A pumped fluid distribution system is being designed to deliver 400 gal/min of water to a cooling system in a power generation plant. Use the figure below to make an initial selection of Schedule 40 pipe sizes for the suction and discharge lines for the system. Also, solve for the actual average velocity of flow for each pipe. DN (mm) NPS (in) 250 10 200 150 - 125 Suction lines 100 90 80 - 65 50 Discharge lines 40 E 32 14 25 20 34 15 15 20 30 40 200 400 600 800 2000 4000 6000 8000 10000 60 10 80 100 1000 Volume Flow Rate, Q (gal/min) 8 10 15 +++ 6 20 25 30 40 60 80 100 150 200 300 400 S00600 800 1000 1200 2000 +++++ ++ ++++ ++++++ Volume Flow Rate, Q (m/h)

A pumped fluid distribution system is being designed to deliver 400 gal/min of water to a cooling system in a power generation plant. Use the figure below to make an initial selection of Schedule 40 pipe sizes for the suction and discharge lines for the system. Also, solve for the actual average velocity of flow for each pipe. DN (mm) NPS (in) 250 10 200 150 - 125 Suction lines 100 90 80 - 65 50 Discharge lines 40 E 32 14 25 20 34 15 15 20 30 40 200 400 600 800 2000 4000 6000 8000 10000 60 10 80 100 1000 Volume Flow Rate, Q (gal/min) 8 10 15 +++ 6 20 25 30 40 60 80 100 150 200 300 400 S00600 800 1000 1200 2000 +++++ ++ ++++ ++++++ Volume Flow Rate, Q (m/h)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 5: If a pump with the pump curve shown below is attached to a pipeline where the volumetric flow rate is Q = 30 L/s please determine the head that this pump will add to the flow, as well as the approximate efficiency of the pump, for each of the following RPMs: 3250 rpm, 3850 rpm, and 4350 rpm. 70 NPSH required 4350 rpm 60 43% 43% Pump Head (m) 40 30 20 10 10 4350 rpm 20 40% 3250 rpm 30 Flow (L/s) 4350 rpm 4050 rpm 3850 rpm 3550 rpm 3250 rpm 40 4050 rpm 3850 rpm 3550 rpm 50 420 69 46 23 NPSH (m) Horsepower input
The system shown in the Figure for Question is designed to pump water at 40 L/s from reservoir Ato B. The pump is indicated with a P on the diagram. The pipe properties are given in the Table forQuestion. Determine the following for the system: The required working point of the pump and the flow regimes in the suction and delivery pipes.
Q3. Compute volumetric flow rates in each pipe for the given data: Pipe Li (m) Di (cm) Ei (mm) 800 8 0.25 1200 12 0.20 3 600 16 0.28 190m 140m 110m Datumn
A discharge of 600 liters/sec flows through a pipe having a diameter of 400 mm., length of 40 m. long. Compute the head loss of the pipeline using Mannings Equation with n = 0.013. Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: m Decimal Places required in the final answer: 3
In the pipe systems (a), (b), and (c) in the Figure, find the flow and velocity in each pipe and the pressure at points A. Assume all nodes are at identical elevations. m/min 20 m/min 20 m /min P- 1000 kP Sm/min 1500 m 1000 m 455 mm 405 mm 1000 m 405 mm 800 m 255 mm 300 m305 mm 300 m 205 men 1100 m 305 mm 1000 m 305 mm A500 m 205 mm 10 m/min 5m/min 10m3/min 5 m/min 15 m /min 5m/min Elev 300 m 405 mm 2000 m 150 2000 m Elev 250 m 5m/min 10 im/min 6 m/min 205 mm 205 mm 2000 m A 2000 m le) 000
The Reynolds number for the current in a pipe is 10°. If the relative roughness is 2.103, using the Moody diagram find the roughness coefficient (f)? 1 .09 08 07 104 B B Laminar Critical Transition Flow Regional Zone 015 01 009 .008 Laminer Akiş !=64/N 0,032 0,024 0,028 0,034 10 Colebrook Equivariances 2.0 13.7 M The n and Turbulent flow Full Turbulence, Rough Pipes Smooth Pipes 2 3 4 5 8 10 2 4 6 8 10 2 3456 10 Full Smokebulansa The Transit Line 2 3456 10 1x10 568 10 TBD
Fluid Flow in Pipes 2. The flow from pipelines A to F is 300 lit/s. Using a friction factor of 0.015 for all pipelines and with the properties listed below, compute a. the discharge at B b. the discharge at E c. the discharge at D d. headloss from 1 to 5 Pipelines A TEOREY B C D F Length (m) 350 300 320 1100 550 650 Diameter (cm) 40 25 25 30 20 45
The graph shown provides the pump characteristics (performance) curves. There are two pumps in the system. Which statement is totally correct? H Curve 1 Pump 1 Pump 2- Curve 2 Q Curve 1 represents pump in series and curve 2 represents pump in parallel Curve 1 represents pump in parallel and curve 2 represents pump in series O System operating head and discharge can be determined from the intersection point of curves 1 and 2
A pipe system has a flow of 4.6 cfs. Section 1 has a diameter of 12” and Section 2 has a diameter of 10”. What is the velocity at each section?
QUESTION 14 For the pipe network shown in the figure below, what is the flow rate in pipe AC? 5.1 cfs K = 15 B K= 20 A O . 400 GPM O b. 800 GPM Oc 1,200 GPM O d.1,500 GPM K = 10
Oil (SG=0.80) flows through aventuri meter as shown,a. Calculate the flowrate.b. Calculate thereading ‘‘h’’ shownby the differentialmanometer fittedto the pipelinewhich is filled with mercury of specificgravity 13.6.c. How will the flow rate change if the liquidflowing through the pipeline is replacedwith water.
The Answer maps the head required to produce flow in a given system. The Answer describes the relationship between flowrate and total head for the actual pump. ⠀⠀system curve pump performance curve