a. A round steel bar with an initial diameter of 20 mm and length of 2 m is placed in tension, supporting a load of 2000 kg. If the Young's modulus of the bar is 200 GPa what is the length of the bar when supporting the load (assuming it does not yield)? b. If the Poisson's ratio of the steel is 0.4, what will the diameter of the bar be when supporting the load?

a. A round steel bar with an initial diameter of 20 mm and length of 2 m is placed in tension, supporting a load of 2000 kg. If the Young's modulus of the bar is 200 GPa what is the length of the bar when supporting the load (assuming it does not yield)? b. If the Poisson's ratio of the steel is 0.4, what will the diameter of the bar be when supporting the load?

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
SITUATION. A steel plate ABCD of thickness t = 5mm is subjected to uniform stresses: = 100 MPa 0₂ = -60 MPa. Ox E =200GPa, v= 1/3 a = 160mm and b = 200 mm Calculate the change in thickness (mm). -0.0023 mm 0.0023 mm O O 0.0045 mm - 0.0045 mm Ł B AL C D X
The modulus of elasticity of mild steel is equal to .. .? .... .. a. 2 x 10ʻN/m? a. 2 x 10'N/m 2 b. 2 x 10° N/m 4 c. 2 x 10 N/mm 5 d. 2 x 10 N/mm Check
Situation 1: A rigid bar ABC weighs 10 kN/m. The compressive stress of the copper bar is 20 MPa. Answer the following questions: 3m B 2 m Copper L=3m A = 1500 mm² Brass C L = 2 m A = 1200 mm² A. What is the stress of the brass bar? Indicate if it will experience tension (T) or compression (C) (MPa) B. What is the minimum required diameter of the pin at A assuming that the pin connection is in double shear? Consider the allowable shearing stress of the pin as 15 MPa. Round your answer in a multiple of 5. (mm)
Q/ Find the Maximum stresses in Steel and Aluminum. Est= 210G pa and E al%3D 70 G pa ? W= 15 Kn.M 120mm 5m Al steel 60mm 140 mm
two rods attached to a rigid bar AB with negligible mass . A 101 kN load was applied at the end of this bar. The computed stresses for steel and bronze are Blank 1 mPa and Blank 2 mPa respectively.
Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress (in Mpa) in the bronze given that P= 188 kN? Express your answer in four decimal places.
Bar A was manufactured 2 mm less than bar B due to an error. The attachment of these bars to the rigid bar wouldcause a misfit of 2 mm. Calculate the initial stress in each assembly. Which of the two assembly configurationyou would recommend? Use modulus of elasticity of E = 80 GPa and diameter of the circular bars as 32 mm.
What is the value of reduction factor of the beam, if the stress in the steel is 400 MPa, and the Modulus of Elasticity of the Steel is 200,000 MPa. O 0.671 0.692 O 0.660 O 0.650 None of the Choices O 0.681
Determine the maximum tensile strength of the steel bar described by the following data Initial diameter = 12 mm Final diameter = 6.5 mm Initial length = 60 cm Final length = 86 cm Ultimate load = 5000 kgf
A 31 mm radius Steel is subjected to tensile test. Determine its yield and ultimate load it can carry in KN when the steel grade is 60 and 40. Determine also it's elongation using the stresses if the modulus of elasticity of steel is 231 GPa. Determine also the weight if the length is 31 m and 03 m. Need it asap.
QUESTION 3 The assembly consists of three steel rods and a horizontal bar BED. The structure supports a 36 kN load P located at middle of bar BED. Each of the rod AB and CD has a cross-sectional area of 200 mm² and rod EF has a 625 mm². Modulus of elasticity for steel is 200 GPa. Determine: (a) The change in length of rod EF. (b) The stress in each rod. 500 mm 400 mm