A point within an embankment slope has a vertical normal stress (O) of 100 kPa, a horizontal normal stress (Ox) of 60 kPa, and a horizontal shear stress (Txy) of 20 kPa. (a) Determine the major and minor principal stresses. (b) Determine the orientation of the major principal stress (in degrees from vertical, clockwise, or counterclockwise. (c) Draw the Mohr Circle and schematic of the element stress state.

A point within an embankment slope has a vertical normal stress (O) of 100 kPa, a horizontal normal stress (Ox) of 60 kPa, and a horizontal shear stress (Txy) of 20 kPa. (a) Determine the major and minor principal stresses. (b) Determine the orientation of the major principal stress (in degrees from vertical, clockwise, or counterclockwise. (c) Draw the Mohr Circle and schematic of the element stress state.

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter16: Lateral Earth Pressure

Section: Chapter Questions

Problem 16.4P: In Problem 16.3, if there was a surcharge of 20 kN/m2 at the ground level, what would be the total...

See similar textbooks

Similar questions

The soil profile at a site is shown Figure P16.3. Find the total horizontal normal stresses at A and B, assuming at-rest conditions.
Determine the shear stress at points A, B, C andD for the following section. Also determine the maximum shear stress, then plot the shear stress distribution. Given: V = 10 kN.
A point in the ground has a total vertical (normal) stress (v) of 200 kPa, a total horizontal (normal) stress (x) of 120kPa, a horizontal shear stress (xy) of 0 kPa, and a pore water pressure (uo) of 40 kPa.(a) Determine the shear and effective normal stresses that act on a plane oriented 30 degrees clockwise fromhorizontal. Sketch the plane and draw the stresses acting on it; make sure you have the correct signconvention.(b) Determine the shear and effective normal stresses that act on a plane oriented 30 degrees counterclockwisefrom horizontal. Sketch the plane and draw the stresses acting on it; make sure you have the correct signconvention.(c) Determine the maximum shear stress and the orientation of the planes on which it acts
Find the vertical stress increment at this point of interest using Boussinesq analysis.
Q2: For the soil element shown in the figure. Draw Mohr circle, locate OP (origin point), then find the stresses inclined at: 1- 75° from the horizontal plane. 2- With the horizontal plane.
A level ground surface exists in an area where soil in the underlying stratum has a wet unit weight of 19 kN/m3. The vertical pressure at any depth represents the major principal stress. The vertical pressure (stress) is the product of the soil unit weight and depth. The lateral pressure at a corresponding depth is 0.45 times the vertical pressure and represents the minor principal stress. (a) Determine the principal stresses acting at a depth 4 m below the surface, and draw the Mohr’s circle for the condition. (b) What is the maximum shear stress acting at this depth?
A circular area having a radius of 3 m carries a uniformly distributed of 90 kPa is applied to the ground. Compute the total vertical stress in kN/m^2 increment due to this unifrom load if the unit weight of soil is 18.40 kN/m^3 at point 6 m below the edge of the circular area. a. 18.62 b. 137.66 c. 115.17 d. 129.02
Determine the maximum average shear stress developed in 30mm diamter pin
An electric power transmission pole is 12 m above ground level and embedded 2 m into the ground. The butt diameter is 450 mm and the tip diameter (the top of the pole) is 320 mm. The weight of the pole, cross arms, and wires is 33 kN. Assuming the pole transmits the load as a point load, find the change in vertical stress in kPa at 2 m depth.
A solid circular pole is subjected to linearly varying distributed force with maximum intensity o at the base and an axial compressive load P at the top (see figure). Find the required diameter d of the pole if the maximum allowable normal stress is 150 MPa. Let go = 6.5 kN/m, P = 70 kN, and L = 3 m.
A strip load of q =53 kN/m^3 is applied over a width B =11m. Determine the increase in vertical stress in kPa at point A located z = 4.6 m below the surface. x = 8.2m
Find the expressions to calculate the maximum normal and shear stresses for a circular profile: d (diameter)= 0.30 m