A torsion test shows that the shear modulus of an aluminum specimen is 4.60 x 106 psi. When the same specimen is used in a tensile test, the modulus of elasticity is found to be 12.2 x 106 psi. Find Poisson's ratio for the specimen.

A torsion test shows that the shear modulus of an aluminum specimen is 4.60 x 106 psi. When the same specimen is used in a tensile test, the modulus of elasticity is found to be 12.2 x 106 psi. Find Poisson's ratio for the specimen.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.5P: The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen...

See similar textbooks

Related questions

Q: A beam has a uniform dead load and live load has a fixed support at both ends. If the beam propertie...

Q: Problem 1: Find the horizontali displacement and rotation at point B. EI is constant. 5 KN 4m 5IN 4m

Q: With the given data: Gravel = 15%, Sand = 10%, Clay = 35%, Silt = 40 % Classify the soil according t...

Q: What is the support reaction Ve from the following figure? 10 kN 10 kN 10 kN C D E 2.0 m G! HA 2.0 m...

A: ASKED: To compute the support reaction VG. In order to compute the support reaction VG, we can use...

Q: For the beam shown, derive the expressions for V and M and draw the shear force and bending moment d...

Q: Problem 2: Draw the shear and moment diagram of the indeterminate beam. 75KN 17KN/m 60KN 40KN 10KN/m...

Q: 5. Calculate how many pieces of 10 mm.Ø x 7.60 meters (25') full-length steel bars would be needed f...

A: The no of steel bears of 10 mm dia and 7.6 m length required to make 10 stirrups

Q: WHAT ARE THE ROLES OF A PROFESSIONAL IN HANDLING ENGINEERING MANAGEMENT WORKS?

A: The scope of engineering management work is complicated and large. For this purpose, professionals a...

Q: The lap joint shown

Q: For the image above, find the shear force and bending moment diagram. Show calcs for all your work...

Q: PROBLEM 1 An open cylindrical container with a diameter of 1.2 m and height of 3 m contains oil at a...

A: The rotation of the cylindrical container leads to the formation of paraboloids. The volume of the o...

Q: Given data : Cohesion=50 KPa Angle of internal friction=31 degree Normal stress%3D120 KPa Determine ...

A: We have to determine the value of shear stress of the clay as per the given data in the question lik...

Q: A framed of 6 m span is carrying a central load of 10 kN as shown in Fig. 13.17. 10 kN 3 m 3 m 6 m F...

Q: 4. A 7700-kg boxcar traveling strikes a second car at rest. The two stick together and move off with...

A: Mass of the second car is 13860 kg.

Q: What is the Design mode?

A: In terms of construction, the word design mode refers to the process of creating a specific solution...

Q: The figure shown a motor pulling an object in an in clined surface determine the power required to m...

A: Given, Velocity = 3.5 m/s μ = 0.20

Q: Need help in my homework ty! Experience beased analysis in Prinicples of transportation engineering...

A: There are 3 major techniques which are used for trip generation analysis: 1. Cross classification 2....

Q: A framed of 6 m span is carrying a central load of 10 kN as shown in Fig. 13.17. 10 kN 3 m 3 m 6 m F...

Q: An eight-story commercial building is proposed to be constructed in Cavite. The structure shall be a...

A: Step 1: Eight storey = 7 floors + one roof Weight= 7x1800 +1700=14300 kN R=8.5 I=1 Ca=0.53 Cv=1.02 T...

Q: D C 1.8 m 1.8 m A B 2 m

Q: Determine the weight “W” of the heaviest cylinder that can be supported in the position as shown in ...

Q: V= = 18.97 kd/m3 ko=0.25 %3D 8- 4898; ko = r-18.54G kA/ms1 ko-0 29 1:5m 8 =45.04 379k/m3. V= 18.121 ...

Q: 3/4-inch di. emher

Q: metrical Curve is 200 m. Find: Elevation of the highest point of the curve. Elevation of point T, wh...

Q: What is the typical saturated permeability values for sand, silt and

A: Given data- typical saturated permeability values for sand, silt and clay

Q: a. For the beam shown below, determine the slope at point C. E=15,000 MPa, I= 2x10^8 mm4. Use area m...

