A rapid-mixing basin for coagulation is to be designed for a water treatment plant.The design flow rate for the basin is 3800 m³/d. The basin will be cylindrical with fourvertical baffles and a side water depth equal to the diameter. The velocity gradient anddetention time will be 1000 s' and 5 s, respectively. Assume the water temperature is 10°C.2.(a) Calculate the basin dimensions in increments of 0.01 m.(b) A radial turbine impeller with a power number of 5.7 will be used to provide mixing,and the following impeller diameters are available (in m): 0.3, 0.4, 0.6. Determine theimpeller diameter to be used, the required rotational speed of the impeller (rpm), and themotor power needed (in W) to turn the impeller.

ANSWER: a) Calculate the total volume: Here, is the design flow rate and is the detention…

A rapid-mixing basin for coagulation is to be designed for a water treatment plant. The design flow rate for the basin is 3800 m³/d. The basin will be cylindrical with four vertical baffles and a side water depth equal to the diameter. The velocity gradient and detention time will be 1000 s' and 5 s, respectively. Assume the water temperature is 10°C. (a) Calculate the basin dimensions in increments of 0.01 m. (b) A radial turbine impeller with a power number of 5.7 will be used to provide mixing, and the following impeller diameters are available (in m): 0.3, 0.4, 0.6. Determine the impeller diameter to be used, the required rotational speed of the impeller (rpm), and the motor power needed (in W) to turn the impeller.

A rapid-mixing basin for coagulation is to be designed for a water treatment plant. The design flow rate for the basin is 3800 m³/d. The basin will be cylindrical with four vertical baffles and a side water depth equal to the diameter. The velocity gradient and detention time will be 1000 s' and 5 s, respectively. Assume the water temperature is 10°C. (a) Calculate the basin dimensions in increments of 0.01 m. (b) A radial turbine impeller with a power number of 5.7 will be used to provide mixing, and the following impeller diameters are available (in m): 0.3, 0.4, 0.6. Determine the impeller diameter to be used, the required rotational speed of the impeller (rpm), and the motor power needed (in W) to turn the impeller.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A well is installed in a unconfined aquifer. Determine the drawdown (ft) at the well if: the radius of influence = 500 ft. The thickness of unconfined aquifer = 95 ft The well diameter =9 in Pump rate =250 gal/min. Hydraulic conductivity = 0.001 ft/sec. 44 7 O 33 11 25
: Water flows over a smooth submerged object in a channel of width 1.2 m. The water depth upstream of the object is 2.2 m and the water depth downstream is 0.5 m. i) Use the Bernoulli and Continuity equations to calculate the discharge within the channel, and sketch the energy grade line and hydraulic grade line for this problem. ii) The measured discharge in the channel is 2.4 m³/s. Calculate the discharge coefficient, and describe what this physically represents. iii) A pitot tube (or stagnation tube) is placed in the downstream part of the channel, where the water depth is 0.5 m. Calculate the height to which water will rise within this pitot tube (above the depth of water in the channel).
A confined aquifer has a of recharge. K for the aquifer is 60 m/day, and n is 0.3. The piezometric head in two wells 1500 m apart is 70m and 60m respectively, from a common datum. The average thickness of the aquifer is 35m. Calculate the following. a. Volume discharged in 2 days in m3 Blank 1 b. Seepage velocity (cm/s) Blank 2
Problem 1. Consider a drainage system that consists of horizontal drains located at an elevation ho above the base of an unconfined aquifer of thickness b 10 m (see Figure 1). The recharge rate is r = 100 mm/yr, and the hydraulic conductivity of the aquifer is K = 1 m/d. The design condition of the drainage system is to avoid ponding at the ground surface. You can ignore the vadose zone for this problem. 1. Obtain the relation between the half-distance between drains, L, and the elevation of the drains, ho. Plot this function over the range of feasible lengths. 2. The cost of each individual drain can be split as the cost of the material (fixed) and the cost of installation (which is assumed to be proportional to the depth b – ho). If the fixed cost is $500 and the installation cost is $100 per meter of aquifer length per meter of depth, can you build a drainage system for less than $1 per meter of aquifer length? If so, what depth ho and spacing 2L would you choose? K= 1 m/day 2L = r…
A well is installed in a confined aquifer. Determine the steady-state drawdown (ft) at the well. Well diameter =12 in The transmissivity = 4000 gpd/ft. %3D The pumping rate = 40 gpm. The radius of influence =1000 ft, 11.7 0.73 22.6 6.8 17.4 30
Estimate the transmissivity of confined - aquifer in steady state flow if you know the drawdown is 3 m in piezometer well while 5 m in pumping well. The distance from pumping well to piezometer well is 30 m and radius of pumping well is 2 m. The pumping rate is (5 x 102 m3/d)
A well is installed in a confined aquifer. Determine the steady-state drawdown (ft) at the well. Well diameter =12 in The transmissivity = 4000 gpd/It. The pumping rate = 40 gpm. The radius of influence =1000 ft, 11.7 0.73 22.6 6.8 17.4 30
Question 2 Refer to Figure 2 below. If the water surface elevation in reservoir B is 110 m, what must be the water surface elevation in reservoir A if a flow of 0.06 m³/s is to occur in the cast-iron pipe (ks = 0.26 mm)? The kinematic viscosity of water at 10°C = 1.3x10-6 m²/s. Ignore all minor headlosses. Elevation = ? Water T= 10°C Elevation = 110 m B L= 150 m D = 15 cm Cast-iron pipe L=100 m, D = 20 cm, cast-iron pipe Figure 2
PROBLEM 2 A well is constructed to pump water from a confined aquifer. Two observation wells are constructed at distances of 100 m and 1000 m respectively. Water is pump from the pumping well at a rate of 0.2m3/min. At steady state, the draw down is observed as 2 m and 8 m respectively in the farthest and the nearest observation wells. Diameter of the test well is 1m. a. Determine the hydraulic conductivity in cm/s if the thickness of the aquifer is 20 m. b. Determine the drawdown in the test well.
Need help with C. 8. An aquifer has a hydraulic conductivity of 12 ft/d and an effective porosity of 17% and is under a hydraulic gradient of 0.0055. (A) Compute the specific discharge. (B) Compute the average linear velocity. (C) The water temperature is 14°C and the mean pore diameter is 0.33 mm. Is it permissible to use Darcy's law under these circumstances? What is the reason for your answer?
The flow through the aquifer can also be calculated from the equation dh (2.8) Q = -T dx level is
12 Determine the quantity of seepage under the dam cross section shown in m3/s/m if the soil has hydraulic conductivity, k=0.0001 meter cube per second. Note the numbers in the figure from left to right are:2.0m, 1.8m, 2.4m and 8.0 m, respectively. 2.00m 8.00 m 1.80 m Datum 12.40m 777 Enter your answer