Answered: A lift pump was used to collect water…

A lift pump was used to collect water at 60 strokes per minute and 50 liters was collected. The lift pump has a bore of 10 cm and stroke of 15 cm. What is the volumetric efficiency of the lift pump?

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter34: Emission Control Diagnosis And Service

Section: Chapter Questions

Problem 2RQ: What will result from too little EGR flow? And what can cause a reduction in the flow?

See similar textbooks

Related questions

Q: If the beam in Problem 1 is made of W18 X 65, A992 structural steel, Illustrate the state of stress…

A: Given that, Given data, W 18×65θ=30° from horizontal axis, Calculate the reaction at the…

Q: Question #1 (10 pts) Rankine cycle – Consider the ideal cycle shown below and determine the thermal…

Q: An adiabatic compressor receives 1.5 m³/s of air at 30°C and 101 kPa. The discharge pressure is 505…

Q: below to solve the ff: 1. Total acceleration of the end of the crank.(in/s2) 2. Angle in degrees…

Q: What will be the stress induced in a steel bar when it is heated from 15°C to 60°C, all expansion…

Q: A 6 ½ -in. shaft, of AISI C1045 WQT1000, has a pulley keyed to it. Compute the (a) length of square…

Q: 2-33.Find the resultant of the forces shown in Figure P2-33. 15° 20° 5 kN 4 kN 2 kN 30° 3 kN FIGURE…

Q: Air is contained in a piston-cylinder and is compressed in a reversible adiabatic manner from a…

Q: The assembly is the same as in problem 2. It consists D of two rods AC and BD attached to the 100-lb…

Q: A motor is being to used to turn the shaft of a centrifugal pump. Apply the equation shown in the…

A: given; torque(T)=100lbf =11.298Nmrotational speed(N)=850rpmpower(P)=?

Q: By the method of this article, determine the rectangular and polar radii of gyration of the shaded…

Q: 9. A nozzle is designed to expand air from 689 kPaa and 32 °C to 138 kPaa. Assume an isentropic…

Q: The flow through a circular pipe is laminar. Now, the fluid through the pipe is replaced with a more…

A: When fluid flows in a circular pipe at low velocity, then the intermingling of fluid particles was…

Q: Which of the following statements is correct 1. Friction factor is always a constant 2.…

A: To determine which of the given statement is correct

Q: QB3 TWO DIMENTIONAL STRAIN Three strain gauges were arranged in the form of a rectangular rosette…

Q: Friction in pipe cause O 1. reduction in potential energy 2. Reduction in velocity 3. Reduction in…

A: Friction loss in pipe is the Major loss.

Q: Would the volumetric flow rate in a pipe, assuming laminar flow, be more or less if the fluid were…

Q: 4. From the given coplanar force system which consists of two forces and one couple. Replace the…

Q: 5.42 PQ If an automobile tire develops a leak, how does the mass of air and density change inside…

A: Given question: If an automobile tire develops a leak, how does the mass of air and density change…

Q: below, find the ff: 1. Tangential acceleration of the end of the crank.(in/s2) 2. Normal…

Q: 7. Oxygen at 300 kPa, 100°C is in a piston-cylinder arrangement with a volume of 0.1 m?. It is now…

Q: n expands polytropically through a turbine according to the = C. The inlet temperature is 1000 K,…

Q: ermine the magnitudes of all pin reactions for the frame loaded as sh ume F-860 N, a - 695 mm, b -…

Q: View Factor Example #2 Surface 1 is very long 0.3-m x 0.4-m "L" formed from a pair of perpendicular…

A: Given: The area of surface, A1 = 0.3 m x 0.4 m The diameter of surface 2, d = 0.1 m

Q: 9. The submerged, curve surface AB in figure below is one quarter of a circle of radius 4 ft. The…

Q: Air at atmospheric pressure and a temperature of 25°C is in parallel flow at a velocity of 5 m/s…

Q: 5. Submit the required force P. a = 2 m/s? P 50 N 300 N 500 N f= 0.2

Q: The shear stresses in the fluid flow are caused by O Pressure O Temperature O Friction O Volume

A: Option C). friction Shear stress is due to friction between two adjacent layers of the fluid when…

Q: 10. Ice accumulation on an evaporator can be quickly pressure to open and close a larger valve is 9.…

A: Given questions are related to refrigeration and fluid flow control:…

Q: The maximum bending stress of a hollow shaft is equivalent to 80N/mm2, while the maximum shear…

Q: 6% of the stroke. State 1 is defined by 14psia and 140°F. For the hot-air standard with k=1.34 and…

Q: Determine the force in member BE of the loaded truss. The force is positive if in tension, negative…

Q: Calculate the polar moment of inertia of the shaded area about point O. y 33 mm 19 mm | Answer:I, =…

Q: 7. One pound of an ideal gas undergoes an isentropic process from 95.3 psig and a volume of 0.6 fA°…

Q: Pressure drop between two sections of a unifrom pipe carrying water is 9.81 kPa. Then the head loss…

Q: The rectangular area shown in part a of the figure is split into three equal areas which are then…

