After a fall, a 110 kg rock climber finds himself dangling from the end of a rope that had been 15 m long and 9.9 mm in diameter but has stretched by 2.1 cm. For the rope, calculate (a) the strain, (b) the stress, and (c) the Young's modulus. (a) Number 0.0014 Units This answer has no units (b) Number i 1.4 Units N/m^2 or Pa (c) Number 1.0012 Units N/m^2 or Pa >

After a fall, a 110 kg rock climber finds himself dangling from the end of a rope that had been 15 m long and 9.9 mm in diameter but has stretched by 2.1 cm. For the rope, calculate (a) the strain, (b) the stress, and (c) the Young's modulus. (a) Number 0.0014 Units This answer has no units (b) Number i 1.4 Units N/m^2 or Pa (c) Number 1.0012 Units N/m^2 or Pa >

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter12: Static Equilibrium And Elasticity

Section: Chapter Questions

Problem 60P: A 100-N weight is attached to a free end of a metallic wire that hangs from the ceiling. When a...

See similar textbooks

Similar questions

An aluminium (=2.7g/cm3) wire is suspended from the ceiling and hangs vertically. How long must the wire be before the stress at its upper end reaches the proportionality limit, which is 8.0107N/m2 ?
Two rods, one made of copper and the other of steel, have the same dimensions. If the copper rod stretches by 0.15mm under some stress, how much does the steel rod stretch under the same stress?
A steel cable 2.00 m in length and with cross-sectional radius 0.350 mm is used to suspend from the ceiling a 10.0-kg model aircraft that is flying in a horizontal circle with an angular speed of 6.00 rad/s. What is the strain produced in the cable?
Alarge uniform cylindrical steel rod of density =7.8g/cm3 is 2.0 m long and has a diameter of 5.0 cm. the rod is fastened to a concrete floor with its long axis vertical.what is the normal stress in the rod at the cross-section located at (a)1.0 mfrom its lower end?(b)1.5 m from the lower end?
In Example 14.3, we found that one of the steel cables supporting an airplane at the Udvar-Hazy Center was under a tension of 9.30 103 N. Assume the cable has a diameter of 2.30 era and an initial length of 8.00 m before the plane is suspended on the cable. How much longer is the cable when the plane is suspended on it?
A company is testing a new material made of recycled plastic for use in construction. Figure P14.48 is a graph of the stress as a function of strain for this material. Find Youngs modulus for this material and compare your result with the data for conventional building materials listed in Table 14.1.
Review the relationship between stress and strain. Can you find any similarities between the two quantities?
Can Young’s modulus have a negative value? What about the bulk modulus?
(a) When water freezes, its volume increases by 9.05% (that is, V/V0=9.05102 ). What force per unit area is water capable of exerting on a container when it freezes? (It is acceptable to use the bulk modulus of water in this problem.) (b) Is it surprising that such forces can fracture engine blocks, boulders, and the like?
Assume Youngs modulus for bone is 1.50 1010 N/m2. The bone breaks if stress greater than 1.50 108 N/m2 is imposed on it. (a) What is the maximum force that can be exerted on the femur bone in the leg if it has a minimum effective diameter of 2.50 cm? (b) If this much force is applied compressively, by how much does the 25.0-cm-long bone shorten?
A brass wire and a steel wire, both of the same length, are extended by 1.0 mm under the same force. Is the cross-sectional radius of the brass wire more, less, or equal to the cross-sectional radius of the steel wire? Explain. Youngs moduli for brass and steel are 1.0 1010 N/m2 and 2.0 1011 N/m2, respectively.
Two thin rods, one made of steel and the other of aluminium, are joined end to end. Each rod is 2.0m long and has cross-sectional area 9.1mm2 . If a 10,000N tensile force is applied at each end of the combination, find: (a) stress in each rod; (b) strain in each rod; and, (c) elongation of each rod.