#ammend this code for the inputs (x = 5.01, 4.99, 0, -2.01, -1.99) so that there is a tolerance/Leeway for the values off #such that 4.99 prints blue and -2.01 prints orange. # cannot adjust the value to x > 4.99 instead of 5 must add new code to add a tolerance or Leeway if x > 5: print ("blue") elif x < -2: print ("orange") else: print("purple")

#ammend this code for the inputs (x = 5.01, 4.99, 0, -2.01, -1.99) so that there is a tolerance/Leeway for the values off #such that 4.99 prints blue and -2.01 prints orange. # cannot adjust the value to x > 4.99 instead of 5 must add new code to add a tolerance or Leeway if x > 5: print ("blue") elif x < -2: print ("orange") else: print("purple")

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Implement the counter increment and return to the beginning of the loop. When you finish these stages, you should have the fundamental structure of the counter control loop established, and your code should look like this:.text li $s0, 0 lw $s1, n start_loop: sle $t1, $s0, $s1 beqz $t1, end_loop # code block addi $s0, $s0, 1 b start_loop end_loop:.datan:.word 5
This code has a delay in the loop, during which time the user inputs will be ignored. So, please modify it and implement a solution that would trigger the needed function when there is an input. // Pin numbers written on the board itself do not correspond to Aurdino pinnumbers.Constants are defined to make using this board easierconst uint8_t BTN_PIN = 2;const uint8_t LED_PIN = 13;//assigning button;s previous state and LedSate to LOWuint8_t buttonPrevState = LOW;uint8_t ledState = LOW;//defining a new functionvoid setup(){// Assigning the types of input parameterspinMode(BTN_PIN, INPUT_PULLUP);//Assigning the types of output parameterspinMode(LED_PIN, OUTPUT);//begin of process detailsSerial.begin(9600);}void loop(){//assigning button state to be read modeuint8_t buttonState = digitalRead(BTN_PIN); //To print the following in output windowSerial.print(buttonState);Serial.print(buttonPrevState);Serial.print(ledState);Serial.println(""); //check if the button state presently is same…
Please discuss this Arduino code int redPin = 10; //set red LED pin to 10 int bluePin = 11; //set blue LED pin to 11 String colorChoice; //Will hold users input of color choice void setup() { // put your setup code here, to run once: pinMode(bluePin, OUTPUT); //Set redPin to be an output pinMode(redPin, OUTPUT); //Set greenPin to be an output Serial.begin(9600); //Turn on Serial port } void loop() { Serial.println("What color do you want to blink up, red or blue?"); //Prompt user for color while (Serial.available() == 0) { } //Wait for input colorChoice = Serial.readString(); if (colorChoice == "red") { digitalWrite(redPin, HIGH); delay(1000); digitalWrite(redPin, LOW); delay(1000); } if (colorChoice == "blue") { digitalWrite(bluePin, HIGH); delay(1000); digitalWrite(bluePin, LOW); delay(1000); } if (colorChoice!="red" && colorChoice != "blue") { Serial.println("That is not a valid color choice, please try again"); Serial.println(""); } }
The pseudocode for implementing the Taylor series expansion is shown below. The pseudocode is designed to return the value of the value of e* correct to two decimal places. This also requires the use of the factorial function created in the previous section. INPUT x, OUTPUT ExpVal % Initial computation n- 0, xold - 0 xnew - xold + (x^n)/nl error = |xnew - xold| xold = xnew n-1 %Successive computations WHILE error 2 0.001 xnew - xold + (x^n)/nl error |xnew - xold xold - xnew n=n+1 END WHILE ExpVal = xnew Question 10: Write a script taylor.m that computes the value of the function e* for a given user input x. Provide La proof that your script works.
Help me write code for the scale down function please, make sure the size of the block can't become smaller than 2x2
Q/Write a bout the Critical- section problem.
Program this one
Which of the following is true when comparing sentinel loops and user confirmation loops? Select one: a. Both types of loops may not iterate at all. b. A user confirmation loop can do no iterations, but a sentinel loop has to iterate at least once. c. A user confirmation loop iterates at least once, but a sentinel loop can do no iterations. d. Both types of loops must iterate at least once.
: Find the weakest precondition for the following code. Show all intermediate conditions. Simplify your answer Question 4. as much as possible. { } // This is the weakest precondition. Please fill in. x++; { } // This is an intermediate condition. Please fill in. if (z != 5) { { } // This is an intermediate condition. Please fill in. z = x + 1; { } // This is an intermediate condition. Please fill in. y { } %3D z; } // This is an intermediate condition. Please fill in. { } // This is an intermediate condition. Please fill in. Z = y z; { z != 0 } // This is the postcondition.
Generate test cases for the following code by using MC/DC. a) Draw the CFG. b) What is MC/DC logic coverage criteria? c) List the test cases. d) Validate the test cases can achieve MC/DC. public void TestValues( int a, int b, ref int x) { } x = 0; if (a> 0 || b 10 && b > 10) x = -1;
Q2/A/ Design a Matlab code to evaluate the equation P(x) x3 + 3x? 9 at x is zeros(3)? Execute the code and return the result.
A calculator is an electronic device that is used to perform arithmetic operations like addition, subtraction, multiplication, division, etc. You are requested to develop an embedded software of a calculator with following specifications: a. This program takes an arithmetic operator (+, -, *, /) and two operands as the input. b. It also checks whether the user wants to quit the program, if yes then terminate the program execution. For this, you can use a special character and tell the user about it, like here we used "X". C. The arithmetic operation is performed based on the operator and two operands inserted by user in (a). d. Display the complete arithmetic operation which includes the 2 operands, the arithmetic operator, and the computation result. Figure 5 shows samples of expected program execution output display for your reference in solution development. Enter an operator (+, -, *, /) or 'x' to exit: + Enter two operands: 7.3 8.9 7.30 +8.90 = 16.20 Enter an operator (+, -, *, /)…