A. Horizontal curve has R=780 ft. what is the degree of curvature? B Ahorizontal ccurrve has a rradius of 780 ft if the tangent is 220 ft what is the length of the curve? CC a horizontal ccurve starts at STA(100+00.00) the PI is at STA(107+50.00). If the inclined aangel l is 36 degree where is PT

A. Horizontal curve has R=780 ft. what is the degree of curvature? B Ahorizontal ccurrve has a rradius of 780 ft if the tangent is 220 ft what is the length of the curve? CC a horizontal ccurve starts at STA(100+00.00) the PI is at STA(107+50.00). If the inclined aangel l is 36 degree where is PT

Traffic and Highway Engineering

5th Edition

ISBN:9781305156241

Author:Garber, Nicholas J.

Publisher:Garber, Nicholas J.

Chapter15: Geometric Design Of Highway Facilities

Section: Chapter Questions

Problem 7P

See similar textbooks

Related questions

Q: Question A horizontal pipe of non uniform cross section has water flow through it such that the…

A: Pressure at a point P1=40 kPa, Velocity V1=2 m/s, Velocity at point 2, V2=3 m/s, It is needed to…

Q: A channel is made to flow adjacent to a river with a separation distance of 3000 ft completely…

A: To solve for the requested values, we can use the Dupuit-Thiem equation for calculating the flow…

Q: PROBLEM #1: Determine the tension in each segment of the cable and the cable's total length. 7 ft 4…

Q: The hoop stress at a point on the surface of a thin cylindrical pressure vessel is computed to be…

A: A thin cylindrical pressure vessel having, The hoop stress is σh=30.0 MPa..

Q: AW 24 by 103 is used as a beam that is simply supported at its ends. The properties of the section…

A: d = 623.10 mm tw = 14.00 mm bf = 228.60 mmtf = 24.90 mm A = 19,548.00 mm2W = 153.76 kg/mrt = 59.18…

Q: If a fluid having viscosity 0.6 Ns/m² and density of 900 kg/m³, flows through a pipe of diameter 40…

A: Fluid viscosity μ=0.6 N-s/m2 Density ρ=900 kg/m3 Pipe diameter d=40 mm=0.04 m, Critical Reynold's…

Q: For the frame shown in the figure, determine the end moments using the method of slope-deflection.…

Q: 24. The reduced bearing of a 10 m long line is N30°E. The departure of the line is (a) 10.00 m (c)…

A: The reduced bearing of the line is N30°E The length of the line, L = 10m To determine the…

Q: verage normal stress (in MPa) one heel exerts on the floor. Assume the load is a e ignored. Also,…

Q: F₁70 kN and F2 = 60 kN. A is a pin, and F is a roller. Figure -2 m- 40 kN E 50 KN -2 m- H -2 m D C 1…

A: Given data- F1 = 70 KN F2 = 60 KN Find out - Force in member EH ?

Q: An earth dam of homogeneous section with a horizontal filter is shown in Fig. below. If the…

A: Answer We are given Top width = 8 m Height = 30 m Upstream Side slope 3 to 1 Downstream side slope 4…

Q: From the following table, draw the precedence network, perform the C calculations, and complete the…

A: ES = Early Start time LS = Latest Start time EF = Early Finish time LF = Latest Finish time TF =…

Q: Q.3 Find the discharge in each pipe for below problems. Solve each questions up to three trials. hf…

Q: The Reynold's number associated with a trapezoidal channel is 3,000,000. The ratio of fluid dynamic…

Q: For the load group and influence line shown, P₁ = 32 kips, P2 = 32 kips, P3 = 8 kips, a = 14', and b…

A: An influence line diagram for shear just to the left of 40' is given. To determine the value of…

Q: In 1-2 sentences, explain why you think the Aor. Landfill in Clark County, Nevada was chosen as a…

A: explain why the Aor. Landfill in Clark County, Nevada was chosen as a location for the landfill ?

Q: Classify the structure as statically determinate (Write SD), statically indeterminate (Write only…

A: Classification of Structure whether it is Statically Determinate or Statically Indeterminate or…

Q: O From the given trusses determice all the forces carried by each member the trusses shown: of 4 kn…

A: Given: Required : Force in each member

Q: 5: Open Traverse: Find the distance and direction of boundary AD.