A: According to the details provided in the question, we need to calculate the percent increase in the…

Q: A closed cylindrical tank that is 2m in diameter and has a height of 8m contains 6m deep of oil with…

Q: Two cables of different materials have an initial length of 1 m and a cross-sectional area of 2x10…

Q: When the angular velocity of a 4ft. Diameter pulley is 3 rad/sec., the total acceleration of a point…

Q: I- If a rigid body undergoing planar motion, it has at most II- Second moment of force (F.r) is…

A: To find :- Fill in the blanks

Q: Example 6: Replace the force and couple system acting on the member shown by an equivalent resultant…

Q: Determine the coordinates of the centroid of the shaded area. y

Q: 5. Air is compressed polytropically in a cylinder according to pV² = C. The wor required is 180 kJ.…

Q: For what value Mof the clockwise couple will the horizontal component A, of the pin reaction at A be…

A: find the value of moment M when horizontal reaction at A is zero. find the value of horizontal…

Q: The wind chill, which is experienced on a cold, windy day, is related to increased heat transfer…

A: Given, Thickness of fatty tissue = t = 3 mm = 0.003 m Temperature of internal surface of fatty…

Q: The fluid flow through a pipeline can be assumed as Unsteady flow Uniform flow…

A: Steady flow is the correct answer.

Q: Determine the force in member BF. The force is positive if in tension, negative if in compression.…

Q: Which of the following statement is correct O 1. Reynolds number depends on the viscosity of fluid O…

Q: A solid steel shaft, circular in cross section, has a change in diameter from 135 mm to 90 mm with a…

Q: A jet of water with a velocity of 30 m/s impinges on a series of canes moving at 12 m/s at 30 to the…

Concept explainers

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.

Question

A lift pump was used to collect water at 60 strokes per minute and 50 liters was collected. The lift pump has a bore of 10 cm and stroke of 15 cm. What is the volumetric efficiency of the lift pump?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Answer:

VIEW

Explanation:

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Pump at its best efficiency point(BEP) has a capacity of 12500 gpm while developing a head of 60ft at a rotative speed of 1450rpm. What is the specific speed of the pump? ANSWER: 7520rpm
a pump operating at 1750 rpm delivering 600 gpm against total head of 200 tt. changes in the piping system have increase the total head of 450 tt. At what RPM should the pump be operated to achieve thus new head at the same efficiency?
The 11-in Bell and Gossett pump is tobe scaled up to provide, at best efficiency, ahead of 250 ftand a flow rate of 3000 gal/min. Find the appropriate(a) impeller diameter; (b) speed in r/min; and (c) horsepowerrequired.
The suction diameter of 60mm reads 2psi vaccum and 50mm diameter discharge with 250kpag. The suction water level is 5m above water pump center line and discharge water level is 25m above the pump center line. The total head loss at suction and discharge is 2m. If discharge is 0.01m3/s, find the horsepower needed to pump the water for 80% pump efficiency. ANSWER: 8.15 hp
A pump delivers 1000 gallons per minute of water at a head of 100ft. Find the water power needed. Answer: 25.28 hp
A single acting reciprocating pump having cylinder diameter of 150 mm and stroke300 mm is used to raise water through a total height of 30m. Find the power required todrive the pump, if the crank rotates at 60 rpm
times A cenrifugal pump having outer diameter equal two the inner diameter and running at 1200rpm works agaist a total head of 32m. The velocity of flow through the impeller is constant and equal to 3m/s. The vanes are set back at an anhgle of 30°at the outlet. If the outer diameter of the impeller is 600mm and width at outlet is 50mm, determine: a- Vane angle at inlet. b- Work done per second by impeller. c- Manometric efficiency.
A pump running at 600 rpm and delivers 22.7 m³/min of water against a total head of 19.5 m. The same pump is now required to deliver water at 30.5 m total head. At what speed should the pump be driven and what would be the new flow rate and power if the efficiency is 70%.
A centrifugal pump works against 10 m at 1000 rpm. The varies are curved back at an angle of 30° to the tangent at the outer periphery. The impeller diameter is 30 cm and has width 5 cm at outlet. Determine the discharge if Manometric efficiency is 95%, also determine power required to operate the pump if the overall efficiency is 65%.
a pumping station working with a pump head of 25m. the output power of the motor for that pump is 16kw. identify the pump efficiency if the sewarge discharge velocity is 0.27 m/s and the pipe diameter is 250 mm
A hydraulic vane pump running at 1800 rpm develops 2 L/s flow at 750 kPa. Volumetric efficiency is .85 and overall efficiency is 0.8. Determine the Theoretical Torque required, TT (N-m). (Hint: first calculate the mechanical efficiency and theoretical flow rate. Convert rpm to rad/s). O 9.41 N-m 8.85 N-m 9.35 N-m 9.62 N-m 8.80 N-m
A centrifugal pump having an impeller of diameter 500 mm delivers 140 litres of water per sccond. The velocity of flow is 1 m/s and the vanes are curved back at outlet at 30° to the wheel tangent. If the impeller speed is 400 r.p.m., find the power to drive the pump. (Ans. 12-9 kW) 3.