diameter that can be used, 1.3 the tolerance limits for both the solid steel shaft diameter and the journal bearing inlet diameter, and 1.4 the dimensions of both the solid steel shaft diameter and the journal bearing inlet diameter.
QUESTION 1 A suitable factor of safety to apply when selecting the cable for a factory hoist is: 05 O1.2 0.2 O 25 QUESTION 2 A winch drum of diameter 199mm turning at 14rpm lifts a load of 5.5kN. What is the winch output power? Give your answer in W to 1 decimal place without units eg 102.3 NOT 102345239 W QUESTION 3 The figure below shows two proposed designs of drums to solve the same load and line speed lifting arrangement. What is the biggest advantage with design A: A The torque on the drum shaft will be lower O The rope speed will be lower The bending moment in the drum shaft will be lower O The weight of the drum material will be less 刚 B
1) A shaft, mounted in bearings at A and D, holds pulleys at B and C. All forces shown represent belt pulls. The shaft is made from ASTM grade 25 cast iron (Sur-26 kpsi, Suc-97 kpsi). The application requires a safety factor of SF=2.8. What diameter should be used for the shaft? [Remember, cast iron is a brittle material and brittle materials use Modified Mohr Theory] 300 lb 6" D. 50 lb fe 8" D. 27 lb 360 lb D 7" 6°
What is the fatigue-strength reduction factor for a shaft with an annealed sled-runner keyway under torsion if the notch sensitivity factor is 0.72?
500 N 30* A transmission shaft, supporting two pulleys A and B and mounted between two bearings C, and Cz is shown in Fig. Power is transmitted from pulley A to B. The shaft is made of plain carbon steel 45C8 (S = 600 and Sy 380 N/mm?). The pulleys are keyed to the shaft. Determine the shaft diameter using the ASME code if, 3000 1500 N -200- -150- 200 ko = 1.5 and k = 1.0 2000 N 500 N
In case of general procedure in machine design, the first phase is recognition of need or aim. Select one: O True O False Fatigue is a process associated with loading or cyclic The bearing the shaft or the axle and holds it in the correct position. In case of bearing design, the race rotation factor "V" depends upon whether the inner race is rotating or the outer race. Select one: O True O False
Hand written plzz 1) A 6061-T6 aluminium alloy flat, simply supported disk valve of 0.2 m diameter and 10 mm thickness is subject to a water pressure of 0.5 MPa. What is the factor of safety, assuming failure to take place according to the maximum principal stress theory? The yield strength of the material is 241 MPa, E-200 GPa and v-0.3.