A: ###Distance AD and Direction of AD of Open Traverse####

Q: 2. The section of a reinforced concrete T-beam has d = 400mm, bf=750mm, t= 100mm, bw = 300mm. The…

A: d= 400 mm bf = 750 mm t = 100 mm bw = 300 mm. diameter of bar = 32 mm # of bars (n) = 7 Fy = 415…

Q: Which of the following is not an eco-efficiency measure? a. fuel efficiency b. waste…

A: Eco efficiency is founded on the idea that more commodities may be produced while using less…

Q: A municipal wastewater flow of 1,000 m³/d contains 400 mg/L BOD5 and is treated to be in a trickling…

A: The design of a trickling filter involves 1.the determination of the required filter 2.media surface…

Q: A cantilever beam having a 4m span carries a uniformly distributed load throughout its length. The…

Q: The common tangent of a compound curve makes an angle of 120 from the tangent passing thru P.C. and…

A: The length of the common tangent is 70 m long. The radius of the second curve is 180 m The angle of…

Q: Draw bending moment (M) diagram for the structure given below.

A: Of Bending Moment Diagram of Given Structure####

Q: 3) The rainfall gauging station measurements of an 8-hour storm is given below. The initial and…

Q: 4 L Derive Elymax. (

A: This question is related to the Strength of the material from Civil Engineering. In this question ,…

Q: shear and Moment Diagram solution each of Draw with complete the value.

A: For SHEAR force diagram and BENDING moment Diagram of Given beam with reactions value#####

Q: Determine the product of inertia (lxy) for the composite

A: ###Product of Inertia Ixy about centroid axis x,y #####

Q: The truss is loaded and supported as shown. You may assume all joints are smooth pin connected.…

A: #####Determine the forces in members of truss AE,BE,CE ###

Q: Draw a moment diagram and determine the largest moment at support and field in the statically…

A: A statically indeterminate beam is given which is loaded with UDL of q kN/m throughout the beam. The…

Q: 1. A 10 mm thick steel pipe with inside diameter of 600 mm conveys water under a head of 480 m. b.…

A: The thickness of pipe(t)=10 mm Diameter of pipe(d)=600 mm Head of water(H)=480 m Let pressure…

Q: Note: Use sketch wherever necessary! (Q1) Compute the coordinate of point P in the below figure, if…

A: An open traverse ABCP is given. The azimuth of AB is αAB= 240°10'05'' The horizontal distance line…

Q: - A circular curve of radius R connects two straights with a deflection angle of 60°. The tangent…

A: Circular curve of radius = R Deflection angle ∆ = 60°, It is required to find the value of the…

Q: 1) Using Double Integrat. Method Compute Elymax of the loaded beam shown. ( IP 4/24/2

A: Simply supported beam with point load at middle of span

Q: Find the area of a water-plane which is 72 metres long, Using Simpson’s First Rule with the…

Q: Use the following table consisting of 2 hour Unit Hydrograph with constant rainfall intensity of 0.5…

Q: Determine the reactions at supports A and B of the parabolic arch shown in Figure P6.2. Also draw…

A: Since the arch is loaded symmetrically we get equal reactions at the support Ay = By = 900*1202 Ay…

Q: a=1m. Determine the reactions at the fixed support A when 1-2m and L 10 kN 5kN-m

A: A frame is loaded with a point load of 10kN at C (1m along the z-axis) and a twist of 5kNm at B (2m…

Q: A line CD has a length of 66.24m on the ground. What is the length of CD O CD on the map Ob CD on…

Q: Calculate the internal forces of M₁, T2 and Ny for the structure given below. 2m 4 m A (3) 6 m 80…

A: Find: M1, T2 and N3

Q: locate both highest and lowest point in terms of horizontal distance from PVT station and difference…

A: Of location of both highest and lowest point in terms of horizontal distance from PVT station and…

Q: A municipal wastewater flow of 1,000 m³/d contains 400 mg/L BOD5 and is treated to be in a trickling…

A: A municipal wastewater contains BOD5 is 400 mg/L A municipal wastewater flow is 1000 m3/d Specific…

Q: When the reading was taken on a staff held at a point of known elevation of 123.45 m, the staff…

A: The reading is taken on a staff- Elevation or the Reduced Level RL=123.45 m, Staff reading or Back…

Q: Using Macaulay's method, determine maximum deflection in the beam. El = 41000 kN.m².