A: P = 60KN L = 7.2m

Q: An embankment is shown in the figure. Determine the stress increase under the embankment at point A ...

Q: 79. A mild steel flat of width 100 mm and thickness 12 mm is bent into an arc of a circle of radius ...

A: given-Radius of curvature, R=10m=10000 mmE=200 GPa=200,000 MPaThickness t=12mm

Q: The rigid, horizontal slab is attached to two identical copper rods. There is a gap A = 0.18 mm betw...

Q: The bin is 2 m wide and is filled with oil to the depth shown. Determine the location of the resulta...

Q: In a pre-stress concrete beam section, net loss 10% and final pre-stressing force applied at X is 75...

Q: Classify the following soils using the Unified soil classification system. Give group symbols and gr...

A: USCS soil clsssification:Look at the % passing through sieve no 200=76>50%⇒FINE GRAINED SOIL

Q: What lump-sum amount of interest will be paid on a P12,000 loan that was made on May 1, 2021, and re...

A: To find lump sump amount of interest

Q: Derive the expressions for V and M and draw the shear force and bending moment diagram for the beam ...

Q: A family of four spends the summer vacation in Britania Group of Islands. They ride on a pump boat, ...

A: Given Driver weight 62kg Dad weigh 70kg Mom weight 56kg Daughter weight 46 kg Son 58 kg Equipment an...

Q: witl

Q: Calculate the moment of inertia about the y axis for the shape above. Enter you value into d21 answe...

Q: The car has a speed of 59.3 ft/s. If the curve is curcular, Determine the angular velocity, Ô of the...

A: Velocity and radius have been given and it has been asked to determine angular velocity. Please refe...

Q: For the beam shown, determine the following: a. Flexural stress at the edge of the topmost fiber at ...

A: ASKED: To determine: flexural stress at the topmost fiber at the midspan of the beam flexural stres...

Q: Agent Bond is standing on a bridge 15 m above the road below and his pursuers are getting too close ...

A: Velocity : The rate of change of an object's position with regard to a frame of reference is its vel...

Q: The figure shown a motor pulling an object in an inclined surface. Determine the power required to m...

A: Given: The mass of the block is 50 kg. The velocity is 3.5 m/sec. The coefficient of friction is 0.2...

Q: A 4-yard dragline is being used to excavate a canal in wet. sticky clay. The average swing angle is ...

A: Step 1: 4 yard drag lines Swing angle -75 deg Hcut=11 ft Job eff = 44 mins per hour BCY=1.578

Q: 1. Water is draining from a tank through a galvanized iron pipe. The pipe length is L = 2m, the tank...

A: Given Data -

Q: D 100 kg 300 kg B

Q: A rectangular concrete beam 250 mm wide and 600 mm deep is pre-stressed by means of 16 high tensile ...

A: GIVEN, A rectangular concrete beam of width=250mmDepth=600mmDiameter of wire=7mmEffective pre-stres...

Q: Q.12 The command area of a canal grows only one crop. i.e., wheat. The base period of wheat is 120 d...

A: Given-Base period, B=120 daysdelta ∆=40 cm=0.40 mdischarge Q=2 m3/s

Q: A 10-kg mass is initially moving up a smooth incline at 5 m/s. What distance up the incline will it ...

A: The quantity of matter in a physical body is referred to as its mass. It is also a measure of the bo...

Q: A horizontal curve with radius equal to 220 m and intersection angle of 126° is to be realigned by r...

Q: A sanitary house drain is to be installed on a single-storey house to serve 1 water closet, 1 washba...

A: Discharge Q=50 gpm=0.0022×50=2ft/sec3 Velocity v=2ft/sec

Q: settlement of PL^3/24ei at a

A: Given that, Settlement atA=PL324EI. The objective is to determine the SFD and BMD.

Question

100%

Mechanics of deformable bodies -solve with complete solution

Question 4
A torsion test shows that the shear modulus of an aluminum specimen is 4.60 x 106 psi. When the same specimen is
used in a tensile test, the modulus of elasticity is found to be 12.2 x 106 psi. Find Poisson's ratio for the specimen.

