A pine wood specimen was prepared with actual dimensions of 50 mm × 50 mm x 250 mm and grain parallel to its length. The deformation was meas- ured over a gauge length of 200 mm. The specimen was subjected to compres- sion parallel to the grain to failure. The load-deformation results are as shown in Table P10.25. TABLE P10.25 Load (Kn) Deformation (mm) 8.9 0.457 17.8 0.597 26.7 0.724 35.6 0.838 44.5 0.965 53.4 1.118 62.3 1.270 71.2 1.422 80.1 1.588 89.0 1.765 97.9 1.956 106.8 2.159 111.3 2.311 a. Using a computer spreadsheet program, plot the stress-strain relationship. b. Calculate the modulus of elasticity. c. What is the failure stress?

A pine wood specimen was prepared with actual dimensions of 50 mm × 50 mm x 250 mm and grain parallel to its length. The deformation was meas- ured over a gauge length of 200 mm. The specimen was subjected to compres- sion parallel to the grain to failure. The load-deformation results are as shown in Table P10.25. TABLE P10.25 Load (Kn) Deformation (mm) 8.9 0.457 17.8 0.597 26.7 0.724 35.6 0.838 44.5 0.965 53.4 1.118 62.3 1.270 71.2 1.422 80.1 1.588 89.0 1.765 97.9 1.956 106.8 2.159 111.3 2.311 a. Using a computer spreadsheet program, plot the stress-strain relationship. b. Calculate the modulus of elasticity. c. What is the failure stress?

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.1P

See similar textbooks

Similar questions

According to Figure 5-20, is ii possible to completely separate one of the four materials from the other three? Explain your answer.
A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
A pine wood specimen was prepared with actual dimensions of 50 mmx50 mm x 250 mm and grain parallel to its length. The deformation was measured over a gauge length of 200 mm. The specimen was subjected to compression parallel to the grain failure. The load- deformation results are shown in table below: Load (kN) Deformation (mm) 8.9 0.457 17.8 0.597 26.7 0.724 34.5 0.838 43 0.965 52.9 1.118 62.01 1.27 71.03 1.422 80.1 1.588 89 1.765 99.6 1.956 108 2.159 111.3 2.311 112 2.456 a. Using a computer spreadsheet program, plot the stress-strain relationship. b. Calculate the modulus of elasticity. С. What is the failure stress?
HW:No.2 (The deadline for submitting your homework on Sandety (404.2014). Three steel bars with a diameter of 25 mm and carbon contents of 0.2, 0.5, and 0.8%, respectively. The specimens were subjected to tension until rupture. The load versus deformation results were as shown in Table below If the gauge length is 50 mm, determine the following: a. The tensile stresses and strains for each specimen at each load increase. b. Plot stresses versus strains for all specimens on one graph. c. The modulus of elasticity for each specimen. d. ultimate strength for each specimen. e. The strain at rupture for each specimen. f. the percentage of the total elongation. 3. Specimen No. Carbon Content (%) 1. 2 0.2 0.5 0.8 Deformation (mm) Load (kN) 0.00 0. 0.07 133 133 133 0.10 137 191 191 0.15 • 142 196 285 0.50 147 201 324 1.00 140 199 383 2.50 155 236 447 5.00 196 295 491 (Rupture) 7.50 226 336 10.00 241 341 12.50 218 304 (Rupture) 13.75 196 (Rupture)
412/2021. HW:No.2 (The deadline for submitting your homework on Snday 042814). Three steel bars with a diameter of 25 mm and carbon contents of 0.2, 0.5, and 0.8%, respectively. The specimens were subjected to tension until rupture. The load versus deformation results were as shown in Table below If the gauge length is 50 mm, determine the following: a. The tensile stresses and strains for each specimen at each load increase. b. Plot stresses versus strains for all specimens on one graph. c. The modulus of elasticity for each specimen. d. ultimate strength for each specimen. e. The strain at rupture for each specimen. f. the percentage of the total elongation. 3 Specimen No. Carbon Content (%) 1 2 0.2 0.5 0.8 Deformation (mm) Load (kN) 0.00 0. 0. 0. 0.07 133 133 133 0.10 137 191 191 0.15 • 142 196 285 0.50 147 201 324 1.00 140 199 383 2.50 155 236 447 5.00 196 295 491 (Rupture) 7.50 226 336 10.00 241 341 12.50 218 304 (Rupture) 13.75 196 (Rupture) Stress Strain Curve and Explanation…
Please present FBD/s A tensile test is performed on a brass specimen 10mm in diameter using a gage lenght of 50mm. When the tensile load P reaches a valule of 20kN, the distance between the gage marks has increased by 0.122mm. What is the modulus of elasticitiy of the brass?
The grains of wood in the board make an angle of 20° with the horizontal as shown. The board is subjected to an axial load of P = 250 N . (Figure 1) Part A Determine the normal stress that acts perpendicular to the grains. Express your answer to three significant figures and include the appropriate units. µA Value Units Figure 1 of 1 Submit Request Answer Part B 300 mm Determine the shear stress that acts parallel to the grains. 60 mm Express your answer to three significant figures and include the appropriate units. 20° 25 mm HẢ ? Value Units P Pearson
The grains of wood in the board make an angle of 20° with the horizontal as shown. The board is subjected to an axial load of P = 300 N. (Figure 1) Part A Determine the normal stress that acts perpendicular to the grains. Express your answer to three significant figures and include the appropriate units. µA Value Units Submit Request Answer Figure < 1 of 1 Part B Determine the shear stress that acts parallel to the grains. Express your answer to three significant figures and include the appropriate units. HA -300 mm 160 mm Ta'y = Value Units 20° 25 mm1 Submit Request Answer
6) Two pieces of wood (of cross-section 5 cm x 5 cm) are glued together. The length of the overlapping region is 15 cm. a) Calculate the shear stress experienced by the specimen under an applied tensile force F of 2kN. b) If the glued faces can resist a maximum shear stress of 1 MPa, how much load can this specimen support? 5 cm F 15 cm
The breaking strength of a 15.0 mm diameter bar was 540 MPa and the cross-sectional diameter after rupture was measured as 12.3 mm. Calculate the ductility in percent shrinkage and the actual stress at break.
An aluminum alloy cylinder with a diameter of 3 inches and a height of 6 inches issubjected to a compressive load of 50,000 pounds. Assume that the material is within theelastic region and a modulus of elasticity of 11 x 106 psi.a. What will be the lateral strain if Poisson’s ratio is 0.33?b. What will be the diameter after load application?c. What will be the height after load application?
In a standard tensile test, an aluminum rod of 20-mm diameter is subjected to a tension force of P- 30 kN. Knowing that E- 70 GPa, and the change in diameter of the rod- 0.00955 mm, determine the poissons' ratio v. 20n diateter gage length-150 0.33 O 0.6 0.29 O 0.35