A: The Maximum Deflection in the Beam using MACAULAY METHOD of double Integration ###

Q: For a homogeneous earth dam 52 m high and 2 m free board, a flow net was constructed and number of…

A: Earth dam details: Dam height = 52 m Freeboard = 2 m Coefficient of permeability of dam, k = 3 x…

Q: O 6.14 For a beam having the cross section shown, deter- mine the largest allowable vertical shear…

Q: 1000 Ib

Q: Can you please share the process of above drawing in space gass software? Like, what you have sone…

A: Can you please share the process of above drawing in space gass software?Like, what you have done…

Q: Part B-Zero-force members in a loaded truss Consider the loaded truss shown below. Identify the…

A: A truss is given with hinged support at A and roller support at G. To determine zero-force…

Concept explainers

Electronic Spreadsheet

Tabular listing has many advantages ranging from time management to efficient scheduling of tasks. Electronic spreadsheets allow the user to tabulate and analyze data, using its easy-to-use interface. An electronic spreadsheet is a staple application used among accountants, management staff, and IT professionals. It is used in various sectors worldwide for data management. An electronic spreadsheet is a system and computer software that could be used to do numerical computations automatically. Spreadsheet application programs are often organized as a table with rows and columns. Each row and column intersect to form a cell, which may be used to store data. These data can take the form of a written label, a number, or a formula that combines information from other cells.

Question

A. Horizontal curve has R=780 ft. what is the degree of curvature?

B Ahorizontal ccurrve has a rradius of 780 ft if the tangent is 220 ft what is the length of the curve?

CC a horizontal ccurve starts at STA(100+00.00) the PI is at STA(107+50.00). If the inclined aangel l is 36 degree where is PT

Pleeasee help

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data:

VIEW

Step 2: Calculations:

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 6° simple curve has a central angle of 44°. The stationing of the point of intersection is 0+082.54 and a backward bearing of S 43° E. a.) FInd the radius b.) determine the P.C. and P.T.
A circular curve with a radius of 450m is connected by 75m spiral transition curve to tangents with a central angle, Ic= 30o. Determine the length of throw Determine the stationing of ST if TS is at 2+450 Determine the spiral angle
Two tangents having an azimuth of 235° and 277° meet at station 30+28.212 are connected by a 330ft spiral curvewith a 5° circular curve used for light rail transit.a) Determine the difference between the external distance of the spiral and the central curve.b) Determine the minimum super-elevation of the curve at the two-thirds of the spiral with the railway width of 15ft. If g= 32.2 ft/s^2c) Determine the stationing of the S.T.
A symmetrical parabolic curve passes through point A whose elevation is 23 23m at a distance of 54 meters from PC The elevation of the P.C. at station 4+100 is 22.56m. The grade of the back tangent is +2% and the length of the curve is 120m. Determine the grade of the forward tangent a. -2.3% b. -1.4% c. -3.3% d. 2.5%
A parabolic curve AB, 400 m. long is connected by tangents having an upgrade of +6.5% and a downgrade of -3% intersecting at sta. 20 + 800 at elevation 102.5 m. Find the distance from B to the highest point of the curve
A vertical sag parabolic curve has a length of curve of 420 m. from A to B. The back tangent has a slope of −3.2% and the point of intersection of the tangents is at station 7 + 180 with an elevation of 998 m. Find the elevation of point A.
If R= 725 ft V= 35 mph f= 0.10 what should be the super elevation of the curve be? show steps and explain
12. A sag curve is composed of two parabolic curves. BVC and EVC have elevations 250.30m and 246.30m respectively. The grade of the tangents is -3.5% at BVC (1+300) and +5.5% at EVC (1+800). What is the grade of the common tangent? a) 1.25% c) 0.008% b) 0.08% d) 0.8% 13. Compute the deflection angle at the endpoint of the spiral if the length of spiral is 52m and the degree of the central curve equal to 7.5⁰ a) 3.25⁰ c) 3.52⁰ b) 2.35 d) 2.53 14.
an unsymmetrical parabolic curve has a forward tangent of -8% and a back tangent of +5%. the length of the curve on the left side of the curve is 40m long while the right side is 60m long PC is at Sta. 66 + 780 and at Elev. 110m determine the height of fill at the crop (30m from PC with top elevation of 108.,40m)
A vertical parabolic curve CD,620 meters long is connected by tangents having a downgrade of 6.2% and upgrade 0f 4.2% intersecting at Station 18+254.4 and elevation 54.25m. find the distance from D to the lowest point of the curve.
he two tangents having an azimuth of 240° and 282° are connected by an 80m. spiral curve with a 6 degrees circular curve. The width of the roadway is 10m. If the design velocity is 60kph. (Embankment = E = e * width of roadway) a.) Determine the embankment of the spiral curve. b.) Determine the deflection angle at the end of points (S.C.) c.) Determine the length of external distance
A 6°simple curve connects two tangents that intersect the PC which is at station 0 + 168.150 is to be retained and a 4°curve is to connect the first curve with the second tangent that is shifted 20 meters to a parallel position outward, find the PCC and the new PT. Use chord basis.