Branch of science that deals with the stationary and moving bodies under the influence of forces.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
A tensile test was performed on a metal specimen having a circular cross section with a diameter of 1 2 inch. The gage length (the length over which the elongation is measured) is 2 inches. For a load 13.5 kips, the elongation was 4.6610 3 inches. If the load is assumed to be within the linear elastic rang: of the material, determine the modulus of elasticity.
A steel specimen is tested in tension. The specimen is 25 mm wide by 12.5 mm thick in the test region. By monitoring the load dial of the testing machine, it was found that the specimen yielded at a load of 160 kN and fractured at 214 kN. a. Determine the tensile stress at yield and at fracture. b. If the original gauge length was 100 mm, estimate the gauge length when the specimen is stressed to 1/2 the yield stress.
5. A tensile test was done on a magnesium sample of original diameter and original length of 12mm 30mm respectively. The final length and diameter were 32.61mm and 11.74mm respectively. Plot the stress versus strain graph and determine: a. 0.2% proof stress b. Tensile strength c. % elongation d. % reduction e. Stress at fracture f. Modulus of Elasticity. 66 Force (N) Ext. 0.0112 0.0157 0.0199 0.0240 1.72 (mm) 177 327 462 797 1350 1720 2220 2690 2690 5.55 8.15 13.07 22.77 25.25
The following observations were made during a tensile test on a mild steel specimen 40 mm in diameter and 200 mm long. Elongation with 40 KN load (within limit of proportionality) Change in length=0.0202 mm. Determine stress and strain value
Question 4 A torsion test shows that the shear modulus of an aluminum specimen is 4.60 x 10° psi. When the same specimen is used in a tensile test, the modulus of elasticity is found to be 12.2 x 106 psi. Find Poisson's ratio for the specimen.
A)Define poison's ratio B)A tensile-test piece of diameter 10mm is subjected to an axial force of 15KN.If E for the material is 207KN/mm^2 and poison's ratio is 0.29, calculate the lateral strain and the change in diameter.
Question 4. A tensile test is carried out on a bar of mild steel of diameter 2 cm. The bar yields under a load of 80 Kn. It reaches a maximum load of 150 kN, and breaks finally at a load of 70 kN. Estimate: a)the tensile stress at the yield point b)the ultimate tensile stress c)the average stress at the breaking point if the diameter of the fractured neck is 1 cm.
A steel specimen is tested in tension. The specimen is 1 in. wide by 0.5 in. thick in the test region. By monitoring the load dial of the testing machine, it was found that the specimen yielded at a load of 36 kips and fractured at 48 kips.a. Determine the tensile stress at yield and at fracture.b. If the original gauge length was 4 in., estimate the gauge length when the specimen is stressed to 1/2 the yield stress.
The following observations were made during a tensile test on a mild steel specimen 40 mm in diameter and 200 mm long. Elongation is with 40 kN load (with in limit of proportionality) 8=0.0304mm, yield load = 161 kN, Maximum load = 242 kN Length of specimen at fracture = 249mm Find: 1) Young's Modulus of elasticity ; E 2) Yield point stress Ultimate stress 3) 4) Percentage elongation
In a standard tensile test, an aluminum rod of 20-mm diameter is subjected to a tension force of P- 30 kN. Knowing that E- 70 GPa, and the change in diameter of the rod- 0.00955 mm, determine the poissons' ratio v. 20n diateter gage length-150 0.33 O 0.6 0.29 O 0.35
The data shown in the table below were obtained from a tensile test of high-strength steel. The test specimen had a diameter of 13mm and a gage length of 50mm. At the fracture, the elongation between the gage marks was 3.0mm and the minimum diameter was 10.7mm. Plot the conventional stress-strain curve for the steel and determine the proportional limit, modulus of elasticity (i.e the slope of initial part of the stress-strain curve), yield stress at 0.1% offset, ultimate stress, percent elongation in 50mm, and percentage reduction in area Tensile-Test Data Load(kN) Elongation (mm) 5 0.005 10 0.015 30 0.048 50 0.084 60 0.099 64.5 0.109 67.0 0.119 68.0 0.137 69.0 0.160 70.0 0.229 72.0 0.259 76.0 0.330 84.0 0.584 92.0 0.853 100.0 1.288 112.0 2.814 113.0 Fracture