A thin square plate PQRS is symmetrically deformed into the shape shown by the dashed lines in the figure. Assume d = 255 mm, d₁=256.1 mm, and d₂ = 253.6 mm. For the deformed plate, determine (a) the normal strain of diagonal QS. (b) the shear strain Yxy at corner P. d₂ Q d d₁ Undeformed Calculate the deformation of diagonal QS. Answer: dos = 9810.3 -Deformed mm

A thin square plate PQRS is symmetrically deformed into the shape shown by the dashed lines in the figure. Assume d = 255 mm, d₁=256.1 mm, and d₂ = 253.6 mm. For the deformed plate, determine (a) the normal strain of diagonal QS. (b) the shear strain Yxy at corner P. d₂ Q d d₁ Undeformed Calculate the deformation of diagonal QS. Answer: dos = 9810.3 -Deformed mm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.7.19P: During a test of an airplane wing, the strain gage readings from a 45° rosette (see figure) are as...

See similar textbooks

Similar questions

An clement of material in plane strain (see figure) is subjected to strains ex= 480 × 10-6, Ey= 70 × l0-6, and yxy= 420 × l0-6. Determine the following quantities: (a) the strains for an element oriented at an angle 0 = 75°, (b) the principal strains, and (c) the maximum shear strains. Show the results on sketches of properly oriented elements.
A strain rosette (see figure) mounted on the surface of an automobile frame gives the following readings: gage A,310 × 10-6:gage B,180 × l0-6; and gage C. -160 × 10-6. Determine the principal strains and maximum shear strains, and show them on sketches of properly oriented elements.
The strains for an element of material in plane strain (see figure) are as follows: x = 480 ×10-6. y = 140 × l0-6, and xy = —350 x 10”. Determine the principals strains and maximum shear strains, and show these strains on sketches of properly oriented elements.
- 7.2-26 The strains on the surface of an experiment al device made of pure aluminum (E = 70 GPa. v = 0.33) and tested in a space shuttle were measured by means of strain gages. The gages were oriented as shown in the figure. and the measured strains were = 1100 X 106, h = 1496 X 10.6, and = 39.44 X l0_. What is the stress o in the x direction?
On the surface of a structural component in a space vehicle, the strains arc monitored by means of three strain gages arranged as shown in the figure. During a certain maneuver, the following strains were recorded: e, = 1100 X l0_6, 6h = 200 X lO_6, and e = 200 X 10-6. Determine the principal strains and principal stresses in the material. which is a magnesium alloy for which E = 6000 ksi and v = 0.35. Show the princ ipal strains and principal stresses on sketches of properly oriented elements.
A material is subjected to the following strain system,ex=200x10-6, ey=-56x10-6,yxy=230x10-6. Using graphical method, determine A. The principal strains B. The directions of principal strain axes C. The linear strain on an axis inclined at 50o counter clockwise to the direction of ex Given that young's modulus for the material is 207GN/m2 and the poisson's ratio is 0.27, determine the principal stresses
Part 1 A thin square plate PQRS is symmetrically deformed into the shape shown by the dashed lines in the figure. Assume d = 255 mm, d₁ = 256.1 mm, and d₂ = 253.6 mm. For the deformed plate, determine (a) the normal strain of diagonal QS. (b) the shear strain Yxy at corner P. d₂ Answer: dos d = i d₁ Undeformed Calculate the deformation of diagonal QS. R Deformed X mm
Q1 The 45° strain rosette is mounted on a steel robotic am as shown in Figure Ql. The robotic arm is made from steel with Esel = 200 GRA and poison ratio, v= 0.3. The following readings are obtained for each gauge: E=[Y+Z](10“) E = -250(10-) E= -200(10) Here the value of Y and Z depends on the 5th digit and 6th digit of your matric number as shown in Table 1. For example, if your matrix number is DD 070112 gives the value of Y=300 and Z-60: Table 1 5 digit of matric 6* digit of matric number number 250 300 350 30 2 60 3 400 3 90 4 450 120 5 500 150 6. 550 180 7 600 7 210 650 700 240 270 (a) Prove that &= E, and E, = E. Determine the shear strain, yand the normal strain, E, and &. (b) Estimate the in-plane principal strains and the angle associated with the principal strains, and (c) Calculate the principal stress associated with the prihcipal strains in (c). (d)
The 45° strain rosette shown in figure below is mounted on the surface of a thin shell. The following readings are obtained for each gage: ea, eb, and ec. Note that e, is negative. Determine: • Shear strain yay • Principal strains e1 and e2 • The rotation angle (magnitude and direction) from x-axis to reach the principal orientation. Indicate direction as clockwise or counter-clockwise. epsilon_a = 4.50E-04 epsilon_b = 2.00E-04 epsilon_c = -1.00E-04 y а b 45° 45°
The state of strain in a plane element is Ex = -300 x 10-6 , Ey= 450 x 10-6, and Yxy = 275 x 10-6. (a) Use the strain transformation equations to determine the equivalent strain components on an element oriented at an angle of 0 = 30° counterclockwise from the original position. (b) Sketch the deformed element due to these strains within the x-y plane.
The 45° strain rosette shown in figure below is mounted on the surface of a thin shell. The following readings are obtained for each gage: ea, eb, and ec .Note that Be is negative. Determine: • Shear strain yxy • Principal strains e1 and e2 · The rotation angle (magnitude and direction) from x-axis to reach the principal orientation. Indicate direction as clockwise or counter-clockwise. epsilon a = 4.50E-04 epsilon k= 2.00E-04 epsilons = -1.00E-04 %3D y а b 45° 45°
The Poisson ratio formula for an auxetic structure given in the figure is given as follows:H = 8 cm L = 4 cm α = 50 ° t = 5 mmThe strain value of the structure in the same direction as a result of the pull applied in the X axis from the bottom was measured as 0.26 mm / mm. Under the same loading condition:a) Calculate the strain on the Z axis of the structure.b) In this case, what is the strain type of the structure in the Z axis?