At times t=0, 1, and 2 seconds, processes P1, P2, and P3 arrive in the Ready state, respectively. Suppose their execution times are 5 seconds, 4 seconds, and 3 seconds, respectively. Show how they will be scheduled using round robin scheduling with a quantum of 3 seconds. Calculate the average turnaround time per process.

At times t=0, 1, and 2 seconds, processes P1, P2, and P3 arrive in the Ready state, respectively. Suppose their execution times are 5 seconds, 4 seconds, and 3 seconds, respectively. Show how they will be scheduled using round robin scheduling with a quantum of 3 seconds. Calculate the average turnaround time per process.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

3. Peak time is the time required for the response to reach the first peak of the overshoot. * True False 4. The loops called non toughing loop if they have many node in common. True False 5. First type system has a zero static steady state error when the input function is a step function. * True False
Perform the following subtraction using 1’s and 2’s complement method (Show step by step process) (i) (11010)2 – (10000)2 (ii) (1000100)2 – (1010100)2
lo 4) obtain the analysis of the synchronous sequential circuit (State table and state diagram) in the figure below. What structure does the circuit have from Moore and Mealy type machines? 8 Q1 Or FF FF 4. 01 K1 R
DA stamping device is used for work on sheet metal work piece. The puncher that moved by double acting cylinder (DAC- A) with sp stamp the sheet metal and lefur retracted back to its position. While the sheet metal inside the blank will push out using another DAC- B and retracted back with Spring return ) Design an Pneumatic-PLC circuit by using 5/2 way valve.
Hello. I think I am close but I wanted to check my process. What is the best way to take on this problem. Thank you.
For the following circuit, form the ASM flowchart and state if it is a Mealy or Mooresteate machine.
The p.u parameters for a 500 MVA machine on its own base are: inertia,M=20 p.u.;Reactance X=2 p.u. What is the p.u value of inertia and reactance on 100 MVA COMMON BASE. Ans is 100,0.4
Explain the Commutation process in DC machines. Files
For a dc machine, its commutator has a diameter of 50 c rotating at 1000 rpm. For a brush width of 1 cm, the time commutation taken by the machine will be _________a) 0.382 msb) 0.456 msc) 0.573 msd) 0.312 ms
3c.The initial load angle at steady-state stability is δ0 and the related mechanical power, P0. With the occurrence of a transient fault the load angle advances to δ1 with a corresponding electrical power of P1. After the successful clearance of the fault the load angle moves to δ2 and electrical power, P2. Use the given information to answer the following questions. Derive equations for: i) the accelerating area. ii) the decelerating area iii) the critical clearing angle
b. Illustrate the salient effect of a sudden symmetrical short circuit across the terminals of a synchronous machine, and name the condition. c. The transient reactance in a synchronous machine is defined as the ratio of no-load voltage to the short-circuit current during transient period. Sketch its equivalent-circuit representation.
Consider the system in figure below where ? = 0.6 and ?? = 5 ???/???.determineRise time Peak time Maximum overshoot Delay time Settling time, when the system is subjected to a unit step function.