A state of stress at a point is the result of two separate actions; one produces the pure shear of 35 MPa shown in figure A and the other produces the pure shear of 30 MPa shown in figure B. 35 MPa X Figure A 35 MPa Which of the following most nearly gives the principal planes for the combined state of stress? Figure B 30 MPa 30 MPa

A state of stress at a point is the result of two separate actions; one produces the pure shear of 35 MPa shown in figure A and the other produces the pure shear of 30 MPa shown in figure B. 35 MPa X Figure A 35 MPa Which of the following most nearly gives the principal planes for the combined state of stress? Figure B 30 MPa 30 MPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The state of stress at a point is the result of two loadings as shown in figure. When acting alone, the first loading produces the 3 MPa pure shear with respect of xy-axis. The second loading alone results in the 4 MPa pure shear with respect to the x'y-axis. The angle between the two sets of axis is 30° as shown. If the two loadings act simultaneously then resultant (absolute) shear stress at that point with respect to x-y axis is MPa (in integer). 3 MPa st 1 loading 2 loading 4 MPa α = 30° x'
The stresses acting on element A on the web of a train rail (see part (a) of the figure) are found to be 50 MPa tension in the horizontal direction and 140 MPa compression in the vertical direction (see part (b) of the figure). 140 MPa B 50 MPa A A Side View Cross 57 MPa Section (a) (b) Also, shear stresses of magnitude 57 MPa act in the directions shown. Determine the stresses (in MPa) acting on an element oriented at a counterclockwise angle of 52° from the horizontal. (Use the sign convention for stresses acting on inclined sections. Round your answer for o,1 to at least one decimal place.) Ov1 = MPa MPa Oyi MPа Tx1y1 Show these stresses on a sketch of an element oriented at this angle. (Submit a file with a maximum size of 1 MB. Your submission will be graded by your instructor after the due date based on its accuracy. Your grade may change.) Choose File No file chosen
An element in plane stress on the fuselage ofan airplane (figure part a) is subjected to compressivestresses with a magnitude of 42 MPa in the horizontaldirection and tensile stresses with a magnitude of9.5 MPa in the vertical direction (see figure part b).Also, shear stresses with a magnitude of 15.5 MPa actin the directions shown.Determine the stresses acting on an element orientedat a clockwise angle of 40° from the horizontal.Show these stresses on a sketch of an element orientedat this angle.
Q36 onlys Ratio of stress in part A and B
2. Determine the shearing stress in each of the four walls of a portion of a structural aluminum tubing when it is subjected to a torque of 3 kN-m assuming a uniform wall thickness of 4mm. A ( 51 ) mm В 100 mm 100 mm C D ( 51 ) mm
A thin triangular plate ABC is fixed on side AB. The plate is strained such that all straight lines in the plate remain straight after deformation and that apex C is displaced to point C'as shown. Compute the following: a) the normal strains ex, ey and the shearing strain yxy at point C based on small deformation theory b) the normal strain at point A in the direction of AC based on small deformation theory c) the normal strains ex, ey and the shearing strain yxy at point C based on large deformation theory A 30° -200 mm. 3mm C" 1 I 1 1 60° 4mm
Q.2) A rigid bar ACD is supported by two circular steel (E= 30x10° psi) rods AB & DE and a pin support at C. Bar ACD was horizontal prior to the application of load P. The tensile strain measured in rod AB after the application of the load is ɛ1= 0.003. Determine the rotation 0 of the bar ACD and the normal strain in rod DE. Also calculate the value of load P for these deformations. The diameters of rod AB and DE are 1.5 in. and 2 in, respectively. P - 4 ft 4 ft- 6 ft A Rigid (2) 6 ft 8 ft (1) E В
4.3. At a point in a structural member, yielding occurred under a state of stress given by: 40 40 50 -60 MPa -60 Determine the uni-axial tensile yield strength of the material according to (a) maximum shearing stress theory, and (b) Octahedral shearing stress theory. 4.5. Determine the width t of the cantilever of height 2t and length 0.25 m subjected to a 450 N concentrated force at its free end. Apply the maximum energy of distortion theory. The tensile and compressive strengths of the material are both 280 MPa. 4.6. Determine the required diameter of a steel transmission shaft 10 m in length and of yield strength 350 MPa. In order to resist a torque of up to 500 N.m. The shaft is supported by frictionless bearings at its ends. Design the shaft according to the maximum shear stress theory, selecting a factor of safety of 1.5, (a) neglecting the shaft weight, and (b) including the effect of shaft weight. Use y = 77 kN/m as the weight per unit volume of steel. 190 MPa 30 MPa 40 MPa…
Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. If o - 19 MPa in the direction shown, determine the principal stresses at the point. 10 MPa 26 MPa O 29.24 MPa and -8.49 MPa O 40.89 MPa and -11.89 MPa O 38.28 MPa and -13.02 MPa O 26.15 MPa and -16.23 MPa O 48.08 MPa and -9.80 MPa
The stresses acting on element B (see figure part a) on the web of a wide-flange beam are found to be o = 11,000 psi in compression in the horizontal direction and oy = 2,600 psi in compression in the vertical direction (see figure part b). Also, shear stresses of magnitude Tzy = 3,200 psi, act in the directions shown. B Side Cross View Section (b) (а) Determine the stresses acting on an element oriented at a counterclockwise angle of 45" from the horizontal. Round your answers to one decimal place. psi psi psi
1. As seen in Fig. 1, a beam has two 1400 N. m loads applied to both of its ends. The beam is made of steel and, as can be seen, has a rectangular cross section. Find the maximum bending stress in the beam and show how it changes as the depth of the beam increases. 1400 N-m 1400 Nm FO 4 cm N.A.
3. A punch for making holes in steel plates is shown in Fig. a. Assume that a punch having a diameter of 19 mm is used to punch a hole in a 6-mm plate, as shown in the cross-sectional view (see figure (b)). If a force P=125kN is required, what is the average shear stress in the plate and the average compressive stress in the punch? (b) (a)